In this video I construct a jig for hand planing small stock to precise and repeatable thickness.
Пікірлер: 133
@garyfairbrother55323 жыл бұрын
At 77 I’m going to try my hand at Kumiko so I’ve been researching on KZfaq and found your jig build to be simple, clever, and accurate. I just finished a small 11 inch version of it to use with my block plane. I’ve got the blocks and starter set ordered and once that gets here I should be set. My version of your little planing jig is accurate to 1 thou in 11 inches so because I’m only doing this on a small scale for my own pleasure it should be sufficient. I plan to use it for accenting small items like boxes, napkin holders, coasters, etc. the only change from your design was I used nylon 1/4 -20 bolts for the elevation adjusting sides. I got all the parts from a 4x4 Douglas fir cut off. Thanks for the good plan and the (something from nothing) fun build.
@okieinva17 жыл бұрын
Glad to see you back in the wood shop Marty! Nice jig build.
@christopherkouri23177 жыл бұрын
Ok so I hope you take this as the compliment that I mean it to be...You are the Mr. Rogers of woodworking videos! Love it! Not to mention a super cool jig build! Thank you for sharing!
@MartyBacke7 жыл бұрын
Thanks :-)
@Jay2525Jay7 жыл бұрын
Just wanted to thank you for sharing your skills and knowledge. The jig is awesome. I enjoyed your laid-back style. Thanks
@jasonrobinson95244 жыл бұрын
Extremely well executed. Thank you for sharing your method.
@robertbrunston54066 жыл бұрын
Watched this one again, I still need to make one of these jigs, I use the table saw but I need a better way to do it! Thank you Marty.
@robertbrunston54066 жыл бұрын
I can see you would use this jig a lot! Thank you for sharing Marty.
@bighands693 жыл бұрын
You can use jigs like that to produce all manner of things from table legs, door stiles, face frames and so on.
@PhilMakesThings7 жыл бұрын
It's great to see you back in the workshop, and a very nice little jig. I'm always impressed on how clean your workshop looks... It's immaculate!
@MartyBacke7 жыл бұрын
Thanks. I think my shop is a bit on the messy side ;-)
@MD-en3zm4 жыл бұрын
This is a clever idea, and not something I’ve seen before. Thanks for sharing.
@jrlejeune7 жыл бұрын
He's BAAAaaak(e)!!! Thanks Marty I've missed your Zen woodworking videos. Just installed a Jerdon mirror in our WC because of your inspiration. The only problem now is, I now know how bad my morning shaves were previous to the mirror installation. :-O
@MartyBacke7 жыл бұрын
Funny John. After I installed that first mirror for my wife I did install one for me two. They're both still working fine.
@acanadianwoodworker3 жыл бұрын
Wow your feed rate into your tables is so slow and easy. Bet the cuts are flawless
@seanc2157 жыл бұрын
Fantastic idea. I appreciate how much effort you put into even a prototype jig for your shop. Thanks for the video.
@MartyBacke7 жыл бұрын
Thank you.
@GuysShop7 жыл бұрын
Pretty cool Marty. And I appreciate the making of the jig to make the slots in the side "risers". Jig making to solve a challenge is to me an important part of woodworking. And of course when you make a jig to make a jig, it's always a fun day in the shop :)
@MartyBacke7 жыл бұрын
Hey Guy, and thanks. Jig making can be very satisfying when you see the end result :-)
@eversleyowl7 жыл бұрын
Great that you are making woodworking videos again, always loved your delivery style. And a very useful jig to boot. I hope there is more to come from the workshop!
@MartyBacke7 жыл бұрын
Thank you. More are in the pipeline :-)
@treebangham7 жыл бұрын
Great idea Marty. A mini thickness planer! I need to make one.
@MartyBacke7 жыл бұрын
Really does work nicely. Worth your while if you use small thin parts.
@erikrazie7 жыл бұрын
Love the return to woodworking vids!
@MartyBacke7 жыл бұрын
Thanks :-)
@dan__________________6 жыл бұрын
Just finished making one. Works great!
@MartyBacke6 жыл бұрын
Cool. Hopefully it'll come in handy every once in awhile like mine does for me.
@MrKYT-gb8gs8 ай бұрын
Brilliant! Excellent idea/design.
@tabhorian6 жыл бұрын
Good idea, I might have to add this to my arsenal. I would try bevelling the rails so that when you reinsert the plane each time it will be easier.
@BoxcarJerry7 жыл бұрын
good to see you making woodworking videos again .
@caroleburns72775 жыл бұрын
Thank you, best one I have seen beautiful job.
