Dave, you are a great instructor! I just found your channel and I enjoy the welding and especially the template layouts. Keep them coming!!

Exactly what I was looking for. I followed along step by step and my 30 degree template looks exactly right. We'll find out in the morning! Thanks

Good stuff. Searched all over to find a template to do a 45° saddle. You're video worked great. Did the drawing on AutoCad with no problems.

Thanks, exactly what I was looking for. I want to make a rocket stove using round pipe. I remember doing similar drawings when I was in high school a long long time ago but couldn't remember how to set it up. I didn't understand why you were using the inside diameter at first but then I figured out that it must be because its the inside diameter that contacts the other pipe

I love these videos... never had a chance tp learn anything like this .. thank you ...thank you..

Thank you, very helpful. Should be able to use this in the field.

Just Ready for the Practical, thanks for reminding us hope for the reality soon.

Thanks a lot sir for sharing your knowledge !!!

Yeah,Dave is actually a gr8 instructor

Thank you. This is very helpful.

Lost in space at 13 minutes. I can relate to that. We have contractors who think outside the box and then you have what we call in Australia he cowboys. Well, I'd say 90percent of construction is cowboys. Great video thanks for spending your time doing this.

Great video - thanks very much

Your awesome boss!

Like your work

Good job bro!,same my vlog about ducting from philipines

You are so the Very Bst , to me, for lo g Dave!

Thank you sir!

really enjoyed your video and I appreciate the time you spend on making thus video. But i keep wandering, does this technique also work when the 3 inch pipe is off centre ?

Nice thanks

Thank you so much for this tutorial, very well explained. Do you know if any significant changes are needed for making a sheet metal "Y" I'm thinking for dust collector piping.

Are you able to make a video about symmetrical two plate WYE branch? It is a very interesting and complicated topic.

Dave where did you get that compass? I have been trying to find one.

At a little over 5 minutes you mentioned you don't have to have advanced degrees in trigonometry to do this. That makes me think about the Giza pyramid built some 12,000 years ago or more. Architects and engineers still use the concept for their designs and mentioned they would be happy if their work was half as good. Certainly the level of accuracy in the megalithic structures goes beyond what we are able to achieve today. I'm in awe. Recently the British took some high level equipment to Egypt. They had ultrasonic instruments that could record what is underground also measure for straightness on each level of 60 tonne limestone blocks laid. What they found out was there was only a slight deviation from one end to the other. What they did fail to mentioned was the deviation was to the same scale in relation to the curvature of the earth. Let that sink in for a little. I just don't know why the conformed narration wants to keep this from the public.

you may have mentioned this already but will this technique work with any angle

Can you do a video doing a layout for a saddle going to a 90 degree elbolw. Making a dummy leg for and elbow.

Hi Dave could u please post a video about how to lay out an 10"×14"square to 8" round 7" high.

Hey I do sheet metal fabrication for insulation on piping would this method work ??

Do you have any drawings of projection of an L joint at 45°

Thank u

Any chance you could do a demo on layout for a coal bucket?

12:48 what's the name of the course? I'd be really interested in taking a course like this one.

Hi Dave,I love your account and appreciate the time you put into it.i could do with knowing how to make a template for a hole that is off set on a vessel say a 6" connection to a 32" body but off centre.be great if you could show that sometime soon.cant find a video on here about that.many thanks

Sir please upload video of pipe to fastrum of cone with an inclination agle of 45deg. Also please provide development /flat pattern of cone with hole pattern and how to marking in a plate.

I'm confused to why you say you have to use the ID or it won't fit. I think you should use the OD but then you have to bevel the inside. Right?

Sir I need oval to sqear making vedio please

I used to hate graphic communication at college, much better watching someone else do it

Dibagi 16.bagaimana cara membaginya Pak , saya tidak lihat karna jangkanya tertutup tangan Bapak. Mantap. tapi kalau bisa sekalin bikin mall induknya(risernya) pak. Trima kasih

Wowwwwwwwwwwwwwww

7:43 confused the shit out of me lol idk what to do from this point forward

Hello good video but we watching it because we need to know how to do it, can you show each point and not jump thank you [ A, B, C ]

With due respect..I drew...

really enjoyed your video and I appreciate the time you spend on making thus video. But i keep wandering, does this technique also work when the 3 inch pipe is off centre ?