This was perfect, just what I needed to diagnose and repair my washer.
@Greenwitch_Garden9 ай бұрын
Omg thank you thank you!! I had a lid lock error and running through these at random somehow worked to clear it! F5 E1 error on the Maytag Bravos XL was solved! 😅 Edited to add: I realized after having this error multiple times all I had to do was leave the washer unplugged for 1 hour or overnight and it would reset. What a pain in the ass that was to learn after taking this whole thing apart to clean several components!
@lindabennison4167Ай бұрын
Mine was f5 E 2 same .problem .not fix yet
@MikeGreen-eb5ko3 ай бұрын
Thanks for the help! Great video!
@chris76-01Ай бұрын
Where can I get that service manual?
@ernestbrown2521Ай бұрын
Thank you for this video, God bless !!!
@devilmangamez86156 ай бұрын
What was the issue with this washer? Mine has the same problem. Diagnostic 19 sounds awful, just like this one. I have replaced the agitator plate. It worked for about 5 to 10 loads and its doing it again. Its obviously something with the agitator. Since I have replaced the plate, with no luck, should I now replace the gearbox to get new splines?
@jamieblair183013 күн бұрын
You are awesome ty for that worked perfectly.
@craigryder3712Ай бұрын
i have a F7,E9 error code says to possibly replace motor it doesn’t have a motor it has the rotor system unless that’s supposed to be the motor
@BoatFails4 ай бұрын
Is it possible another problem? I did this and everything was clear… could the pump be out? Thanks!
@Webrider35711 күн бұрын
mine has a deep fill button below the 3 you press to put it into diag mode, and it won't go into diag mode using the 3 buttons you used.
@andrestinoco892222 күн бұрын
I have a problem with minw. Saying drn
@analuciasalmon834711 ай бұрын
Si el Problema de la lavadora es el 000 o sea el seguro de la tapa…. Como lo soluciono? Graciass espero subrespuesta
@Asif_UltimateАй бұрын
thanks❤❤❤
@Weluvthat5 ай бұрын
My washer cuts on makes a sound and doesn’t perform no water just spins can anyone help
@ashleyhopkins13896 ай бұрын
Need help my maytag lx is just reading F5 nothing else and onto stop dingling like I don't know we tried the to reset by pressing all thoes buttons the way you did but nothing
@melanatedrichconvo79273 ай бұрын
Did you try unplugging it for a couple of hours or overnight
@lindabennison4167Ай бұрын
Sound like the bearings
@skywriter007 Жыл бұрын
Its actually MVWB MODEL. SEEN AT 4.36 ON ID LABEL. NOT MWVB.
@84twarner2 ай бұрын
How to reset F8E1
@tommy78mkd Жыл бұрын
Thank you for the help ordered a new interface panel and sealed the exposed portion of the circuit board with a clear coat. Good fix, may i ask what manual is that you are using and where i may be able to pick one up. I searched briefly and was only able to fine this one (Whirlpool Service Technician's Manual W10468340B)
@johncoyne4263 Жыл бұрын
I saw another video which showed this manual inside the machine. remove the top and look inside to the left of the drum. Good luck
@seanbakkila9217 Жыл бұрын
What sealant did you use and where did you get it?
@amandaokeefe6987 Жыл бұрын
If it's the lidlock switch and it keeps clicking you can not get into diagnostics mode. Just a heads up
@tommy78mkd Жыл бұрын
3M EDGE SEALER 3950 I have had it in my tool box from some previous job i have completed. But alot of coments say you can use CLEAR NAIL POLISH seem to work and i am sure probably alot cheaper.
@lindabennison4167Ай бұрын
Yes in side .pull the top off
@Planet-Asia8 ай бұрын
So at the end what you do ?
@Planet-Asia8 ай бұрын
Bc I was following your steps did everything but did you turn it off at the end or waiting some min .
@jt96024 ай бұрын
Would be nice if you talked
@lewisgoodleaf19797 ай бұрын
THE BODHI 12345
@johnsadventures67838 күн бұрын
Would be a better video if you told what you were doing. Fail