Your video is the only one that showed how to test the drain and spin. Thank you.
@Shareefhamida2 жыл бұрын
U are the savior of bravo xl mct owners with guests over who need to use ur washer
@reginakenger57372 ай бұрын
Thank you for the very informative video. I have been struggling with the ul (unbalance mode) for quite a while. And I don’t have the means to purchase a new washer. Or even hire a repair person. You’ve saved me.
@wetfart1387able Жыл бұрын
Trying it now. Fingers crossed (2:53pm, Saturday July 29) UPDATE 2:54pm, same day): IT WORKED!!! THANK YOU!!! Fair warning: based on other videos, it’ll probably have to be tightened again, but this worked for the time being.
@SQRLFury Жыл бұрын
Thank you so so much for posting this!! I can get my sheets in the dryer tonight because of it!! 🙏🙏🙏
@GrandmaSezSo Жыл бұрын
Thanks. I have the same short-lived machine doing the same thing, throwing UL error everytime toward end of cycle. I can't afford a repairman or new machine. I really appreciate your video.
@CC-en7kq3 жыл бұрын
I tested a load of clothes and I'm one happy camper😃😃 it works 👏👏👏thank you so much!!
@6static2 жыл бұрын
The least you can do is unplug the washer for a minute or so, it is run by a computer and rebooting it may correct everything, this is what I did and it works in my case, hope it helps....
@JillinOhio2 жыл бұрын
Did not work but this has helped while I save for a repair
@williamqualls45782 жыл бұрын
Obviously this video is for after you've unplugged it and plugged back in
@ARamseyGuy Жыл бұрын
These washers typically have a small battery to retain cycle settings in the event of power loss. Unplugging the unit does not typically reset the computer.
@aprilrodriguez5874 Жыл бұрын
Wow thank you so much for this video!! I was almost going to cry because I thought I was going to need a new washer and I can not afford it at the moment. Thank you I did this and it worked !!! You are a life saver!! 😅😅😊
@CC-en7kq3 жыл бұрын
Woke up this morning, I have the same washer that said ( UL ) it was a small load. I did everything you did and it drained, thank you so much for this video. Now I need to test it, to see if the problem was taken care of.
@BillSr.2 жыл бұрын
Did it fix your problem? Or was it something bad like bearings?
@CC-en7kq2 жыл бұрын
@@BillSr. It fixed the problem 😃 I was glad to have seen your video. Thank you.
@hoodhunter326210 ай бұрын
thank goodness I found this video. It help me found a way to spin dry our clothes. Our Maytag Bravo XL consistently failed with 14 minutes before completion (I believe right before the spinning occur, and the code is uL). I find this code to be generic and I'm still unable to pinpoint the root cause. I had a repairman came out and replaced an official Maytag suspension rod and that didn't help.
@falk006910 ай бұрын
Probably the bearings then. This washer definitely has its share problems.
@marie1811922 жыл бұрын
Thanks you sooo much.. I have an older version ( was given to me)and I tried to opened it to see if it was the springs etc. Couldn't get it to open because of rusted bolts... but this helped a lot so I didn't have to have clothes in the drier for multiple times lol... thank you
@lindabennison955 Жыл бұрын
The ones with the glass .has any take the glass off .then you can put close in when you want and extra water
@AlyssaTheWasherLover12192 жыл бұрын
5:09 The Washing Machine Having A Heart Attack 5:11 And Then Has Seizure
@gr8notes Жыл бұрын
You rock!🎉 Just fixed my UL of pillows. Worked like a charm. Thank you.
@vickytorgerson33112 жыл бұрын
Lifesaver until my new washer comes thanks so much!!!
@meganusmilebusiness57103 жыл бұрын
OMG!! YOU TOTALLY SAVED MY FRIENDS SANITY! YOU ARE AWESOME THANKYOU. 😊
@danielchenevert771318 күн бұрын
Your video was very helpful. The only one on KZfaq to address my issue for the same type of washer. If you replaced the suspension (also did that), and the bearings including replacement spindle (possibly my next step), did you ever managed to find out what the issue with your washer was? Or are continuing to manually play with the spin cycle every time? Thank you.
