I didn’t buy this crash bar from bung king but I did buy a crash bar and using the tutorial and guidance from this video I was able to put a crash bar on my 2020 fxlrs . I am so pumped now and I don’t think I could have done it without the help from this video. Also this guy is fun to watch seems genuine and his vids are on point
@rollinreaper2 жыл бұрын
Ok so I put mine on today (2022 lowrider S) and couple of comments I’d like to mention. On the master cylinder side there are 5 holes when you remove the entire assembly and there were also five holes on that side of the crash bar for the bolts. You could only use 4 however because one of them is completely covered by the master cylinder housing and if you were to put a boat there it would impede on the back of the cylinder. I would also recommend to anybody doing this besides having a second person is to just lightly thread 2 of the bolts on one side and 2 on the other to get it situated. I learned the hard way after I got almost all of them in except one on the master cylinder side that was not lining up with the threads and had to loosen all of the bolts which sucked because I used blue thread locker. Regarding the possibility of stripping the bolts, wasn’t sure if you were referring to the removal or installation of the new ones. I had no issues removing but on that one near master cylinder (stock long torque head bolt) I almost stripped it bc the bit slipped inside of it. This isn’t a jab at your video but I figured I would offer this advice for all of KZfaq land because nobody else has videos on the installation of this bar that speaks of everything I just mentioned. Truth be told I probably would’ve just paid my local HD dealer for an hours worth of labor to avoid the frustration. I don’t have a bike lift or similar. Was a pain in the ass on the shift linkage side bc of it sitting low….I guess you did yours the same haha.
@waydel1 Жыл бұрын
Makes a great highway peg also ✊
@THEHEADLESSBIKER4 жыл бұрын
I use it on the highway all the time!!! Welcome to the bung king fam !!
@MK87_4 жыл бұрын
🤘🏽😎
@vitoraimondi26264 жыл бұрын
Pure awesomeness - looks sick. Another great install video - thank you!
@MK87_4 жыл бұрын
😎👍🏽
@prolife80794 жыл бұрын
bungking products are awsome, this crashbar fits nicely on the lowrider S, but be sure to use locktite on the bolts 👌
@MK87_4 жыл бұрын
Thank you
@anthonyr5873 жыл бұрын
I just bought these bars and have no idea what loctite is, is there some information on how to use this and which type to get?
@cheyenneobregon1843 жыл бұрын
@@anthonyr587 blue loctie from autozone or advanced auto and you google a video on how to apply loctie or read the bottle
@bungkingofficial89533 жыл бұрын
Hell yeah brother i work for bungking cool to see our products on KZfaq 💪
@MK87_3 жыл бұрын
Tell your people that a lot I got a lot of my friends and subs using your product lol. Amazing stuff!
@BikesBeardsAndBrews3 жыл бұрын
Totally saw that Wolverine tattoo! Hell yeah!
@MK87_3 жыл бұрын
Yea that’s my fav marvel character
@BikesBeardsAndBrews3 жыл бұрын
@@MK87_ BUT! who's your favorite artist drawing him and whats your favorite version of his costume?
@MK87_3 жыл бұрын
Probably Frank Miller
@drainmonkeys385 Жыл бұрын
These outta come with a chin spoiler, engine guard plate, going all the way the frame
@michaelwagner27772 жыл бұрын
Perfect brother!!! Appreciate your help with this one.
@magickgray4 жыл бұрын
Not sure if you did it off cam but you should use some threadlocker on those bolts. Nice video!
@andrews66512 жыл бұрын
noticed that too I installed my with blue thread lock today on the bolts
@ericbennett29864 жыл бұрын
Another great video. Looks awesome on the bike.
@MK87_4 жыл бұрын
Thanks bro
@davidpayne88984 жыл бұрын
Looking good bro. I went for the Moustache crash bar as I wanted to put some extra lights on them.
@chrissmith76693 жыл бұрын
I’ve got the mustache bars on my Bob. I don’t like the feet forward position so I stuck a couple yellow n black “ no step “ stickers on them. Doesn’t really fit the roadster cafe look but if it saves me from the scratches and dents I’m fine with the sacrifice. I’m putting on the slider passenger pegs as well.
@EasyRiderGreg4 жыл бұрын
Looks good! Ride safe, stay healthy.
@christopherjoos14543 жыл бұрын
What poundage did you use on the torque wrench?
@chadrickgregory13802 жыл бұрын
What is the torque specs for the bolts?
@MrKingKannibal3 ай бұрын
Nice content! what the is lenght of the crash bar?
@twistieslayer35924 жыл бұрын
Looking good.
