There is one really big misconception in this video that most 3D printing KZfaqrs make: The resin comes in 500g and 1000g bottles. That is nowhere near to 1l, depending on the resin. Check the datasheets. The Anycubic grey eco Resin, I mostly use, comes in densities ranging from 1.05 to 1.25g/ml. Based on experience, the resin is mostly in the 1.2x range of density. That means, the bottles contain a bit more than 800ml on average due to safety margins in filling, tending to overfill slightly.
@FauxHammerАй бұрын
Fine, fair enough.
@dennisstevens4347Ай бұрын
I got the Saturn 4 Ultra. I'm very happy with it. It has all the features I wanted. Worked right out of the box.
@HenrySavinonАй бұрын
did you have to calibrate it? I haven't and been printing fine out of the box but wonder id I should, It's a pain to clean just for test prints.
@leonardleyland8951Ай бұрын
Loving my Saturn 4 ultra. I did some calibration and ended up at 1.9sec using sunlu ABS like. Great prints and crazy fast.
@dennisstevens4347Ай бұрын
@@HenrySavinon Nope. I followed the instructions that came with it. I took the wrapping off, put in resin and started printing. I changed the settings in Chitubox to get the best results for the resin I'm using. I use Elegoo plant-based resin.
@aaronb1138Ай бұрын
Same. I get the price differential is 25% or 33% depending on which direction you're looking at it, but I do not understand why anyone would save $100 to lose the high speed print function, much less wifi print. That said with respect to people having issues with the etched build plate removal as mentioned in the video, they need to sharpen their putty knives, use wider putty knives, and keep the ground edge towards the model and the flat side flat to the plate in addition to fixing their bottom exposure times, bottom level counts, and adding in proper pre and after exposure pauses to the bottom layers.
@IgnusFastАй бұрын
Yes, PLEASE do the 3-to-4 comparison video! I'm still waffling on my first resin printer, and this would be helpful...
@OldSkullSoldierАй бұрын
I had recently the same problem and I bought S3. Why? Mainly because of that springy plate in S4 that makes a huge hassle of every cleaning of the plate. I change resin a lot between colours and I definitely don't want to stain my clear or white resin with black or grey. But if you plan to print 95% in one colour (e.g. grey) then S4 can be fine for you due to extra sensors. These are not needed, but they are here: you can clearly see if you are close to max level of resin and if you are empty, then just add some and that's it. And it's always good to filter your resin from time to time to remove broken supports if any and similar stuff. Especially after failed prints. Oh, and Elegoo offers stell funnels, there are fantastic reusable tools for resin printing.
@MaddnessCreationsАй бұрын
In the same boat right now, trying to figure which one I want the S3 ultra or the s4
@MERTisBESTАй бұрын
I'd love a 3 ultra Vs 4 ultra review!
@JohnJones-oy3mdАй бұрын
3:05 - Thumbs up for finding a way to incorporate Father Ted into a resin printer review. 👍
@pulsegategamingАй бұрын
There are so many printers out there! Elegoo has been pretty good to me Thanks for the review!
@tony-moraАй бұрын
The kettle remark sent me. lol
@BlueBirdGTVАй бұрын
Lmao i came here to add to the kettle comments 😂 I lost it
@NineTailedOtakuАй бұрын
As someone who's new to resin printing, I wanted to buy the Mars 5 but after seeing this and the 4 ultra video, I think I'll spend a little more and get the Saturn 4 Ultra
@FauxHammerАй бұрын
100% worth doing
@deadlyapolloАй бұрын
The "its stuck on too hard" was the very first thing i noticed about these 4 series. After testing, dropping from 30 seconds initial exposure down to 20 and from 8 initial layers to 5 solved this issue. From the factory, they really wanted to make sure that nothing comes off the plate......
@GeekDetourАй бұрын
Hi Ross! I would go for the Ultra too - period. I would also like the Green Lid on mine, the best color ever!
@TheBigGeordieGeekАй бұрын
The Green lid is amazing and I wish the Ultra had it! Also the kettle comment got me laughing!
@FauxHammerАй бұрын
So many people love the green. I expected people to hate it like they did with the phrozen S series
@rustumlaattoe10 күн бұрын
7:45 I laughed so hard it hurt.
@seanmyles2893Ай бұрын
hi ,Love ur work. I would like to see video comparing saturns 4 to saturns 3
@punk6119Ай бұрын
Love the green and would much rather have it on the ultra...
