Vídeo de como extrair vela incandescente partida, vídeo de como usara a respectiva ferramenta. Video of how to extract broken glow plug, video of how to use the respective tool.
Пікірлер: 154
@jaredandress43045 жыл бұрын
Honestly such a great video of how to remove these little buggers. Just got the kit and will be employing what I learned here. Watched like 25 videos that were good but this one it a real world video that most people will use.
@HERAS9003 жыл бұрын
same here 3 out of 4 snaped was dreading the bill till i saw this video
@badgern69232 жыл бұрын
How did it go?
@vadmalski2 жыл бұрын
Love videos with all needed info and no talking ! d
@Starlet_ep_4 жыл бұрын
Perfect video explanation will deffinatley buy one of these sets now thanks 😁
@markjohns79303 жыл бұрын
Just used same puller on a broken glow plug on a Vw golf worked a treat . tried a slide hammer before using this which did not work but this did . hooray 😀
@SteveRivett4 жыл бұрын
Great video, I would have put grease on the Tap before repairing the threads at the end.
@MarcoPereiraFerramenta-Online4 жыл бұрын
Ok, Thanks for the tip .
@elibradley74187 ай бұрын
Awesome teacher video i know now what to do with this kit as i just broke one on 6.6 liter duramax today
@Efferpheasants Жыл бұрын
Great simple video - no languages needed it is all there -thanks.
@MarcoPereiraFerramenta-Online Жыл бұрын
Thanks
@MarcoPereiraFerramenta-Online Жыл бұрын
Thanks
@viajero-cubano Жыл бұрын
Buen video ,donde se puede adquirir esa herramientas?,sería Ud tan amable de facilitarme el enlace. Saludos
@Pete8562 жыл бұрын
I just bought the same kit as shown here. One thing to be careful with is the 8mm and10mm taps in the kit have 1mm pitch threads which are finer than standard metric, my glow plugs are 10 x 1.25mm....luckily I already own the right tap. The other thing is the length of the glow plug, mine are quite short after the thread and there is a danger the stepped drill will cut the tip off the plug at the point I have drilled the threads out...I might stop short and use a different drill bit to finish the larger diameter hole.
@playsportfun33564 жыл бұрын
Great! Accept you have to tap the hole before you pull the tip so bits don't fall in the cylinder.
@mikek97786 ай бұрын
What do you mean by tap the hole?
@janmedricky96404 ай бұрын
@@mikek9778 Reshape the 10 mm thread before pulling out the broken plug.
@jp15483 жыл бұрын
Great, thanks. The kid had no instructions so you where a lifesaver. Had no clue how a right handed extractor was going to turn out the threaded portion? My only suggestion is make sure you don't just crank in the tap. you need to half turns and back up to break off the cut so the cuttings don't jam up the flutes of the tap. If this happens the tap will break off when it binds....then its head off for sure.
@MarcoPereiraFerramenta-Online3 жыл бұрын
Thanks 👍
@Crusaderfixer3 жыл бұрын
A left hand drill bit of the appropriate size is a must have for extracting broken right hand threaded anything. The heat and vibration will very often turn the thing right out, on the bit.
@lasseblomqvist93784 ай бұрын
@@CrusaderfixerDo you know of any extraction kits with a counter clockwise approach that you could recommend?
@paulelscey24654 жыл бұрын
Great video. I got set of transit plugs to try and get out after lunch which allways snap .not looking forward to getting the head of. Might see if the company will invest in one of these tools
@Gimpy1987VFR2 жыл бұрын
I found this out to my luck today. Snapped just above the thread
@nasokas3 жыл бұрын
Love the demonstration how it works, but just one question. When you where making threads at the end, doesn't it cause small metall bits to fall in? As far as I saw other people make thread's before pulling out the glow plug. Or there ar no is no small bits left when you remake threads?
@MarcoPereiraFerramenta-Online3 жыл бұрын
Yes, this can happen, but without removing the broken glow plug, You do not get the thread open correctly , the thread opener must be lubricated with grease,so the filings tend to stick to the tool . And there is less likely to fall into the engine .
