You broke the world record for time spent holding a soldering iron to 18650 batteries.

the most amazingly dangerous build I have watched today. I have watched a lot of these lately lol

First off great video, you are the only one i could find that actually explains the process as your doing it. All the other knuckleheads have some god awful instrumental music playing the whole time without an talking telling you what to do and why. Thank you for making a truly informative video.

lol. and there I was worrying about overheating my cells. :)

Soldering battery with a professional iron, assembling battery without balancer, this man must be an expert at making IEDs 😎

cool video very precise as usual Antony

THANK YOU! Only video I could understand !

But you really need a balancer if you want to charge those things on a regular basis. If you don't balance than at one point you will be over charging one of your cells so far it might catch fire.

The best and safest way would be to use a 4 x battery holder, pre wired in series. Then take the cells out and charge individually in external charger when low. Otherwise you would need a BMS. Using cells in series is not a problem, but charging in series is.

Excellent demo

any idea how much volts/amps the tabbing wire can take, been looking everywhere to see if it worth using on a 36v ebike battery, just don`t think it will do unless i put on 3 layers or more

Keep up the good work 🎉🎉

Nice project 👍

Thank you very much I need to replace the batteries in an old drill Where do you got those cages? Muchas gracias amigo. S.A. Tx

hi Antony,Do you charge it without a charging leveler chip?

What kind of soldering Iron was that you were using?

sir can i ask what is the wire sized you used in battery?

Thanks for the video, very helpful! What are those black clips called and where could I buy them? Thanks again!

Is I make 1.2 volts 4 batteries together and recharge it?

can you do the same wity size 123A?

Red nick style electronics.. I Love as well.

Nice video. I'm wondering what you made that for. I'm sure this was ok and worked fine but others watching should not ever leave the iron on the battery for more than 2-3 seconds. It's usually ok with the better brands but a single cheap battery can absolutely blow up and ruin your day (maybe more). Those unbranded Chinese batteries are notoriously flimsy (when an actual battery and not filled with sand). 1. Get a hot iron and semi-sweet cloth ready 2. Clean and lightly sand/scratch the leads of the battery 3. Tap some solder onto the battery lead, taking no more than a couple seconds. 4. Immediately turn the battery over onto the wet cloth to cool. 5. Repeat. Again, it's usually quite safe but you have to remember that these batteries are mass-produced and some poor builds sneak out even from the decent manufacturers. Chinese batteries? Forget about it haha. No more than 2 seconds and get that iron off of it.

How are you gonna recharge them later?

thank you

OH THIS HELPED ME A LOT I CONNECTED 4 BATTERY'S IN A DIFFERENT WAY AND THE WIRE GOT TOO HOT AND SMOKE CAME 🤭

Did you print the holers with your 3D printer? Where do you get your flux from?

This battery can i use bajaj discover bick

Sir how to charge it

Hi Anthony. I want to build a power pack using Two sets of $cells in series like yours, but connect the packs together in parallel to double the mAh. Once I have done this how on earth do I charge the packs back up after use?

thank !

Nice video but please use lead solder.

Is it possible to bundle enough packs to start an auto engine? And if so how do you configure end up with a cable connection big enough? Got tons of these and tab and bus. How do u weed out bad cells, won't charge by by, hold charge, how to test?

could I put 12 of them together and make a 48 volt battery for my ebike?

You should have sand the battery top 1st before you solder i can see you are struggling with soldering

Don’t do what is shown here!! To much heat on cells no pre-soldering to cells no flat soldering tip forecast calls for damaging or worse. Also tin your soldering iron .

Demmmag nhi tere koooo

Thats messy

Damn, dude. You ought to learn the basics of soldering before you put out a KZfaq video about how to solder cells. That iron is way too small and you're killing the cells with excess heat.

If you all haven't seen a documentary called... It's worse than you think... By revelations of Jesus Christ ministries... I suggest you do... All praise and Lord to the most high Jesus Christ

Are you an electronics technician? I don't think so. You just tortured the batteries, man.. What if a teenage minor mimicked your style on these videos and ended up burning their home in the process?

Weak