@robbysearle6 жыл бұрын
Marty, great jig, I was looking for a taper jig and came across yours, which of course can be tapering as well. Well done
@MartyBacke6 жыл бұрын
Thanks :-)
@68HC0603 жыл бұрын
This is a very good video and a very good and useful build. I've seen similar builds on KZfaq (both some simpler and some more advanced), this build is advanced enough to allow adjustment while being simple enough for most basic woodworkers to make. In addition, you can make jigs like this for 'taller' pieces (eg if you need to make the sides of a wide board parallel). The body of the jig in this build stands on the workbench, which can be preferable, however, in some situations, you may wish to make a variant where the adjustable side pieces stand on the workbench, so there will be a space under the jig itself. This will have the advantage of not moving the workpiece when you push the plane downwards while planing; it'll also allow you to have a 'template' shim under the jig. To further reduce the chance of the sides sliding out of position, you can also glue fine-grained sandpaper onto each side. -Or you could use beeswax as 'anti-skid', but the sandpaper might be preferable. I believe that the best way to avoid the sides sliding, could be to set the jig up in a vise, if you have one. Marty, thank you for taking the time making this video; this jig is definitely one that makes a valuable addition to any woodworking workshop.
@d.i.d7 жыл бұрын
Very good jig!
@MartyBacke7 жыл бұрын
Thank you
@nayrb111117 жыл бұрын
Awesome will be building one, only one suggestion epoxying in threaded inserts.
@MartyBacke7 жыл бұрын
I enjoy using tapped holes whenever I can. They are much stronger than many people think they are. Of course threaded inserts work fine too, but I really don't think epoxy would be necessary for this application.
@joemassanova71845 жыл бұрын
Hey Marty, good Video. Nice shirt. I worked for Sun for 15 years.
@MartyBacke5 жыл бұрын
Thanks. I always liked working with Sun products
@robertbrunston54066 жыл бұрын
Long time no see Marty! Very cool jig! Thanks for sharing.
@MartyBacke6 жыл бұрын
Thanks :-)
@DrewMarold5 жыл бұрын
You just saved me from having to buy a thickness sander for the project I'm working on, which is good since I didn't have room for it anyway.
@Lazasakh7 жыл бұрын
Nice jig, thnx for video! I used to plain small parts in standart machine planner having well sanded piece of wood as a base )
@MartyBacke7 жыл бұрын
I use a planer too, but there's nothing like the finish that you can achieve straight from the hand plane. And no matter what kind of power planer jig you use, trying to plane 1/16" thick wood is not going to end well ;-) Thanks for watching.
@bloho_design6 жыл бұрын
I have been using matt kenney's fixed version of this jig for a while and was about to make several more when I came across your video. Neat idea -- especially the use of known thickness material to set the rail height. For stock less than a 1/16th I have been using the veritas thickness plane, but it is a bit finicky.
@MartyBacke6 жыл бұрын
It's certainly worth experimenting with a jig like mine. I find it very effective. When it wears out I'll make a more robust version of it.
@johnvanderhoof12484 жыл бұрын
I don't have a thickness sander and don't want to buy one. I have the same # LN hand plane that you do. Would like to incorporate that more into my work. Cherry and Purple Heart have a tendency to tear out. Especially when I get down to finish thickness for my boxes. Thanks again, I love your attention to detail, it is inspiring.
@mikehill34264 жыл бұрын
I made one based on this video. The only thing I did differently was use 1 piece with a rabbet for each side. Works great.
@MartyBacke4 жыл бұрын
Fantastic. Thanks for letting me know :-)
@heriberthuber547 жыл бұрын
What a great little jig! I could use one like that :-)
@MartyBacke7 жыл бұрын
Thanks!
@jhart73045 жыл бұрын
Upvoted and subscribed 5 minutes in. Everything is about details. Thank you for this video. Send me the jig!!!
@davidbell76582 жыл бұрын
Thankyou from Australia, regards Dave Bell
@johnchung69007 жыл бұрын
Good video there. Worth the effort for the jig.
@MartyBacke7 жыл бұрын
Thanks.
@bryanwavechapman17 жыл бұрын
Good idea!
@nodarikirtadze82202 жыл бұрын
Thanks, that's a cool project
@tooljunkie5557 жыл бұрын
thats a cool jig and a good idea man!
@MartyBacke7 жыл бұрын
Thanks Joe.
@tooljunkie5557 жыл бұрын
Marty Backe always! Glad to see ya back to woidworking 👍 although that two wheels machine you have is pretty cool
@raytbrown27 жыл бұрын
Neat jig. Nice videos.