@javiercuautle8215 Жыл бұрын
Que número tiene la caja para pedirla
@eedom6911 ай бұрын
@@MarcoPereiraFerramenta-Online Do extractors ever work? 1 out of 8 broke and I've been trying for days to get the last one out which broke at the hex near threads. Tried 3 different extractors so far. The hole left by extractors has grown and probably too big for this. Thought about trying to thread the hole and screw a bolt and nut in like double nut method which looks kinda like this right???.... but getting closer to threads. Been trying heat, oil, and as of today citric acid spray.
@jackrees53252 жыл бұрын
Any tips on removing the glow plugs boys and girls I have atleast one that's snapped so far (by previous owner) and need to replace all of them
@fixitfrank17525 жыл бұрын
Good video but one problem .repair with the tap before removing the old glow plug to avoid Metal fillings from going into the Cylinder
@fixitfrank17525 жыл бұрын
Andy B hi Andy what I mean is to tap the cylinder head first then remove the old glow plug broken piece with the old plug in place when tapping the cylinder head no filings will go down into the bore .if this is not possible use grease on the tap cheers
@michaelfreeman73815 жыл бұрын
Wish I read your post first. Now I'm afraid to tap it for this reason.
@bernardstef5 жыл бұрын
Oh yeah, tap before removing the remainings of the old plug. Good advice thanks
@fixitfrank17525 жыл бұрын
Stéphane Bernard cheers good luck with the job
@bernardstef5 жыл бұрын
@@fixitfrank1752 Many thanks, trying this afternoon ;)
@rayanislam93933 жыл бұрын
Bon travail propre
@darrenclay98592 жыл бұрын
Great video well done
@MarcoPereiraFerramenta-Online2 жыл бұрын
Thanks.
@mohe81 Жыл бұрын
If it is only the sleeve thats stuck, does no metal fall into the engine when you drill?
@nomadsteve52973 жыл бұрын
You are a life saver, thank you
@alexgnom18753 жыл бұрын
Danke schön fürs Video
@ClipuriDiverse.213 ай бұрын
WOW !THE BEST MAN ! TKS !
@MarcoPereiraFerramenta-Online3 ай бұрын
Thanks.
@dylankelly79033 жыл бұрын
Make sure you get the engine good and hot before u remove them and should help from snapping
@armanifaysal27834 жыл бұрын
Perfect tools
@ardentizzy77202 жыл бұрын
Very interesting 👍👍👍
@vincentrolfe13842 жыл бұрын
at time 4:28 when you pulled out the broken end of the glow plug lost in the head; it was a thing of beauty!!!! Need I say more!
@MarcoPereiraFerramenta-Online2 жыл бұрын
👍
@eedom6911 ай бұрын
I am imagining that when I finally get it out. And hopefully don't destroy the threads or worse in the process. My glow plugs are on the side of the engine not like this one.
@alexanderstefanxandraswedi58352 жыл бұрын
Good job
@MarcoPereiraFerramenta-Online2 жыл бұрын
Thanks.
@jonathondavies8347 Жыл бұрын
to prevent locking up in future a bit of copper slip on the thread helps.
@crpth14 жыл бұрын
I'll leave my 2 cents, in the form of a warning! This particular kit DO NOT work on the PSA/Ford DV6 engine (i.e. 1.6 HDI or 1.6 TDCI) on cylinder no. 2! Remember no. 1 is on the clutch side. For the other cylinders I cannot comment, since I didn't test. But particularly on the no. 2 it won't work. At least not on the engine casting I tested. Peugeot 307 SW 2006, 1.6 HDI (HXC). All the procedures indicated for the tool various components work perfectly (drilling, tapping, etc)! BUT the problem is the extraction stage, as seen on 4:00. On this particular engine casting there's no space for the holding sleeve to rest against. As such the extractor pin (2:50) got bend, but the plug remain in place. Now slightly jammed... Extractor tool of the "sliding hammer" type, seem to be the perfect choice for this particular case. Since it don't rely on a saddle to rest the holding tool. That in this case is too small. Be aware. Cheers. Example on a DV6 (1.6 HDI) cylinder no. 1 kzfaq.info/get/bejne/hbh3YJRmt8y6mY0.html
@monkeytutz23 жыл бұрын
I have the same kit on order with Amazon for delivery tomorrow. Typically the last glow plug snapped, even after cracking them off with the engine hot and leaving them to soak loose with penetrating oil overnight
@mohe81 Жыл бұрын
How did it go? Could you save it with the tool?