@FauxHammerАй бұрын
same
@j2ehypАй бұрын
@@FauxHammer Maybe they'll offer a replacement lid (with a handle!) someday. Doesn't seem like it'd be hard to swap out. ;)
@skylineg6618Ай бұрын
You are completely right. The "smoke" color with white accents is unquestionable eyesore on it's own, let alone if you compare it to an emerald green with black accents. It is the biggest reason to want the basic over the ultra, even over the cost.
@FauxHammerАй бұрын
Hahahah. I’ll assume sarcasm. But this is nicer
@Pretti-TrendyАй бұрын
Best review title of the year!
@FauxHammerАй бұрын
Hahahaha, will save a lot of people watching I guess
@lucaswiseman1259Ай бұрын
@@FauxHammer you make crystal clear prints by painting a layer of uncured resin over the prints then curing it. it's kinda janky and requires some finnese but you do get it like, REALLY clear.
@FauxHammerАй бұрын
@@lucaswiseman1259 yeah you can, I think i found a better way that retains the details..
@lucaswiseman1259Ай бұрын
@@FauxHammer oooh, cant wait
@ReadyMack-gАй бұрын
@@FauxHammer hi kind folk what is good source for elegoo resin settings
@RBallarddesignsАй бұрын
I am interested in resin printers but I don’t do miniatures. Could you do a video on practical things you can do with resin? Things that make more sense for resin than fdm?
@GeekDetourАй бұрын
Hi there. I feel the same about resin: I love the machines, I love the fantastic finishing - but I print practical things 95% of the time. The printing cycle on FDM is more convenient and clean. Just a few times I used Resin for my practical parts and if you really need precision you must account for the shrinking that will happen on the following days after you print them. So, it is time-consuming. 🤷♂️
@OldSkullSoldierАй бұрын
I print mostly practical things. Precision on resin is waaaay higher. You can very easily print things that will fit into each other with resin, while with FDM you usually need to under extrude. On the other hand if you FDM print with something better that PLA (e.g. ABS or PETG) you will get much better durability while maintaining stiffness. For Resin generally tougher resins are softer/more flexible, which is not good for many applications. What can you do is limited only with your imagination.
@ivandiv7946Ай бұрын
+ for comparing saturn’s
@matthewhaworth5935Ай бұрын
Most resin is sold in 1KG bottles not 1L! I know you know this but that is an important false equivalencey that the resin community needs to know - some resins 1KG may = 1L but it's not necessarily a constant! Funny how we just talked about this the other day in a comment though.
@FauxHammerАй бұрын
yeah fair point. but you know what I mean
@FaiytheАй бұрын
Sadly I'm not sure I can justify going up to the Saturn 4 Ultra and so was looking at this or the Mars 5 Ultra, thanks for the video, I think I will go with this one.
@FauxHammerАй бұрын
Good call it’s not a bad machine as I said. Not considering the Saturn 3 tho?
@FaiytheАй бұрын
@@FauxHammer I'm brand new to 3d printing, and the Saturn 4 seemed a lot more easy to set up and begin using straight away than the Saturn 3/Ultra, which is a big thing for me
@FauxHammerАй бұрын
@@Faiythe totally fair reason. Thanks. I like to see why people choose things
@redbusters1460Ай бұрын
just bought saturn 3 ultra for the same price as the base saturn 4. faster delivery because not on pre-order, same print quality, larger print size and wifi sold it to me.
@FauxHammerАй бұрын
Yep. I would easily take that deal!
@Ben-vg5rpАй бұрын
Just found your channel, love your videos 🙏🏼 Bought the anycubic m7 today as my first resin printer
@Don-nd2wmАй бұрын
Both videos would be nice, but anyway I already bought the s4 ultra 😁
@lanzer22Ай бұрын
Great video. When the Saturn 3 is pretty much the same printer there's no reason to pick the regular Saturn 4 IMO. Bed level had never been that big of an issue, the older one isn't much slower, and the old version can even print taller! Elegoo had been selling the refurbished Saturn 2 for $200 and that's the true value king. Though considering that a few bottles of resin would run you $100, there's very little reason to not get the Ultra instead.
