Making a Twin Cylinder Solenoid Engine

Рет қаралды 29,374

Maciej Nowak Projects

8 ай бұрын

/ mn.projects
Making a Solenoid Engine with two cylinders and much better control than a mechanical switch.

Пікірлер: 34

@neal_laugman 8 ай бұрын

Very clever! You are quite the craftsman.

@MCsCreations 8 ай бұрын

Stunning work, Maciej! Really well done!!! 😃 Stay safe there with your family! 🖖😊

@elsoda92 8 ай бұрын

es demasiado relajante estos videos, gracias

@rdyer8764 8 ай бұрын

Great project and great video and editing!

@AnthonyCurreri 8 ай бұрын

Love your projects. Totally fascinating

@MASI_forging 8 ай бұрын

Great work as always 👍👍

@hacerclic1020 7 ай бұрын

Nice work!

@vinceianni4026 8 ай бұрын

Good job mister well done

@sportsman1824 8 ай бұрын

Always creative

@rickpalechuk4411 8 ай бұрын

Neat Thanks for sharing Cheers

@demoleon4922 5 ай бұрын

Cześć Maciej, czy można przerobić generator benzynowy na generator wodorowy? Z góry dzięki za odpowiedź.

@philipwalton4877 8 ай бұрын

Your next project should be the Tesla Valve.. look it up.. I think you would nail it

@h7opolo 8 ай бұрын

i like it a lot

@jesuslovesyou5819 8 ай бұрын

What are you planning to do with that?

@VEEZER1 8 ай бұрын

Your mom

@kreynolds1123 7 ай бұрын

As is, there's no way to pull power off the shaft, so that means it sits on the shelf as a demonstration of concept, after having used it while making a KZfaq video to earn money for the video creator.

@kreynolds1123 7 ай бұрын

Attractive and demonstrate the concept well. But winding coils on an aluminum core acts like a 1 turn transformer. The induced currents in the core make their own magnetic field that opposes the magnetic field of the coil, and reduces the coil's inductance, and overall magnetic field. I'm saying you'll get better performance by replacing the core material with a nonconductive material like wood or a paper tube. You'll get higher inductance more magnetic field which would allow you to use fewer turns and suffer less resistive losses for the same work output. I propose that one take a dowl rod wax it. Then wrap it with paper and epoxy it to give it strength. Then add end caps And epoxy coat everything as you wind coil. Then remove the dowl. You can screw into the end caps to secure the coils in position.

@manishsingh8837 3 ай бұрын

Can you make a Multifunctoinal Full Motion Chair Clamping Keyboard Support Laptop Holder Mouse Pad for Compfortable Office and Game

@EfficientEnergyTransformations 8 ай бұрын

You can hugely improve efficiency of the engine incorporating Benjiman ( Benjamin ) R. TEAL's principle used in his Magnipulsion Engine ( MagnePulsion )

@king_james_official 6 ай бұрын

me off da penjamin

@vairen 8 ай бұрын

И зачем надо было ставить 2 оптических датчика? если магниты работают в противофазе! 1 ключ инвертора и вуаля. И место оптических датчиков можно было бы применить датчик холла

@jeffmccrea9347 7 ай бұрын

WOW!!! "6000" bearings on one little shaft. I'll bet it runs smooth but how did you fit them all on one little shaft??? 🤣🤣 Seriously though, impressive.

@GONZODIGITALSOLDIER-mo4tl 7 ай бұрын

cool!

@_Darling_Senpai__ 8 ай бұрын

❤❤❤

@piconano 8 ай бұрын

Love your workmanship. Why is it so wimpy? If you glue a circular neo magnet to the top of the piston, make a multi-layer pancake style coil (Tesla patent # US512340A) and place on top of the cylinder block ( where you have the rings), you can make it a beast of an electric engine. I was infatuated with pulse motors from 1998-2004 and made many version. One of them was what I just described. Amazing torque and efficiency. Timing needs to be controlled by an Arduino or something. I used a Basic Stamp and PIC as my goto microcontrollers at the time. Also, do not use aluminum. It's diamagnetic and messes with the field. Use brass instead. I made everything out of brass using my crappy harbour freight micro-lathe. When the cylinder is top dead centre, the coil is pulsed and will oppose the magnet, which pushes the cylinder with a strong impulse, which will get transferred to the flywheel. Another trick, was to use a 1A schottky diode across the mosfet and charge the main capacitor bank. I got about 80% of the energy back this way. You can even use it as a generator or short the coils to bring the engine to a dead stop faster than you can say "holly macro"!

@nedimbuyukafsar6434 8 ай бұрын

👍👍👍

@SteveBlack-kj3pm 8 ай бұрын

Puedes hacer esto en un motor de un automovil ??

@scottyno03 8 ай бұрын

Sure! If you want something super inefficient.

@christiansoldier1547 8 ай бұрын

Build this, And inverted water wheel. A wheel that is put into a tank of water. Bellows bags are used to lift one side of the wheel and the bag at top position gets squeezed and the air escapes through a pipe to the adjacent bellows bag at the bottom.. A locking mechanism around one o'clock position then unlocked at five . Begin squeeze about eleven o'clock position. The bellows bags will have asked board on top of the bag that hinges shut and will have two rollers on top so it closes as it turns. This device uses no fuel at all. Only air bubbles to lift and enough of them tonight pushing the top one through the squeeze chute to load bag at bottom. P.S. I am the original inventor of this device and I have described it in length on radio station twice and gave extensive description on air. That's means that it is not longer eligible to be patented. So it's free to the world. Enjoy.

@DetroitFettyghost 8 ай бұрын

You invented it but have you ever built it? It would be a shame if you never got a chance to if you haven't and I hope that happens for you. .much love bro

@christiansoldier1547 8 ай бұрын

@@DetroitFettyghost Mine is heating my house with a copper pressure plate in a woodstove filled with sand. The shaft from the inverted water wheel drives it.the opposite end of that shaft is geared to drive my battery bank charger.