@monkeytutz2 Жыл бұрын
@@mohe81 Yes! The kit worked well. I only had one to drill out and the stepped drill bit snapped the tip off just as it broke through. When I went to try and pick out the snapped tip I noticed the remaining threads were loose and the whole lot screwed out
@marcoaurelio69412 жыл бұрын
boas de onde é?
@blakebiltwell53 жыл бұрын
Great video! Where did u buy the tool set?
@MarcoPereiraFerramenta-Online3 жыл бұрын
EBay
@blakebiltwell53 жыл бұрын
@@MarcoPereiraFerramenta-Online do u still remember the specific item?
@meanodustino95632 жыл бұрын
Dad got this kit. Drill bits don’t fit in supplied tool. 3 taps but you can only use 1 that works with the tool👍 this is a way to make people screw up. You get what you pay for…..🙄
@NBMedia89282 жыл бұрын
My plug has broken at the heater element which is stuck deep in the head, will this kit remove it?? The rest of the plug body came out easily
@MarcoPereiraFerramenta-Online2 жыл бұрын
No web the plug breaks at the hater element You need another tool kit not this.
@lewisjasper78083 жыл бұрын
Mine is slightly different. My glow plug has come out with the full thread but it has left the casing inside the head. So I’ve got no threads at all to drill out just the outer casing of the glow plug and electrode to get out. Should I skip the tapping of the head since there is no threads for me to remove and go straight to tapping the casing that has the tiny hole left where the glow plug rod was
@MarcoPereiraFerramenta-Online3 жыл бұрын
When the preheat plug breaks in that area, you need another type of tool, other than this one. But it is almost done in the same way but with another tool.
@richardwilletts37732 жыл бұрын
@@MarcoPereiraFerramenta-Online can you confirm an example of the different tool ? - I can see a tool to remove electrode tip but that’s all
@davidcart285 жыл бұрын
Will this kit remove the electrode end part
@MarcoPereiraFerramenta-Online5 жыл бұрын
Hello, this is only possible to remove the glow plug when it break up on the screw thread not on the electrode end part .
@MarcoPereiraFerramenta-Online4 жыл бұрын
@@zdenekraska1491 To remove the electrode part you need another type of tool .
@marinagastaldo8574 Жыл бұрын
hola,como consigo ese kit de herramientas,yo soy de bs as argentina me pasarían ñ como podría conseguirlas
@MarcoPereiraFerramenta-Online Жыл бұрын
Pesquisa no EBay.
@rickardwestling81318 ай бұрын
One could tap the threads in the block before tapping the plug and removing it. Then theres less risk of getting metal parts in cylinder
@alexandergerzen2517 Жыл бұрын
Thanks for the video.The glow plug on my MB E 300 D is 10 mm. but the thread is 12 mm. Will that work for me? Thanks.
@MarcoPereiraFerramenta-Online Жыл бұрын
Yes, I think this tool works for this car.
@alexandergerzen2517 Жыл бұрын
I mean will the kit work to pull out the broken glow plug?
@MarcoPereiraFerramenta-Online Жыл бұрын
If the glow plug is broken at the top as in the video, yes you can remove it, with this tool, if it is broken at the tip, that is with another type of tool.
@thetuesdaywhistler4 жыл бұрын
Failure to use a reaming tool to remove carbon deposits prior to inserting new plugs may result in poor plug performance, premature wear, or plug damage.
@michaelfreeman73815 жыл бұрын
It worked! I got thr glow plug out! But.. the new plug is spinning and wont catch the thread - any ideas?
@evanch1234565 жыл бұрын
Helicoil what did you end up doing?