@EyegazersphotoАй бұрын
What I would find really useful would be a detailed comparison on the slicer settings between the normal and the pro’s. Reviews mention that the lift speeds don’t come into the pros due to the tilting release vat, but it would be nice to see how much that really simplifies getting the resin settings dialled in for miniatures and dimensional accuracy
@FauxHammerАй бұрын
I showed this already in my 4 ultra review. Literally took some a screenshot of the settings gs and removed half of them that are no longer relevant.
@EyegazersphotoАй бұрын
@@FauxHammer Thanks, and I saw this. As a FDM person that is considering adding resin to the mix - it would be good to see how the missing settings would be used and what it would save me as a beginner. Probably a bit of a niche request!
@FauxHammerАй бұрын
@@Eyegazersphoto no worries. IO mean with resin there are far fewer settings than FDM anyway. But lift and retract speeds are some of the more complex and confusing ones. With the Ultra, they are all gone.
@bogatyr2473Ай бұрын
Absolutely love my Saturn 3. The 4 Ultra looks cool but I'm waiting to see a built in heater before I consider an upgrade.
@FauxHammerАй бұрын
They have an accessory heater…
@tadejpeckaj1151Ай бұрын
I just got Saturn 4 Ultra a couple of days ago… will try it out this week, just need to find some time :)
@EmanueleC_BRАй бұрын
I'd be quite keen on a skip generation comparison. Most people don't upgrade every generation, but instead look for the point where the feature benefits become justifiable. So for example, I have a Saturn 2. Saturn 3 wasn't likely to tempt me, but a 2 vs 4 comparison might. It might also highlight how far (or not?) things have come over that period.
@FauxHammerАй бұрын
Oh man, my list of videos to make keeps growing…
@GeekDetourАй бұрын
4:17 Geeeez! It's me! Thanks man! Have you tried adjusting the screws on yours too? Or you got even pressure from factory?
@FauxHammerАй бұрын
Hey man, yeah.. mine was fine as was. But seen enough people talking issues that I figured your video is the best place to send people
@dueckisАй бұрын
Love the green of my Saturn 4, but no anti aliasing is a deal breaker for me. How can a standard feature like that not be included on a printer in 2024?? Mine is sadly going back.
@FauxHammerАй бұрын
Antiailiasing works fine on mine…? Use the older version of chitubox if the setting isn’t there.
@dueckisАй бұрын
@@FauxHammer hmm, anti aliasing is not there for me on the newest chitubox. Be aware that only the ultra has that feature. I spoke with elegoo and some other people from the community. I can send you a screenshot of the email if you need one. It's very disappointing, no reviews mention it, there's nothing on the website. Only after buying you realize it.
@dueckisАй бұрын
@@FauxHammer It's not supported, not for the normal S4, only for the s4u. It's so annoying, it was mentioned not on their website nor in any review...
@dueckisАй бұрын
@@FauxHammer I've asked them about it and they told me it's not and will not be supported
@FauxHammerАй бұрын
@@dueckis I got it working though. I checked it. It does work
@Anne3000Ай бұрын
The green’s heaps better than the red, aesthetically.
@FauxHammerАй бұрын
Agreed
@peterclegg2609Ай бұрын
I'm surprised bambu haven't had a crack at resin printers yet.
@AyeohxАй бұрын
That'll be when I buy my own resin printer. These lazy resin printer manufacturers really need the competition.
@BigSooshiRollАй бұрын
ive wanted a saturn 4 vs saturn 3 video for so long now please do a comparison of all
@FauxHammerАй бұрын
I want to do it but I have a lot on and only about 3 people have requested this. Also the longer i wait, the more Saturn3's are selling out so it will be a video that has about a week's worth of life. Lets see what i can do
@BigSooshiRollАй бұрын
@@FauxHammer whatever you can do ill be happy with youve been my gateway into this hobby and i trust your opinions thank you for the response
@mitcho590Ай бұрын
I really really want to see a s3u vs s4u including print speed times doing the same prints. No one on KZfaq has done this and it's frustrating lol
@felixxcatusАй бұрын
it is a sleek printer but... I've never struggled with leveling a build plate so I don't see a drastic improvement over the saturn 3 right now it's 40 euros more for a flipping lid, a slippery build plate and 3cm less build height does look cooler
@FauxHammerАй бұрын
you summed up my review in 3 lines.
@OldSkullSoldierАй бұрын
with loss of build height Elegoo lost advantage over Anycubic M5S which has mostly same features as S4.