@user-tl6pv7sy2q9 ай бұрын
Thank you soooo much! This was so very helpful! I have the same washer and same problems
@jimmyjimjim30543 жыл бұрын
I've had one for 8 years now and its been great. I think the Bearings are going out though.
@UniqeStyleDesigns2 жыл бұрын
2:55 thank you again 🙏
@ItalianStallion14153 жыл бұрын
In order to drain and spin only, you should try this... Select "rinse/drain & spin", then DESELECT "extra rinse", than start the cycle. It should not add water when you do this.
@lindabennison955 Жыл бұрын
It works
@Luckiekatie Жыл бұрын
Just saved us from the horrible laundry mat!!!! Ty ty ty
@davidcampos55068 күн бұрын
Ready fixed my washers thank
@virginiamoore60642 жыл бұрын
Thank you and I appreciate you posting this it had totally helped me sooooo much thank you GOD BLESS YOU
@joses.garcia21248 ай бұрын
I had this problem with mine and the way Got my washer to stop working. Is level my washer by fixing the problem with the hobble Legs on bottom. The only way I got it to stay level was taking the legs out and adding a locking nut to the leg and when putting the legs back in is level the washer with the level going across the top of tub not lid once level i used lock nut to tighten against the washer frame. also laid sum rubber matts on bottom of legs to help the shaking on floor. The legs on washer are the worst thing about the washer.
@ginareichenbach17145 ай бұрын
It actually worked!! Thank you so much!
@mymunoz33 жыл бұрын
You are the *BEST EVER* Thank You 🙏🏻
@robinowens63 жыл бұрын
Thank you for this video! It completely solved my problem!!
@RaStro-sl4fg2 ай бұрын
Am getting an OL code what is the that for ? but same thing it leaves the clothes wet, so go into diagnostics and do the spin and drain like you showed, but new loads keeps stopping at OL. Any susggestions
@noble24123 жыл бұрын
OMG... THANKS 😊 🙏 I really needed this video
@UniqeStyleDesigns2 жыл бұрын
Thank you sir 🙏🏽
@victorialopez49752 жыл бұрын
Muchas gracias güero, si me sirvió
@UniqeStyleDesigns2 жыл бұрын
Dios bendiga norte America 🇺🇸
@davidcampos55068 күн бұрын
You the best bro
@tonyschol4326 Жыл бұрын
Where did you find the new bearings kit? I replaced my stabilizer rods with still the ul code. So next I’m going to do the bearings. Mine is a MVWB980BW0 tho
@falk0069 Жыл бұрын
I just pick one from Amazon that wasn't too expensive but still looked quality.
@kalamelliel2 жыл бұрын
Great video I have the same problem where the tub spins violently just like in the video I did replace the suspension rods but continue to have the same problem what do you think I should do?
@falk00692 жыл бұрын
You may want to double check the rods you got and make sure they were actually better. I made that mistake and purchased bad ones on Amazon. Check out this other video: kzfaq.info/get/bejne/hrdnapiU3bKYlZ8.html
@ulicom222 жыл бұрын
2:55 you save my ass 😩🙏 thank you!
@SuzanneC-ht1er4 ай бұрын
We have BRAVOS XL that keeps having UL code show on spin cycle and still shows after trying to rebalance clothing. We have never had any work done purchased new about 8-10 yrs ago. My husband is NOT handy is ready to purchase new washer. Any suggestions I can try? What is usually cost to have technician come over to fix unit?
@falk00693 ай бұрын
Did you end up buying a new one? It probably is worth it because they things have so many issues and if you made it 10 years--not bad.
@zaccheuslittlejohn5603 Жыл бұрын
Awesome Job Thank You 👍🏿🙏🏿
@goo22868 ай бұрын
Thanks so much! You saved my headache! I have same washer like yours.