@jakethesnake98604 жыл бұрын
That’s a bad ass camera!
@MarcoPereiraFerramenta-Online4 жыл бұрын
That's what we have, not everyone can have top cameras . You can see how the tool is used .
@jakethesnake98604 жыл бұрын
Marco Pereira i was saying it’s a very good camera as well as a good tool!
@riyastnr282 жыл бұрын
Pleace share tool link
@marcoscarneiro76334 жыл бұрын
Onde encontro esse ferramenta no Brasil?
@MarcoPereiraFerramenta-Online4 жыл бұрын
Eu sou de Portugal, e mandei vir pela Internet. Mas penso que aí no Brasil também deve encontrar isso na Internet .
@bradthelad25802 жыл бұрын
Dose this work 9n vauxhall insignias
@MarcoPereiraFerramenta-Online2 жыл бұрын
I think so !
@carterkirkland Жыл бұрын
Does this work on a lb7??? 12 mm socket fits on it
@MarcoPereiraFerramenta-Online Жыл бұрын
Excuse my ignorance but what is a Lb7?
@carterkirkland Жыл бұрын
6.6 l v8 duramax
@MarcoPereiraFerramenta-Online Жыл бұрын
@@carterkirkland In principle, it should not be possible, because this kit only comes with 8mm and 10mm measuring threads . You need to know what the thread size of the glow plug is .
@metaldoktor88622 жыл бұрын
Hi Marco is Good for Mercedes OM642 DE30 LA
@MarcoPereiraFerramenta-Online2 жыл бұрын
Hello ,yes I think it also gives for this engine.
@katherineaktas2325 Жыл бұрын
What is this kit call please?
@togbah54473 жыл бұрын
Como remover apenas a parte de porcelana num Mercedes c220 cdi?
@MarcoPereiraFerramenta-Online3 жыл бұрын
Boas isso se parti na porcelana tem de ser retirado com outro tipo de ferramenta .
@togbah54473 жыл бұрын
Marco Pereira E sabe qual é? Obrigado
@edwardsmith71602 жыл бұрын
Little confused on what tapping is can somebody help
@mauriziogiasan44113 жыл бұрын
bravissimo
@MarcoPereiraFerramenta-Online3 жыл бұрын
Thanks 👍
@corshamkebab20243 жыл бұрын
2:57 that black screw broken up inside the glow plug and I don’t know how to take out
@user-uu4qw3pr1r3 жыл бұрын
How did you remove the glow plug core ? I guess thats a must before the drilling
@MarcoPereiraFerramenta-Online3 жыл бұрын
Yes, you have to remove the interior core befor drilling . In this case it comes out alone with the top parte of the glow plug when the i has broken .As you can see right at the beginning of the video . When it doesn't come out it has to be drilled out with a tool that also comes in this toolkit but that I didn't have to use in this case .
@jogisbastelbude53543 жыл бұрын
Drill with Oil,and Special Grease vor Injektor and Glowplug
@bronkokulitscka88375 ай бұрын
Is there a Link to this stuff please ?
@MarcoPereiraFerramenta-Online5 ай бұрын
Try Ebay .
@jasonputtock4428 Жыл бұрын
have you ever done a broken injector bolt.????
@MarcoPereiraFerramenta-Online Жыл бұрын
I've never tried it on an injector bolt, but if the threads are the same size it should work too.
@jorgeestrella57214 жыл бұрын
excellent video !!! where can i buy one or is anyone avail to perform this service in Toronto Canada please , as my jeep dealer wants to pull the head off my wk 3.0 diesel for about 5K damage to my wallet ...RSVP ....thank you !!!
@MarcoPereiraFerramenta-Online4 жыл бұрын
This tool can be bought on many websites, like Ebay, Amazon and other websites on the internet.
@rodrigoguzman13793 жыл бұрын
What is the tool kit called?
@fabianmonticello46479 ай бұрын
Donde compro un kit
@MarcoPereiraFerramenta-Online9 ай бұрын
Comprei no EBay.