@MK87_4 жыл бұрын
thanks
@jbones212117 күн бұрын
Thanks for the vid. Can ask how tall you are? I heard short guys like me 5’6” can’t reach the OEM Mustache guard so I’m looking for an alternative. This might be the winner.
@MacRides1 Жыл бұрын
i like it - looks great and protection great idea too. do they work as highway footpegs to stretch out on long rides ?
@joshkuk82795 күн бұрын
What fairing was that ?
@Turtle665 Жыл бұрын
Love the little rider by the way. Question from the video the crash bar just looks really low and wide? How does it affect your turning? Do you scrape or is it not a problem?
@dgonzala4 ай бұрын
I notice this crash bar sits low, does this affect your lean angle?
@erikmorales76123 жыл бұрын
Yo, great install man! I'm getting the same crash bar tomorrow. Where did you find the torque spec?
@assault_skateboards4 жыл бұрын
My feet kept slipping at high speeds, so I put some mob grip on it and it helped big time.😁
@DaveSmith-og7lf2 жыл бұрын
Try skate board tape
@goldpeaktm57664 жыл бұрын
Stay safe bro😘
@nickthinkpainting19782 жыл бұрын
Man I’m getting old 66 I could not break those foot peg torque bolts. Even with breaker bar and they strip very very easy so be careful. Pissed me off as it’s very easy install if you don’t strip those bolts or if you can break them lol.
@wildone14804 жыл бұрын
Hey bro that looks awesome. You think I can fit it over my speed merchant skid plate? Or maybe too tight of a fit?
@adriansegovia94134 жыл бұрын
Are you using the bung king with foward controls? I want one on my sporster but I don't want to give up foward controls???
@benmartinez45914 жыл бұрын
What size torx bit you use?
@DaveLeader2 жыл бұрын
45
@ad783 жыл бұрын
Get the rear bro they are cool! Although my front is the harley mustache
@reggiea.34872 жыл бұрын
suggest to blue loctite every bolts you took off.
@lastnline14 жыл бұрын
I knew you were going to need a extra set of hands but looks pretty easy
@MK87_4 жыл бұрын
yea the bar is pretty heavy
@eladiovelez27604 жыл бұрын
It definitely gives your bike that outlaw look as well as giving your bike some safety. Would like to ask you a question if I may. Now that you’re rocking a Memphis Shade where are you placing your ezpass. Might be a good video for you. Proper ezpass placement. 👍🏻
@chrissmith76693 жыл бұрын
I’m adding the Memphis shades fairing as well.
@MarcEstrella Жыл бұрын
Hey man do you actually feel your lean angle has been affected by the bars, I’ve heard people say that but the bike has to be leaned over so much for it to touch no?
@ironwarrior88903 жыл бұрын
I would use a smaller torque wrench on certain bolts..I've seen bolts stripped using them big mofos..oil drain plugs for one...if ya old skool you know the feeling by hand...if ya know you know..👌
@Turtle665 Жыл бұрын
And how does it affect You when you’re splitting lanes? Do you have to be careful are you not able to split such tight lanes?
@King_Moose2 жыл бұрын
MK- What are you torqing these bolts down to?. What number in ft lbs? Did you need a breaker bar to loosen theses bolts? My 22 LRS looks like it maybe a pain the ass.
@2kanchoo2 жыл бұрын
You scrape this bar at all around corners? I've heard of guys scraping this bar with the pegs that would be no bueno for me. Don't wanna lever the bike up on it around a curve. I wanted the high bar but it won't fit on 20+ without lowering the fork tubes 3/8 so it won't impact the fender under full compression.
@Everendlesss3 жыл бұрын
@Marvelkid87 I'm looking to upgrade to a LRS very soon. I'm looking at parts and definitely want some protection. I started riding on a Yamaha R3 and like to lean the bike over. Having started on such a light motorcycle, I am worried about scraping the engine guard you have installed. I see that Bung Kings makes a high version, but only for forward controls. What do you think?
@PepeDeezNutz Жыл бұрын
Can you test them for us please
@BigFlyingLoveMachine3 жыл бұрын
Hey boss did you tune it when you put the pipe on? I got the same setup on my same low rider s, but didn’t tune it so I can keep the warranty. Seems to be running great
@Crowbar3813 жыл бұрын
Can you feel that the pegs are now out wider? and I wonder how much the wider pegs reduces lean angle
@oruwatching4 жыл бұрын
I've thought about putting this on. I have one of those big chrome hop looking crash bars now. I am struggling to see how the Bungking would protect the tank if the bike was on its side. I can see that it would protect the engine. Thoughts anyone?