@mathewmouritsen9347 Жыл бұрын
Hello thank you for this. We can use our washer in a pinch now, but I still need to fix it for good. When going into maintenance mode in the video, it flashes"H94" and you mention it goes through error codes. Mine has the exact same code. Do you know what this is? I am thinking of replacing the bearing but want to make sure it is not an electronic problem (motherboard) that will make it worth just throwing the machine away.
@paulafiumidinisi24402 жыл бұрын
Thank you for this amazing video, I use it every time.
@nhangeta2 жыл бұрын
amazing video, thanks for sharing
@jacobjche2 жыл бұрын
If u want to get rid of ul, make sure it's perfectly level. Then springs. (Check tub and make sure it's not wobbling in it's hole) Then stator. Then control board. Then new machine. In that order.
@falk00692 жыл бұрын
That makes complete sense. Just make sure you don't do what I did and order crappy springs. That is where my downward spiral began.
@evelynspencer6031 Жыл бұрын
I was getting an LD error code on my washer. I took out the drum, removed a hand towel from the tub and cleaned out all the hoses, checked the pumps for obstructions, and while at it, replaced the bearings and shaft since they were rusty. I'm still getting an LD error and when running diagnostics, I got an F32 error. Do you have any idea what may be going on? The washer is not draining and making a gurgling sound.
@maryward6132 жыл бұрын
May I ask how much it costs to get the rods replaced by a repairman? Just a guess, and I'm in Texas. I hated my machine before the OL code. I can't wash blankets in it and no control within the cycle. I know now with your video, but the old fashion dial where you could click it to any part within the cycle was much better.
@luclapierre17252 ай бұрын
would someone could help me please, mine dont work on cold cycle mode its always use hot water
@eienanh838710 ай бұрын
My has dL problem, can you help? What’s the problem you know? I turned on press wash, after water spray for 5 sec then DL error went on.
@falk006910 ай бұрын
As far as I know, the DL means it wobbles too much. It is very strange to me you'd see it so soon and before it even needs to spin fast. I really have no idea. Good luck.
@ForbiddenFruit96 Жыл бұрын
I got the exact machine and its beeping and going crazy. Cant get it to work. Everytime i try to start, it resets and beep beep. We unplug it for a while and same problem
@Crickmers8 ай бұрын
very helpful, thank you
@HandyTim3 жыл бұрын
That's pretty cool great video
@minniered4115 Жыл бұрын
I want my tool belt in purple!!! I did it!!!
@humbertogarcia97495 ай бұрын
Helps me a lot
@cherylcunningham80212 жыл бұрын
I did this on my Bravos XL MVWB980BG and it worked. My question for you though does this "fix" the problem or do you have to do this every time? By reading the comments here it seems that this is a big problem on this machine. I'm trying to decide whether to ditch it for a new one or not.
@falk00692 жыл бұрын
I've had to do it once in the past year after doing the various hardware fixes mentioned in my other videos. It is a good back pocket fix to drain it when it happens "occasionally". If it is happening every time you probably have the bearing going bad or the suspension rods.
@JohnnyDevinTV2 жыл бұрын
I tried this & got it to work on the first try. I had it spinning on low & all was well. I stopped it to check how dry the clothes got & I realized I needed them to dry more... so I tried it again & I got the F51 code... & now that’s what I get every time. Help. Lol
@falk00692 жыл бұрын
F51 means it is having troubles draining. You might have trip that error code and now it is show up in the history when you put it in maintenance mode. I thought it just flashed all the past error codes and then it went to 000. But maybe you have to push the button one more time. Let us know if you figure it out.
@falk00692 жыл бұрын
I read my manual and it says it will store up to 4 fault codes. Just continue to press the same button to roll through them. And then once more to get to the 000. You should then be in manual maintenance mode.
@JohnnyDevinTV2 жыл бұрын
@@falk0069 I kept trying & got it to spin again with the F51 disrupting. Thanks.