@FauxHammerАй бұрын
@@OldSkullSoldierexcept print quality.
@BlueBirdGTVАй бұрын
If the ultra had a green lid i probably would of already bought it 😂
@panoramer-rr2muАй бұрын
Maybe they could design a tray like magnetic plate that covers the lover part of the build plate and the sides high enough to cover the gap so no resin can get there. The springs would still be functional. Because of that build plate I deleted the Saturn 4 / 4 Ultra of my list. In the beginning it will be fun, but later a nightmare to clean that gap
@leroybrown9143Ай бұрын
I haven't had any problem with the gap. It's no worse than my 3 Ultra. The real headache is that there's no grip, so I usually handle it with two hands.
@pablofiasco2Ай бұрын
thinking on it, i wonder if theres a 3rd party market for Resin vats with intelligently designed spouts?
@calilifestyleАй бұрын
Thanks , for others and your self, i have noticed that the Ultra is highly rated . On fence Ultra or HeyGear Reflex printer? or both good , Both seemed nice at Rapid, but dang prices make a difference, but would rather go with quality.
@FauxHammerАй бұрын
HeyGears is easily the best printer on the market. But they lock you in to their resin
@AdrianGreen-qr4yyАй бұрын
good review. the build plate does put me off, not just the fact its a nightmare resin trap but the compression issue that crops up, to me, could be made worse with this. loot studios has some amazing models and ive had no print issues with the pre supported ones. a comparison vid with the 3 vs 4 would be good to see. keep up the great reviews and editing! MULTIPASS!
@FauxHammerАй бұрын
Yeah I’ve see a few people have that attitude about the plate.
@kurtwall6479Ай бұрын
I'd like to see a comparison between Mars 3 and Mars 4.
@FauxHammerАй бұрын
I will do that
@mvirtuos4 күн бұрын
What about 150mm/h printing speed ?
@tillerzeit24 күн бұрын
So i got one yesterday. Set it up test printed nicely tried another print of mine that failed found out why resliced it and shot for round two...then the touch screen died. Maybe I'm cursed maybe I got a lemon either way I found out i ordered it from the wrong elegoo amazon page and paid way too much for it.
@ingooooooooalАй бұрын
I am still working with my Photon Mono 2k ... it may be the time to think about an UPGRADE.
@MaddnessCreationsАй бұрын
Mono 4k here and thinking the same
@SOCMMOBАй бұрын
I got an S4U as my first resin printer. I don't see a point to the non-Ultra. Way fewer features for not much less money. Long term we'll see how the tilting vat works out, but I've been happy with its performance thus far. Now I just need to get less shitty at doing supports.
@FauxHammerАй бұрын
Agreed!!! And I still love your thumbnail
@SOCMMOBАй бұрын
@@FauxHammer haha thank you!
@alanpreston1822Ай бұрын
If you think the elegoo laser etch is tough to remove prints from, done get an Abycubic printer. Those etched plates rock.
@FauxHammerАй бұрын
It’s the same thing, different pattern
@OldSkullSoldierАй бұрын
It's a matter of good scraper. Just don't use there blunt metal ones, but buy some sharp plastic: cost is like 1$ per scraper so even if you need to replace one every 30-50 prints it's fine. And you do not damage the plate, which is good if you want to keet that pattern visible on front faces of some of your prints.
@7demo7reviewАй бұрын
You said that this is the same screen as the Saturn three, I just broke my screen on my Saturn ultra 4, can I use the screen for my ultra? They don’t seem to have the replacement parts on the website yet.
@CrAzYFearwolf2 күн бұрын
So should i get this or the 3 ultra because they are both at 299
@VictorBottinoАй бұрын
Hey Ross, in your opinion, which one do you think would be better: the Mars 5 Ultra or the Photon M7 Pro?
@FauxHammerАй бұрын
M7 Pro. that's a wild difference in printers though. makes the question a bit odd.
@StandardName562Ай бұрын
I just bought the Mars 3 Pro
@NoFearPrintАй бұрын
I got mine yesterday and have already failed 2 prints. Its been good.
@jukinhaumАй бұрын
Hi there! I loved your acid review, thanks for helping us to choose, but if is not asking to much could you make a review between saturn 4 ultra and photon m7 pro?
