Marquee Numbers | How to build

Marquee Numbers | How to build | Short version

Рет қаралды 28,301

Күн бұрын

In this video I explain my process for building 4' tall (50.25" with frame and base) marquee numbers.
I use 3/4" plywood and one number uses roughly 75% of a full sheet however all numbers will obviously vary.
Products:
20 Count Outdoor String Lights: www.walmart.com/ip/Better-Hom...
Tools:
Kreg Accu Cut: www.homedepot.com/p/Kreg-48-i...
Kreg Rip Cut: www.homedepot.com/p/Kreg-24-i...
13/16" Forstner Bit: www.woodcraft.com/products/wo...
Music found at www.epidemicsound.com (subscription required)

Пікірлер: 33

@snatson7992 Жыл бұрын

Beautiful made!!❤

@amandaramos7672 Жыл бұрын

Nice job

@thehooklessrapper 10 ай бұрын

Thank you!

@TheWeshub1971 5 ай бұрын

How tall are the side pieces that frame the number? And how much space do you leave on the back? One inch?

@twisteddesignco 5 ай бұрын

The sides are 6” and yes I leave 1” on the back

@ballonim Жыл бұрын

Hello from Germany, i like your video. You mix the filler with water to fill it in the bottel. How many water you use? Thanks Gabriel

@twisteddesignco Жыл бұрын

I use just enough to thin the filler without it being to watery however I have since started using white caulking

@sayauntataylor6760 Жыл бұрын

would like to know if you sell them , if so how much

@fernando75ful 6 ай бұрын

What angle do you leave in the corners?

@cesarvalencia648 Жыл бұрын

What size hole did you use for the lights

@twisteddesignco Жыл бұрын

I use a 13/16” Forstner bit, it’s the perfect size for the socket. This is the size I use for these lights

@mrobertaw68 Жыл бұрын

Nice job do you sell and ship them? If so how much?

@twisteddesignco Жыл бұрын

My apologies for the terrible response time, I currently am not shipping these due to the cost being through the roof.

@darrylfoster5623 2 ай бұрын

How long did it take you to make a single marquee number?

@CWills6385 Жыл бұрын

Just made a 16 for my daughters party. How much do you rent them for?

@twisteddesignco Жыл бұрын

I rent the 4’ Marquees for $98 each

@its_marc 4 ай бұрын

@@twisteddesigncohow long is that rental for?

@sondrastanley7230 4 ай бұрын

Which drill bit did you used to drill the holes?

@twisteddesignco 4 ай бұрын

With these lights which are the Better Homes and Garden 20ct from Walmart I use a 13/16” forstner bit, you can order one online or purchase them at a woodworking supplier like Rockler or Woodcraft

@sondrastanley7230 4 ай бұрын

What are you using to lift the number from the table when glueing the sides on?

@twisteddesignco 4 ай бұрын

@@sondrastanley7230 I cut 1” strips and place the underneath to get a 1” lip on the back side

@sondrastanley7230 4 ай бұрын

@@twisteddesignco thank so much

@davisharogers7447 Жыл бұрын

Can you give measurements for the base

@twisteddesignco Жыл бұрын

The base is 18” front to back, the width is usually only a couple inches wider then the marquee bottom which can vary

@davisharogers7447 Жыл бұрын

@@twisteddesignco thanks for responding

@chrismartinez5379 Жыл бұрын

Can you share link for the lights?

@twisteddesignco Жыл бұрын

I use the better homes and garden 20ct string lights from Walmart

@chrismartinez5379 Жыл бұрын

Thanks brother, appreciate it

@CWills6385 Жыл бұрын

@@twisteddesigncothat’s what I used as well.

@secerealwilliams2018 Жыл бұрын

What kind of wood filler do you use?

@twisteddesignco Жыл бұрын

I was using DAP Plastiwood filler but I have now started using white caulking to fill all the seems because it is much faster.

@torijeschke2273 11 ай бұрын

About how much does this weigh?

@twisteddesignco 10 ай бұрын

If I remember correctly they are around 30-35lbs