@MeLiiSiiTa03 Жыл бұрын
I Just tried this on my Maytag Bravos MCT and it doesn’t work it just gives me codes with the letter C Everytime I press the buttons 😢
@kendrickkeeley Жыл бұрын
Hey does anyone know how to do a quick calibration on this washer? Sometimes it workes fine ... our days im plugging & unplugging
@skipbrott97143 жыл бұрын
So what's the resolution when every load I run kicks out a uL code with 14 minutes remaining on the wash cycle? I don't think it's a diagnostic issue at that point.
@gbar20933 жыл бұрын
I have the same problem with the uL code on with 14 minutes remaining
@skipbrott97143 жыл бұрын
@@gbar2093 I replaced a couple of parts and I thought I had it working but I'm still getting the problem with some loads (not all). I did find the repair sheet that was with the unit and am able to run the last part of the cycle manually to get it to finish. But that's not really the best long term solution. I'm probably going to just replace it at this point rather than spend any more money.
@gbar20933 жыл бұрын
@Skipp Brott yeah I'm going to try and fix it if not I will have to just replace with another brand. Not sure what to go with
@KR-db782 жыл бұрын
Its a motherboard issue. If the motherboard tells the washer to stop it will. The good and bad of Technology....
@jenniferreece35412 жыл бұрын
Mine is throwing a c6 code pump is clogged and I have no darn idea on what to do
@jstar2212 Жыл бұрын
My washer is throwing the UL code and nothing has worked. After being gone for a week I did a load and the washer is working fine. I ordered the suspension rods and am still waiting on them to be delivered. My question is if the washer is washing fine after not using for a week is the problem the rods or really in the board?
@falk0069plus Жыл бұрын
it could many things. I ended up changing a sensor, bearings (twice) and the rods. Check out my other video on how to check your new rods are actually good. I fell in the trap of installing bad ones and ended up replacing the bearing a second time when I didn't actually need to, plus the sensor which I didn't need to. kzfaq.info/get/bejne/hrdnapiU3bKYlZ8.html
@jstar2212 Жыл бұрын
@@falk0069plus ok thanks for replying. I did order original OEM suspension rods. I was just trying to save money if it might be something else.
@tiffanylamb7852 жыл бұрын
So Mine shows the Ld code on it. I've the drain pump and it still will not drain. Even when doing this that you explained in the video. What else could it be?
@falk00692 жыл бұрын
I think that code means your drain is clogged. Check out this video: kzfaq.info/get/bejne/ed6jdqWesbCnYZ8.html
@Nebdog111 Жыл бұрын
My machine is making a loud noises when spinning and then going to uL. I think I need a bearing replacement?
@falk0069 Жыл бұрын
Yeah, I bet you are right. Watch some KZfaq videos and see if it is something you want to tackle. It isn't too bad.
@appliancealliance44443 жыл бұрын
Fyi if you replaced the suspension rods and the UL code still appears with the tub shaking, did you use OEM parts??? Suspension rods that are not genuine to whirlpool/ Maytag may still give you issues because they may not be built to the original factory standards. Try putting in new OEM suspension rods.
@falk00692 жыл бұрын
You are completely right. There are definitely bad rods and in my case it made thing worse. I made a separate video talking about this.
@reneeshepherd9723 жыл бұрын
Well what I mean is there are no clothes in it at all and about 4 inches of water, when I tried to do the trick to turn on the pump to drain it, it just makes that humming noise and doesn’t empty. My daughter was washing clothes and I guess it was trying to drain and then just started to and then made this loud humming noise that wouldn’t stop until we unplugged it. We’ve tried to call people locally to help but can’t find anyone. I have tried to remove the agitator plate thinking maybe it’s stopped up but I can’t get the nut to come off.
@falk0069plus3 жыл бұрын
sorry I missed your comment. Did you have luck figuring it out? It sounds like the pump went bad to me, but this is outside my experiences.