@markthompson11343 жыл бұрын
where do yo get the tool from
@MarcoPereiraFerramenta-Online3 жыл бұрын
EBay
@MarcoPereiraFerramenta-Online3 жыл бұрын
Search EBay there for a lot of choice .
@jamesceltic60118 ай бұрын
I have this unit. The first issue I faced was the removal of the centre electrode which was protruding out of the broken gloplug so cannot drill the glow plug. So to temove center electrode I took a 8 mm long bolt about 100 mm long and drilled a 5 mm hole in the center of the bolt about 4 mm deep and then drilled a 3 mm hole about 20 mm deep and tapped it . I tried to tread the bolt on to the electrode. Then pulled it however did not extract the electrode. I tried again with a drop of tec 7 super glue. It worked the first time. Now I have the body of the extraction tool wedged over the glow plug area and can not remove it.
@LaLa-yp6dk3 жыл бұрын
My 2020 sprinter has been in the shop more than on the road 😰
@bedford19414 жыл бұрын
.35 second wear yours pulled out mine snapped off flush and now stuck
@MarcoPereiraFerramenta-Online4 жыл бұрын
The work is done in the same way .
@vincentrolfe13842 жыл бұрын
Let's all meet down at the local pub; I'm buying!!
@MarcoPereiraFerramenta-Online2 жыл бұрын
👍
@bernardcorbally6555 Жыл бұрын
iam a bit confused as to how he drilled out the treads from the top of the glow plug, then he retreads ,but does not put in a tap ,can any one explain how he just made new treads and puts in glow plug .
@MarcoPereiraFerramenta-Online Жыл бұрын
Threads are not opened in the engine head, but in the rest of the broken glow plug that is there.
@alfaomega1264 жыл бұрын
Opel ?
@MarcoPereiraFerramenta-Online4 жыл бұрын
Sim, 1.7DTi .
@43_amaljose442 жыл бұрын
Am from kerala, please share tool link
@riyastnr282 жыл бұрын
Please share tool link
@SuperRhysevans Жыл бұрын
No good if you don't have a straight line of sight to the plug..
@Tony-fh2wi3 жыл бұрын
O problemas é cair limalhas para o cilindro e depois kaput....lá se vai o cilindro!
@MarcoPereiraFerramenta-Online3 жыл бұрын
Sim, se cair limalhas pode vir a danificar, mas tem de ser feito com muito cuidado, para minimizar isso ao mínimo.
@jfjj26214 жыл бұрын
Copper grease !!
@agentcarbunkle3 жыл бұрын
don't use copper grease. The electricity going through the glowplug can react with the copper grease and cause it to seize in even worse! Use a ceramic grease especially for this purpose like Liqui Moly 3381 Pro-Line Injector and Glow Plug Grease
@adamnugent-cn4dy5 ай бұрын
Looks abit complicated
@MarcoPereiraFerramenta-Online5 ай бұрын
It's not complicated, it has to be done carefully. It's easier or more difficult depending on the car.
@GP-0073 жыл бұрын
Dont buy this thing is a very poor quality And you have to drill very straight
@MarcoPereiraFerramenta-Online3 жыл бұрын
The quality of the tool, depends on what You buy, yes it is always ones with more or less quality but with anybody you have to always drill straight .
@GP-0073 жыл бұрын
@@MarcoPereiraFerramenta-Online It was very helpfull to have a tool to help to drill straight Thanks for reply .
@GurpreetsinghKaka-su3fo6 ай бұрын
Parje
@TheMrsaintevil Жыл бұрын
Why Glow plugs have such a stupid design?
@MarcoPereiraFerramenta-Online Жыл бұрын
It's what we have, and we have to live with it.
@sweetnandito2 жыл бұрын
If it isn`t SNAP ON brand tools, it will snap inside, making it worse.
@MarcoPereiraFerramenta-Online2 жыл бұрын
This isn't from Snap-On, and I've taken out several spark plugs with it and it's still working fine.
@RajibDas-rs1og2 ай бұрын
Air tools mujhe chahie tha kaise milega boliye contact number bhi dijiye