Making a Speed/Power Test Grid and Engraving Powder Coated Tumblers with XCS

No video

Making a Speed/Power Test Grid and Engraving Powder Coated Tumblers with XCS

Рет қаралды 8,683

Күн бұрын

In this video, we learn how to make our own speed / power test grid in XCS and engrave a couple of tumblers.
www.panhandlel...
Melamine Sponges: amzn.to/3ZTmEfM
Tumblers: amzn.to/3l6hSwM and amzn.to/3LkEsN3
Xtool D1 10W Diode Laser: amzn.to/3ktDzGW
Dragon SVG: www.etsy.com/l...
My Etsy page: etsy.com/shop/...
Connect with me:
Facebook: / lasernoob
Discord: / discord
Instagram: @thelasernoob

Пікірлер: 28

@Gunner7261 Жыл бұрын

Your tips were gold Shipmate!

@rejetenchavez2037 7 ай бұрын

You sir saved my project! Big Shoutout!!!

@LaserNoob 7 ай бұрын

Glad I could help you out!!

@RNMEDIC1335 8 ай бұрын

Great video. Thank you for your service.

@stunt509 3 ай бұрын

Would it not do the test correctly if you would have united the full array?

@rudygomez6511 Жыл бұрын

Thanks so much for the video, it was incredibly helpful. I'm curious, if you don't mind, after finishing with the power/speed grid, did you use a different tumbler or did i miss something there?

@LaserNoob Жыл бұрын

Yes. I always waste a tumbler to do a test. The actual design was a different tumbler. Once I've done the test, I won't run it again unless it's a different brand or color.

@rolandoflores4948 6 ай бұрын

That’s was a really nice video But how do u center the laser to start the project my xtool d1 pro 20w starts at another position not even close to where I have my tumbler I use user origin

@LaserNoob 6 ай бұрын

Here is a video that goes over a very easy way of centering. kzfaq.info/get/bejne/gqiZYMR_3Ja5XYE.html

@bradnewman1821 10 ай бұрын

Great video thanks mate. Are you using air assist? I have a d1 pro 20w. Do settings need to be changed per tumbler brand as I will be doing YETI although they are expensive to be using for test pieces

@LaserNoob 10 ай бұрын

I don't use air assist on tumblers. Your settings will also be different with a 20w. Sadly, the best way to get your settings dialed in are doing a speed/power tests on each different brand and color. Some brands may have thicker or thinner powder coats. I do find that on my 10w, 100% @ 70mm/s works for most. But not all.

@bradnewman1821 10 ай бұрын

@@LaserNoob thanks for the tips. I have setup a test grid with the same parameters as your 10W and will see how that comes out. Cheers all the way from Australia

@rinalopez56 9 ай бұрын

How to you avoid black smoke marks or brown yellowish burn marks on the white cups

@LaserNoob 9 ай бұрын

A combo of things could cause that. Improper focus, need for air assist or perhaps speed to slow. I have not had that issue on any color of tumblers.

@larrycolson7451 Жыл бұрын

Ryan, when doing the White tumblers on the 20 watt machine, what settings have you gotten the best results? Also, are the tumblers you are doing with these settings Yeti, or Rtic, or Amazon No-Names? I'm using 80 mm/s, 60.0 %, Overscan ON @ 4.0%, and 180.0 LPI, and Constant Pwr Mode ON on White Rtic Tumblers. Are we close for the White?

@LaserNoob Жыл бұрын

The skinny tumblers are from Amazon (links in the description), but work very well. I don't have a 20w. Just a 10 and 5w. But with a 10w usually 90-100% power and 50-70 mm/s. I do a speed / power test for each color and each brand as the setting usually vary slightly.

@headstrong6523 3 ай бұрын

What was your LPI?

@LaserNoob 3 ай бұрын

Minimum 220 lpi.

@purplepenguina.k.a.burlyma6845 Жыл бұрын

Ok question. With my Xtool when I'm using my rotary it doesn't seem to increase speed above like 50mm/s. I have changed the values many times but it doesn't go faster. Even the gantry itself goes slow. Any idea what would cause that?

@LaserNoob Жыл бұрын

Can you take a pic of your settings and dm me on Facebook Messenger? Or join my discord server if you have that option available to you.

@purplepenguina.k.a.burlyma6845 Жыл бұрын

@@LaserNoob I am running a tumbler currently but yes I will send you a pic with my normal settings. Currently doing 80 power and 100 speed and this one is slow because I'm going for photo realistic as it's a pic of my son and his cousin for my mom. So the lpi is set at 300 which I know slow the process down but left to right is super slow too

@LaserNoob Жыл бұрын

Are you running xcs or lightburn?

@purplepenguina.k.a.burlyma6845 Жыл бұрын

@@LaserNoob xcs. Currently poor so going with free program

@LaserNoob Жыл бұрын

No judgement here! I pinch pennies wherever I get the chance!

@georgeblank2648 10 ай бұрын

Upgrade the software and you'll see a material test grid already done

@LaserNoob 10 ай бұрын

2 things. 1) Six months after I made the video, you assume I haven't upgraded the software? 2) It is important for people to familiarize themselves with the software. This is a good exercise for just that purpose, regardless of any "easy way" software update. Thanks for your super important information though.........

@VitiatedsHOWTO 9 ай бұрын

@100%p-30-/s I get blue

@LaserNoob 8 ай бұрын

That's pretty high power for that speed. Depending on speed and power and what laser you are using, you can easily color stainless steel and get reds, yellows and blues.