@reneeshepherd9723 жыл бұрын
@@falk0069plus thats ok, we ended up just getting a new used one
@Broham703 жыл бұрын
Good video thanks but do you have to do this every time you wash?
@falk0069plus3 жыл бұрын
No. Once I found the issue with the new suspension rods I got, it no longer happened. Actually it did once due an actual unbalanced load. And instead of rebalancing and running it again, I jus did this drain trick. Check out the last video in the play list I created to know what I mean rods: kzfaq.info/get/bejne/prxkmqV4zaizdZs.html
@marcelle.2xx2 жыл бұрын
Was there a time for that to happen so I don’t know how to get to my
@LovingArmywife9 Жыл бұрын
Thank you so much! Question where can u find the bearing? Lol
@falk0069 Жыл бұрын
I just ordered a highly rated one on Amazon that match my washer. Spent about $40 on the shaft and bearing replacement kit.
@MrHanowski8 ай бұрын
You could have a bad suspension which are easy to replace.
@falk00697 ай бұрын
yep..that definitely was also one of my issues. I have a separate video that explicitly shows how to tell if they are bad.
@wilmaruby90652 жыл бұрын
My washer is same model also doesnt spin at 12 . In manual mode the no spin light is on and I cant lock the lid. Any suggestions?
@falk00692 жыл бұрын
Is it the exact same? Mine is MVWB725BW0. And you have a 'Water Save' button that doesn't lock it? All I can think of is it could be slightly different. Can you find your service manual? If you can lift your washer up, it should be taped on the back of the front pane. That is where mine was.
@olegs5433 жыл бұрын
Thanks I think I fixed.
@reneeshepherd9723 жыл бұрын
What happens if the water doesn’t come out!
@falk00693 жыл бұрын
I'm not sure. Sometime very little comes out if the clothes isn't that wet, but that was the only reason I would do it. I was able to finally fix my problem, so I have not had to do this now for some time. I got a few other videos linked to this one in a play list if you wanted to see some of my other things I tried. My issue ended up being bad bearers and bad suspension springs (that I purchased first to try fixing my issue).
@GrandmaSezSo Жыл бұрын
You probably have a new machine by now but I'm stuck with the Bravo XL. Your spin fix works but I have to do this ever single time. IS there anything in your pamphlet that instructs how to reset it? If you still have that instruction sheet, can you photocopy and email me it?
@falk0069 Жыл бұрын
I think I still have it. I'll have dig around for it. Do you want to email me first? It is just my handle @gmail.com.
@GrandmaSezSo Жыл бұрын
@@falk0069 Thank you. I sent you an email
@falk0069 Жыл бұрын
@@GrandmaSezSo hopefully you got my email with the scan. Hope you have luck.
@Zachamation Жыл бұрын
@@falk0069I emailed you as well if you would be kind enough to respond, thank you 🙏🏻
@falk0069 Жыл бұрын
in case others would like it, I posted it here: www.dropbox.com/s/km8oizbloll9u7t/Maytag_Washer_Bravos_XL.pdf?dl=0
@ulicom222 жыл бұрын
Jesus Christ thanks my lord 🙏🏼
@sasealcoatingasphaltrepair5936 Жыл бұрын
What are put it in maintenance mode it does what it wants
@jomainemilton8777 ай бұрын
How to change out the bearings on this washer
@falk00697 ай бұрын
These Maytag/Whirlpool washers all seem the same. I watched many KZfaq video showing me how to do it. I recommend you watch a few and see if you are up to it. Definitely recommend the 2x4 and carjack method to get removed. You'll find several video that explain that.
@morgenfuchs17942 жыл бұрын
Thank you!!!
@backwardsmachining75269 ай бұрын
Ty so much.
@Skinsensations_Edith2 жыл бұрын
You have the same washer as me could you please tell me what size it is? Cubic feet
@falk00692 жыл бұрын
27" wide x 27" long. 37" tall with no legs and no control panel. I have the leg screwed out for and extra inch and the the panel adds another 6".