@jacobkidd2373 жыл бұрын
The bar ends protrude quite a bit and it prevents the tank from coming into contact with the ground. At least that's the idea. Not sure what clearance would look like towards the tail if you ever laid it down, but Bung King makes suspension mounted pegs for the rear for sporties, I'd imagine they offer something similar for softails.
@dhieyosandhu67904 жыл бұрын
Bikes looking awesome with bungking ... sissy bars next?
@hamiltoncross47083 жыл бұрын
About the rubber bolt inserts you take out, do they stick out too far to leave in? Is that what the instructions say?
@SomethingClever1013 жыл бұрын
dont you need a crash bar for the back as well? or like crash bar pegs?
@davidjpodurgiel73882 жыл бұрын
What pipes are those? Looking now for my Low Rider ST.
@FriedBalonyPony Жыл бұрын
Does anyone know if this will touch leaning into corners aggressively?
@KenseisGarage4 жыл бұрын
Like the bar, you still have mid controls. right?, I guess this one doesn’t work with forwards?, love the bike man, great video 👍
@MK87_4 жыл бұрын
Thanks and I’m not too sure if it will with forwards
@spencerb86094 жыл бұрын
They have one for forward controls
@raiderdad4life2153 жыл бұрын
Hi quick question. Did you use any locktite for this? Is it needed?
@CharlestonManchester Жыл бұрын
Anyone with issues threading the 4 long bolts for pedals? Doesn’t seem to screw flush.
@Blanchy1012 жыл бұрын
Any issues with this scraping or catching on turns?
@mikeessary49253 жыл бұрын
Hey bro, how are these for stretching your legs out on the highway?
@Skynet4k4 жыл бұрын
What camera do you use for the scenes your not riding?
@vivepopo4 жыл бұрын
No Loctite?!!!
@thesharky7354 жыл бұрын
Hey man, do I have any risers on your bike? If so how high and what kind?
@impalaa592 жыл бұрын
Where do you bought those crash bar?
@davidnewman48844 жыл бұрын
I have to put those on my street bob
@quicknarco85673 жыл бұрын
What size socket was that
@SMF7384 жыл бұрын
what windshield is that? and what size? thanks
@HDclubstyle3 жыл бұрын
hello what brand are the pedals?
@bv58533 жыл бұрын
Yo Marvel kid whats up finally going to put my bungking crash .question how much torque , i bought a torque wrench too.
@bv58533 жыл бұрын
*?
@edwardsabb173 жыл бұрын
Bro. Please tell me how you loosen your torx bolts without stripping it. Because these are completely AWFUL
@PkwyDrive134 жыл бұрын
Should have tipped it over to show how it works! Not like drop it, but set it down and show it off!
@MK87_4 жыл бұрын
That’s for the next video
@franciscodaschagasmendespe49904 жыл бұрын
muito bom!
@victorkelley50974 жыл бұрын
What torx size did you use to take the rear brake reservoir off?
@shiftlofi3 жыл бұрын
This!!! Still looking for an answer please
@victorkelley50973 жыл бұрын
@@shiftlofi Hah, I don't have much tools around the house so I just had the dealer put it on for me while I was getting a service done. They only charged me like 20 bucks.
@marcuseasley48082 жыл бұрын
Where did you get the front wind screen?!
@MK87_2 жыл бұрын
Memphis shades
@_S.E.J_4 жыл бұрын
Bro you need a oil guard on that front,
@dmetzke6352 жыл бұрын
What was the torque spec on that ? Anyone know.
@therealcountrybumpkin2 жыл бұрын
Yeah manual says 40-45 Ft pounds. And he didn’t install right, there’s 4 bolts on each side, not 3.
@charlie125904 жыл бұрын
Can you use them for highway pegs also?
@PkwyDrive134 жыл бұрын
Yes, and no...I had to put grip tape on mine cause it's pretty slippery otherwise
@MK87_4 жыл бұрын
Yes if your a tall rider and like he said if you put grip tape otherwise your going to slip
@davidss9094 жыл бұрын
Nice ! No passenger pegs ?
@MK87_4 жыл бұрын
Coming soon
@michaelcullen92164 жыл бұрын
@@MK87_ Going to use the Bungking passenger pegs for the crash protection or the factory passenger pegs so you can fold them out of the way?
@davidss9094 жыл бұрын
Been having those in mind or the fat bob passenger pegs
@davidss9094 жыл бұрын
Thinking bout rolling with bung king pegs tho
@chadcandiff48074 жыл бұрын
Are your bars stock height
@PkwyDrive134 жыл бұрын
Yeah his are stock... For now!
@MK87_4 жыл бұрын
Yea
@th33b332 жыл бұрын
Per Bung King 30ft lbs of torque
@briandrose4 жыл бұрын
Bro there's only one way to test out crash bars...