@FauxHammerАй бұрын
Already on it mate, it’s coming
@jukinhaumАй бұрын
Thanks! Here in Brazil the price is high, almost the triple, so we need to be sure before buy! And again thanks for the review, i love when people are genuine, and you are sir!
@dkev001Ай бұрын
Thank you for not using that ,oh so enjoyable, stock footage. Your videos seem much more streamlined.
@ciegos0oАй бұрын
Good review! Between this and the Anycubic Photon m7 pro, which one do you choose? If I already have a Photon mono x 4k, is it worth the change? Cheers
@FauxHammerАй бұрын
Between “this” and the M7… this Between the Saturn 5 Ultra and M7… I’m doing a video on that
@user-ib8ti3yq8sАй бұрын
Please compare Saturn 4 to Saturn 3 I really contemplating Saturn 3 Ultra vs Saturn 4. And i think 40$ more expensive 3U may be better value for me since wifi, also plus 40 mm on Z axis which is sweet.
@FauxHammerАй бұрын
Will do but to save time. The Saturn 4 ultra is so much more than the 3 ultra.
@Konradius001Ай бұрын
I have been using a whambam magnetic plate upgrade on my Phrozen Sonic Mini 8ks for almost a year now. It allows me to put the base layer exposure to essentially unlimited so I never have to worry about the base letting loose. And when a print is done, the original build plate stays in. I peel the whambam iron plate off the magnetic plate, and flex so the print is immediately off the plate. I can literally start a new print within 3 minutes. Most of that time is making sure with a scraper there's no cured resin left in the vat. Should I get a new printer (eventually, when this one fails beyond repair), I will certainly get that upgrade immediately regardless which printer it is. I love almost never having to handle the heavy buildplate itself. It stays in the printer except for cleaning when I switch to a different resin or something like that. Now I understand that when switching between a large amount of printers such an upgrade would not work for you. What are your thoughts about those plates? I'd recommend them to basically anyone who doesn't mind investing 30 minutes and maybe €50 or so to have a far better printing experience.
@philippjoswig6143Ай бұрын
Just bought the Mars 5 Ultra and im wondering now if the new features are necessary. Really unsure if I shouldve went with this printer as a first one.
@fluxcapacitorАй бұрын
The tilting vat of the Ultra erases half of the settings (Z distances and and speeds) in the slicer, which is excellent for beginners.
@Hero1117aАй бұрын
Please compare the 3 and 4, standard, ultra! Thanks
@FauxHammerАй бұрын
Ok. Will work on this asap
@christianortiz3738Ай бұрын
Gk3 ultra is my pick 😂
@JohnSmith-rt5yqАй бұрын
No AA on this printer.... that's a huge issue.... why is that not a deal breaker? The ultra has AA active.... this one doesn't. Ridiculous!!! Elegoo, wtf is that about? If you want to remove the vowels using AA, be warned only the ultra can use AA.
@dueckisАй бұрын
It really is ridiculous, no mention anywhere on their website. I wouldn't recommend this printer to anyone. Mine sadly needs to go back.
@runklestiltskin_240728 күн бұрын
This should be the top comment
@dueckis28 күн бұрын
@@runklestiltskin_2407 fr, at least pin this comment or something because how is anybody gonna know if nobody tells them. Of course it's not the fault of the reviewer, but still.
@cocofilms552427 күн бұрын
Sorry what is AA? I’m kinda new to resin printing.
@dueckis27 күн бұрын
@@cocofilms5524 AA stands for anti aliasing, just search for resin printer anti aliasing in Google 👍
@timstoth427128 күн бұрын
Interesting video BUT my beef is with your purchase links - its all well and good you get a percentage no issue with that BUT the prices are the same price on the internet so there's nothing in it for me..............!
@GameUpOGАй бұрын
I have my saturan 4 ultra but they still haven't shipped the heater.
@FauxHammerАй бұрын
I’m still waiting on my heater too…
@elidavid199320 күн бұрын
Would a saturn 3 be a better choice?
@FauxHammer19 күн бұрын
It could be if it’s a lot cheaper. They are mostly the same thing…
@Whoopsie00Ай бұрын
Man in NZ the choices are tough. Elegoo has a single distribution in NZ who overprices everything by like 50% and importing costs hundreds additional. Anycubic however store ships to NZ for $40, though I'd rather a Saturn but it just doesn't make any sense.