@lewislevine80959 ай бұрын
Nice jig, thanks
@cinocrossed6095 жыл бұрын
Love the concept behind the jig and how clean it will give you parts for fine shelving, drawers, and boxes. Would making the sides one piece with a rabbit in it as a plane carrier have been better? Just thinking...
@MartyBacke5 жыл бұрын
There are lots of variations on this general concept. This was my approach which but I think the rabbet implementation would work also.
@SoundsToBlowYourMind7 жыл бұрын
Nice jig, but how well will those threaded holes last in Poplar ? The end stop in particular which is in end grain. Wouldn't it be better with something a little harder?
@MartyBacke7 жыл бұрын
Thanks. I'm not cranking down hard on the bolts, and they feel nice and strong with no signs of weakening (it's amazing how strong threaded holes are in wood). However you are correct that poplar is not the best choice for a long term jig. One of the purposes of this jig was to determine if the design would work, and I'm really happy with the results. I'm going to continue to use it and if or when it shows signs of wearing out I'll make another one with maple. I can tell that the end grain hole is not strong, but that's mitigated because the end is against a bench dog which takes all the planing stress. In my next one I may opt for a threaded insert for the end. Thanks again for the comment.
@SoundsToBlowYourMind7 жыл бұрын
You could also glue in a dowel near the end of the board, in line with the machine screw, so you have some cross grain for the threads to get a better hold.
@luisurbina51156 жыл бұрын
You could strengthen those threads with thin CA. I was surprised to see you tap with a drill. I always thought that was a no-no, because it would strip right away. I will try that
@safelinefleet66335 жыл бұрын
The actual force of the push by the plane is taken by the plug stop in the work bench. There would be very little to none force on the screw and the threads itself. The main purpose of the screw would be just to keep the end stop in place. That being so, I wonder why the need for a metal screw here. A simple wood screw would have done fine. This is based on my observation, but please do correct me if I'm wrong.
@christiandestefano99972 жыл бұрын
ultimate precision
@KarlBunker6 жыл бұрын
Nice jig! I think I'll make one if I find myself making more small boxes. Perhaps an improvement would be to put a bevel on the tops of the guide rails to make it easier to drop the plane down between them. BTW, this is also a tapering jig -- you'd just have to tighten the guide rails at an angle. I like the tone and pace of your videos, and also how neat your shop is. :-)
@MartyBacke6 жыл бұрын
You are right of course regarding its use as a tapering jig - I hadn't thought of that. Then again I never seem to need tapered wood of this size. But it's useful to note this 'feature'. Thank you for compliments :-)
@Withplaneandsaw7 жыл бұрын
you remind me of frank howarth
@julioaragao7 жыл бұрын
Great job! One question: What are the spacers glued on the side for? Cheers!
@MartyBacke7 жыл бұрын
Thanks. You may have missed the section towards the beginning of the video where I explain the spacers. By accident I made the original block too narrow for my #4 planes. So the spacers were added to widen the block.
@julioaragao7 жыл бұрын
Marty Backe Oops, yeah, I didn't quite get that part. I just saw it now! Thank you! And keep going with your projects!
@jonsoncw4 жыл бұрын
Could also be used to copy a taper for a small piece.
@alfredobanuelos47302 жыл бұрын
Helpful jig. Provided another idea for a different application. Where did you get that clamp that goes into the bench’s dog hole
@ejtakach7 жыл бұрын
I looked back and now see it. My bad, great jig!
@MartyBacke7 жыл бұрын
Thanks for your note!
@davidosullivan34325 жыл бұрын
An fancy version of the Paul sellers jig.
@MartyBacke5 жыл бұрын
I can assure you that Paul did not invent this jig. People were making this jig before Paul was born :-)
@Belg19703 жыл бұрын
To what grit and angle do you sharpen your plane irons? Very clever and useful jig. I like the router jig as well, two for one bonus. How come you stopped making videos, loved your attention to detail?
@MartyBacke3 жыл бұрын
~4000 grit and the angle varies depending on the blade. ~25. Thanks for the compliment :-)
@_J.F_5 жыл бұрын
Very nice jig. A bit surprising that you just chiselled out a square slot in the stop block, when you could have made a router jig and routed a nice slot similar to the side guards.
@MartyBacke5 жыл бұрын
I enjoy using hand tools and sometimes they are quicker for work like this (a single hole)
@TjallingBlackCat7 жыл бұрын
Fantastic jig! Just a quick question: you use a spacer to set the thickness of your finished parts, but that doesn't take into account the fact that the blade protrudes from the bottom of the plane, does it? Or is that a negligible difference in your opinion?
