Get our exclusive tub rebuild kit on our website! 😎 lorainfurniture.com/shop/appliance-parts/maytag-dependable-care-washing-machine-tub-seal-bearing-rebuid-kit/

I watched your baring replacement on the front load neptune..Neptune... I gotta say that I watch a lot of vedios here on KZfaq and you have got to be the BEST person I've watch that clearly showed step by step instructions on how to do something. Thank you for that. Your instructions got the job done.

To the author of this video thank you very much it helped me fix my washer machine and I would like to leave a awesome review👍🏽

Great video boss!! All the details necessary to get the job done without any annoyingly unnecessary commentary you find with other videos. Helped me a great deal! I thank you sir!

Eugene thank you for the detailed video. I have 25 yo Maytags just like that that have performed flawlessly all these years and are getting to the point of needing some tlc. I appreciate you posting these. Take care

You're Awesome!! Greatly Appreciate your CLEAR & PRECISE Instructions with your "Insider" repair tips to eliminate First Timer Headaches!! Thank you👍👍👍👍👍👍

Great vidio Eugene. Every time you break a machine down. It's like brand new when it's complete. Your the best Eugene!!!

As an old Maytag repairman it great to see an older machine be repaired. I gotta replace the seal on my LAT9706 myself. Thanks for the refresh.

You're the man Eugene. Love watching you do a tear down / rebuild.

Good day Eugene , i have been watching some of your videos the last few days, you are giving people so much good advice. Even you make yourself unpopular to tell the truth. Thank you for your honesty and advice. Keep it up Sir. God bless you. Regards Jan De Villiers

I recently had a leak in my older Maytag washer. I found this video and did exactly what this gentleman did, including having to cut off the spanner nut with a small grinder because it was so frozen on. I ordered a tub seal from Amazon at half the price Maytag and other distributors wanted for it. I did not replace the sleeve bearing, probably a mistake but it seemed fine. I followed all directions, put the washer back together and it now works good as new. Thanks man!

Very nicely explained. Each step is too the point. Thanks

Great video as always Eugene. That thing should run another 20 years!

ace hardware has turbine oil! Sold in a zoom spout. Probably made for motors

Thanks for this video mate. Insanely helpful. I made a spanner for the tub seal nut but it would not budge an inch! Had to cut it with the dremel - same with the bearing. Thanks again, would have been a struggle without this video. All the best.

I would tighten the center nut first before the 3 tub bolts. To make sure it is down all the way. Also I would replace the spring clamps with all stainless hose clamps to keep the rust to a minimum. I used silicon grease to lube the rubber parts for easy assembly and a little on the bearing. It won't affect rubber parts and is totally water and heat resistant. My cork gasket had a gap so I had to carefully remove it and reglue it with shoe glue or contact cement.Thanks for a wonderful video.

Perfect instruction, fixed my leak right up.

Does definitely save me time and money! I appreciate the work you put in to share this information.

They sure don't build them like that anymore. The quality of your restorations is amazing.

Enjoyed the video as always...Eugene. That model was when Maytag was still manufactured by Maytag... Those were solid built machines and lasted a long time... Steel outer tub was better than plastic.... Oh nice upper arms too... Ha Ha...

need to patch the holes in my outer tub 22001114 since there are none available anymore. sure wish I had access to a new outer tub. Firing up the welder in 5 4 3 2 1...

Great to watch. When I did mine, I also lightly lubed the inside of the sleeve bearing above the transmission. Likely won't seize as that one did.

Nice video! Helps keep people from getting hardly efficient washers

I hate when those spanner nuts freeze up. It’s not uncommon at all. Nice to know how to get those loose. I usually make a mark on the tub to make sure that Allen screw on the mounting stem doesn’t fall into one of the recess groves when reinstalling it. It is hard work but worth it in the long run. Thanks for posting!

Eugene! You gotta review a Miele washer one of these days! PLEASE! 🙃

This is a all around excellent job! Great explanations and filming. I followed this to repair the same model machine. A few tips I would add. Use a torch to heat around the torx set scew. If it strips out, I don't know how you would get it out! Take care that you place the inner tub concentric with the outer tub. Mine wasn't and created a noise during spin cycle as the inner tub rubbed on the plastic tub cover. Fortunately, i was able to loosen the tub nut and readjust.

You only need to loosen the 1/4 inch agitator screw only a little bit and then pull it off

Need some more light on the subject....going to do this next week! Thanks

i came across your channel recently and this is the first video i'm watching with you in it. is it just me or do you look like the dad from pixar's inside out??

Excellent! Thank you.

Thank you, you made my day

Great information 👍

you had me at 1/4 inch nut driver

Awesome work, Eugene. I've always used laundry soap on seals that are going to have water touching them. I don't think a light film of oil is going to hurt anything or show up in laundry. Just a me thing. Plus, I've done most of these in laundry rooms. So soap or fabric softener was the closest lubricant. Do you just use electric motor oil?

Love these videos :) Can we get a full wash video of it?

I wish I had this washer! and also have you done any full wash videos on this washer?

Very hot. I couldn’t concentrate on the washer

Would like to order that parts package.Could you send me the info ..Great well done 👍

Second time I watched this video... Still a fantastic video.. Those older Maytag's were the best ever... Plus like another fan said, you look HOT in your wife-beater shirt... It's the arms!!! But again love a great restored top load center washer.. they are the best...

Can you tell me what the white plastic half ring is that's just above the sleeve/threads in your video? Is that supposed to look like that? Thanks. GB

IIRC one of the tub bolts is shorter and is supposed to go on the front support.

Cool!

Hi Eugene! I got a 97 Dependable Care, is it worth doing one of these kits before it fails?

The small Allen set screw for the tub stem won't turn. Any suggestion/s? Thanks.

As Always Eugene very nice video. How about a Amana Washer main bearing assembly replacement the ones that mirror the Speed Queen top load washers.

Hi Eugene, will this procedure be the same for the older models as well? I have a 1979 A608 that has a bad tub seal. Are the parts the same?

Would this work for a LAT9206BAE model?

where can I get that spanner tool? Home depot no have

Wish someone would show how to defeat the pesky door switch.

Is this washer the one you did the 3 hour ASMR video on?

This is definitely above my skill level.

Just unscrew the agitator screw a little bit

Can't get over about how hot this guy is...

My "tub cover" seems to be leaking after repairing all the seals in the tub. Any ideas how to fix this issue?

hehe 6:18

$199.95 for that kit to me that's pretty expensive. But it's still worth it.

Very handsome mate

He looks like Luigi

To Much I'll tell my wife Different. Use her credit card buy a new washer with warranty

Cannot see, video too dark

He's hot

Sure....You lost the footage 😁