@Katazo98Ай бұрын
I just realized he said Saturn 5 at 1:41
@FauxHammerАй бұрын
Ooops. I’m so confused between mar5 and Saturn 4
@GeorgeSlade1Ай бұрын
Question! If the bed springs compress to make it flat level and then springs back when it lowers won’t that leave small gaps on the high side between print layers?
@FauxHammerАй бұрын
Yes
@GeorgeSlade1Ай бұрын
@@FauxHammer That doesnt sound great what do you do to compensate? or don't you?
@AustinD367Ай бұрын
I will never understand why manufacturers still don’t know where to place the usb port and power switch on a 3d printer
@FauxHammerАй бұрын
They know. The decision they make is based on manufacturing costs. The control board will be at the back. And 1 board is cheaper than 1 board with extension cables to the front
@Mr.NM267 күн бұрын
woah $319 there and it is $529 here in the Philippines lol
@christiangruening352Ай бұрын
I mean…there is the GK3 soon, eh?
@lordnovasАй бұрын
Could you turn off the Max fill detection?
@FauxHammerАй бұрын
Doesn’t seem so, no
@lordnovasАй бұрын
@@FauxHammer cool. I always fill past max for 15mm terrain. I hope they make it a toggle in the future.
@tomaszkarwik6357Ай бұрын
Ahhhh, bad ux on 3d printers, us fdm guys had to deal with that since forever. And then bambu came. My dad said this about my p1s "this thing is vey good, as i can just click print on the app, without any knowledge, and you (me) can change any setting you want" Pedantic comment that does not add anything here 2:28 it buggs me that you call it an "external power transformer", because the label " dc" suggests that the brick is indeed a full power supply, and not just a transformer
@WiNNiep00hАй бұрын
i bought the Saturn 3 Ultra last december...and i didnt unpack it yet...i had no time at all :/ made me sad to see that there is already a new version and i didnt unpack mine yet
@FauxHammerАй бұрын
Yeah sorry mate, it’s about this time every year they make a new one. Sat 3 ultra is still awesome though
@bradandteinacook3506Ай бұрын
Saturn Ultra vs M7 pro would be good.
@FauxHammerАй бұрын
Already on that, that's the surprise.
@bradandteinacook3506Ай бұрын
@@FauxHammer looking forward to it.
@andymeenanvideosАй бұрын
No spout & extra cleaning with the new build plate means I cant buy either this printer or the Ultra even though I want to, these are not trivial points (if you think they are you don't do a lot of resin printing)…why are Elegoo not watching Fauxhammer reviews and just using them as research & development tools, I mean he's telling you you're good and more importantly bad points you need to improve upon. Just put a decent spout on & cover up that silly awkward space above the build plate...( PLEASE ) 🙏
@malmfjordАй бұрын
I got a mars 3 ultra now what the NeXT step up printer i shod upgrade to?
@FauxHammerАй бұрын
Saturn 4 uktra
@malmfjordАй бұрын
@@FauxHammer is there big difrence on saturn 4 and 4 ultra?
@FauxHammerАй бұрын
@@malmfjordnot in Terms of quality. But features and speed. Quite a bit
@BlueBirdGTVАй бұрын
Do you have a comparison of the Elegoos and the Acubic Ms5 pro? Im looking to buy and rn its a race between Acubic Ms5 pro, Elegoo Saturn4 ans Elegoo Mars5U.
@BlueBirdGTVАй бұрын
But like you said these do win out against the Mars' with a sweet spot in size. I guess i was just torn by a tilt tray. If the Ms5 pro had a swingy lid I'd probably be sold
@FauxHammerАй бұрын
Not yet, but don’t get an M5, they just aren’t as good and Elegoo has a better heater coming.
@BlueBirdGTVАй бұрын
@@FauxHammer heater coming soon 👀👀
@user-ni9qi3ve1bАй бұрын
Hi really need help im bubble dizzy looking at all the printers, so basically im going to start jewelry casting and cant decide between saturn ultra 4, g2k, phozen sonic 14k, or any cubic 14k what do you think would be the best one, i know every one will say different but i like your knowledge and understanding of the machines and how you review them any help would be great thanks
@FauxHammerАй бұрын
WEll. i;m assuming you haven;t seen my phrozen review if that;s even in your list of consideratins still,. If you need a consistent printer and don;t wnat to worry about temperature, get the GKTWOI it's currently £649! see the code and click the link on my latest community post The Anycubic is a much better printer than they have done before, but it;s faffy witha weird heating system that will need cleaning. I love the Saturn 4 aswell, if you need speed and quality, that;s the one. though with castable resins thyiou may be limited on speed by the resion itslef being a bit more stretchy
@user-ni9qi3ve1bАй бұрын
Thank you for your reply much help thanks@FauxHammer
@sammkablaamАй бұрын
I’m guessing the big question will be whether to buy the Saturn 4 Ultra or wait for GK3.