@jonsoncw4 жыл бұрын
Tjalling if you set the jig to zero which would mean no spacer under neath and take a couple passes with the plane before hande you can zero that blade protrusion out. If you just always set your plane up the same and use the same plane every time it will always be true to that. And also the plane is taking off a very small amount so you would get fairly close no matter what and then you can just stop planing once you get to your desired thickness.
@johnvanderhoof12484 жыл бұрын
Nice Marty. Would you find it practical to make a jig like this for a wider box; such as 3 1/2 to inches?
@MartyBacke4 жыл бұрын
This technique is limited to the width of your hand plane. There are no 3-1/2 inch wide handplanes that I'm aware of.
@pcka123 жыл бұрын
Nice jig, but why would you use a low angle plane to cut with the grain of the wood?
@TheKingsOutlaw7 жыл бұрын
Where did you get your dog hole clamp? Brand? Thanks!
Threaded holes in poplar? A wood screw would probably hold up longer. I just cut 6 slots for screws with a drill and coping saw. Took about 8 minutes. How long did it take to build that jig?
@MartyBacke6 жыл бұрын
The threaded holes in poplar work in this application. Keep in mind that this was somewhat of an experiment. If or when it falls apart I'll make another one with better materials. I can't remember how long it took me to build, but because I filmed the whole process it took a lot longer than it would if I wasn't making a KZfaq video. Thanks for the comments.
@joaoluis17442 жыл бұрын
muito fixe
@BigFatTonys5 жыл бұрын
I have seen three designs for adjusting the height of this jig; crossed arms, opposing wedges and spacers (seen here). has anyone tried all three ?
@ejtakach7 жыл бұрын
Not sure how the last spacers that set the height of the slotted sides control the final thickness of the workpiece. The plane seems to be captured by the slotted sides, but the thickness is set by running the plane on the inner, permanent rails.
@craigperry99187 жыл бұрын
when drilling the threads what size and fine or coarse
@MartyBacke7 жыл бұрын
I used 10-32 screws.
@dpmeyer48672 жыл бұрын
nice
@jasonb43507 жыл бұрын
Your drill press sounds like an engine that spun a bearing
@jbidinger3 жыл бұрын
I could have used this earlier today.
@owenpeter37 жыл бұрын
I went to sleep about half-way through this. Ended up nice though.
@MartyBacke7 жыл бұрын
Thanks for the compliment, I guess.
@Ratimus_4 жыл бұрын
4:56 must be Gallifreyan poplar
@mikes13304 жыл бұрын
what's the mini plane you are using @ about 2:31?
@MartyBacke4 жыл бұрын
That's an early 20th century block plane. Lie-Nielson makes a modern version: www.lie-nielsen.com/products/violin-makers-plane?path=block-planes&node=4072
@rogermartin79427 жыл бұрын
youtube tournage sur bois
@johntaylor13594 жыл бұрын
Wow that big red blade scares me. Why use it to cut to length when a hand saw would be so easy and totally safe plus you have a good plane why not use to reduce width John uk
@MartyBacke4 жыл бұрын
There's a million ways to do anything. This is how I did it on that given day.
@Jeff0343 жыл бұрын
No riving knife. Just a matter of time.....
@MartyBacke3 жыл бұрын
LOL
@ermirr84143 жыл бұрын
The jig is nice, but you use a lot of machines to make what could be done in easier (and safer) ways with simple tools that everybody has.
@MartyBacke3 жыл бұрын
There's a million ways of doing anything. This is how I choose to do it.
@ermirr84143 жыл бұрын
@@MartyBacke Of course there are and it is clear this is how you choose to do it. But using a drill press on a poorly supported beam is bad practise safety-wise. In your case, that hole does not need to be precisely perpendicular and, considering how you hold the piece, it probably didn't come out perpendicular.
@MrHeavyParty7 жыл бұрын
Yo, your drill press is shakier than Michael J. Fox...
@MartyBacke7 жыл бұрын
Funny. It's not a machinist drill press that's for sure. The vibration is coming from the belt which hasn't worn in yet. So far it hasn't got in the way of how I use it.
@thomasarussellsr7 жыл бұрын
Not cool, dude. If his shakiness were do to some self inflicted issue, like alcohol use it would be funny, but to use someone as a joke for a disease they con not control is pretty petty. However, yes the drill press is quite shaky.
@jasonb43507 жыл бұрын
Thomas Russell I agree with you after reading that comment I was twisted some people are just mean and that guy needs a good ass whooping and I would be happy to deliver it