@robertderry3765Ай бұрын
@@user-ni9qi3ve1bCastable resins. You 100% need a printer with a heater for temperature consistency.
@exjumper999Ай бұрын
May need to add an edit, at 1:40 you said Saturn 5 Ultra when you meant Saturn 4 Ultra. Also here's a free engaging comment to help boost the video lol.
@brennonwilliams9181Ай бұрын
I bought the saturn 4 ultra about 3 days before your last review (soz, I would have used your affiliate link otherwise). I completely agree that only a moron designed that build plate handle.... like seriously WTF? Also. Without that drip tray, i would have destroyed my screen on the first print, but why did they have to emboss it???? A bitch to clean. Still, amazing printer and Ross your reviews on both i think are best on YT for honesty about the pros and cons. Certainly I would stick with the Ultra. Thanks for another great review!
@luisamador1291Ай бұрын
saturn 4's vs saturn 3's LFG
@benburmeister3428Ай бұрын
Am I the only one using the spare USB port inside to run an electronic load tester to heat the chamber?
@FauxHammerАй бұрын
What spare usb port?
@benburmeister3428Ай бұрын
@@FauxHammer not really a spare i guess but I use the 2nd USB port inside the machine intended for the scrubbers
@FauxHammerАй бұрын
@@benburmeister3428 inside... where though?
@theromeogАй бұрын
In before he makes the video - "Resin printer Pour spouts are irrelevant - because they are all crap"
@DavidSmith-te9ggАй бұрын
Can't see me buying any new Elegoo due to the super-messy buildplates.
@A-scketchy-otter-lolАй бұрын
Hype
@CavemanGamingАй бұрын
Why in today's world do you need to use a USB thumb drive? Why can't I just plug it into my computer and send the file directly over? Hooked up once and forget about it. This is something I just don't understand.
@Bobby11Ай бұрын
Because they need ro keep "features" out to make the more expensive version look better
@kipkulich604221 сағат бұрын
This printer is absolute hot garbage for the record - and anyone considering this thing should SERIOUSLY reconsider. These "Auto-leveling" plates do NOT come leveled - and the instructions provided to level these things flat out can NOT get it in level no matter what you do. Two separate build plates and the same problem with both. Don't pay to beta test this rubbish.
@nh0jay305Ай бұрын
I got the max lol
@Reel_randomtvmanАй бұрын
Are you really Ross?
@FauxHammerАй бұрын
I think so. but who are we all... really.. do any of us exist?
@vladtheinhaler93Ай бұрын
I'm told, anything over 9", is a waste..
@FauxHammerАй бұрын
I heard 5"
@4Tugboats3 күн бұрын
I have ordered THREE OF THESE NIGHTMARES, and NONE OF THEM WORK !!! The first one had a fractured screen right out of the box. The second one would not even turn on. Now, The TURD, errrrr, I mean the Third one won't recognize any USB cards that I have used in my Elegoo Saturn 3 Ultra. DON'T BUY THESE BOAT ANCHORS !!! THEY ARE PURE GARBAGE 🗑!!!!!!!
@ReadyMack-gАй бұрын
Yay SATUIRN ULTRA 3 3 3 for the WIN RUMP 2024
@krunchy3761Ай бұрын
YOU should never use the word "A'ght." Otherwise good video.
@jasoncombs3232Ай бұрын
Why not? Slang proves popular with the kids.
@FauxHammerАй бұрын
Why not?
@krunchy3761Ай бұрын
@@FauxHammer You are a middle aged white Brit using what is primarily black American slang. It can easily come off as "mocking."
@krunchy3761Ай бұрын
@@FauxHammer You are a white middle aged Brit using African American vernacular. Comes off really cringey, even back in the 2000'a. In mixed company it may not be appreciated.
@GeekDetourАй бұрын
Now I’m curious about it… time stamp?! Ross can say anything. He is funny!