@rosemaldonado65962 жыл бұрын
What does dL mean . My machine starts then pauses then the dL shows and that’s it. Please Help
@rosemaldonado65962 жыл бұрын
I tried your steps and door doesn’t lock
@falk00692 жыл бұрын
I don't know much about the dL code except that it means it is having troubles with the lid/door lock. If put your machine into manual maintenance mode you should be able to lock and unlock by pressing the 'water save' button. So you can test it, but I don't know the best way to fix.
@kimberlyjhoraitis5665 Жыл бұрын
@@falk0069 door lock sensor needs replacing. dont go cheap part due to module chip needs to hold onto mother board.
@mindaliadelrosario27222 жыл бұрын
Nada me adado resultado e echo todo eso y dra más de una hora lavando y no seca
@dulcejimenez83026 ай бұрын
Mine goes good up to the last ten minutes 🥴
@JasonSmith-qx3zh3 жыл бұрын
I thought to run test mode the tub should be empty???
@falk00692 жыл бұрын
It is just a workaround I found since there no drain option. Eventually I replaced the bearings and got some quality suspension rods. Problem solved (for now)
@jorgeemiliovillagomez68302 жыл бұрын
What is the part number of service manual?
@falk00692 жыл бұрын
Not sure about the manual specifically, but my washer's model number is MVWB725BW0
@anndinh102 жыл бұрын
What the year of this Maytag washer?
@falk00692 жыл бұрын
Not sure, but the model is MVWB725BW0
@asmrbre71138 ай бұрын
What is oL error
@falk00697 ай бұрын
My understanding is "oL" is "overloaded". Whereas "uL" is "unbalanced load". I've never see the oL code, but they could be related.
@8BitDerp2 жыл бұрын
where did you order your parts from?
@falk00692 жыл бұрын
Amazon. Everything was fine except for the suspension rods. Do not go cheap on them.
@robertscott82272 жыл бұрын
we have had our washer almost 9 years now , it was good for about 5 years. after that , i have replaced the shaft 2 times and the bearings 5 times . now the rotor position sensor is in need of replacing , also it shows ul about 15 minutes left on the power wash cycle. these washers are poorly engineered for sure .
@falk00692 жыл бұрын
Yeah, sounds about right. I'm at around 6 years now. It needed the bearings, shaft, and suspension rods replaced. I did these replacements twice but they only needed to be done once. I just got some bad replacement suspensions rod and it messed me up and I thought my bearing kit was installed incorrectly or was defective. I also had to replace a valve assembly due to a dripping issue. And lastly I also replaced the position sensor but I don't it was needed--just troubleshooting.
@robertscott82272 жыл бұрын
@@falk0069 hi ya i did that sensor no change piece of crap still throws the ul code . i have question when you pulled your drum out was it half full of water ? mine when i have the inner basket/drum it has water in it . i was wondering if this was intentional or do i have trapped water.
@alison_the_riot2 жыл бұрын
Ok.. Crazy question... Have the same UL ask the time. Yesterday washed a comforter and 4 pillow cases. When done.. Only 3 pillow cases. Searched my entire house thinking I dropped it. Looked everywhere. I know I put four in there. Have you ever heard of something going above and going into the side?
@falk00692 жыл бұрын
@@alison_the_riot Absolutely. I've heard many folks complaining of clothes getting stuck between the tub and basket and causing UL balance issues. I bet you are right and it is stuck there. If you watch more UL code videos I'm sure you will find examples of this.
@mindaliadelrosario27222 жыл бұрын
Yo boy a vender la mía nada meda resultado
@andradeesquivel80512 жыл бұрын
Lo puede traducir a español
@andradeesquivel80512 жыл бұрын
Traducción a español
@al138310 ай бұрын
Bearings in that particular washer is trash!!! I've been through 2 washers in 10 years!!
@falk00697 ай бұрын
totally agree. Also need to be careful with the cheap replacement suspension rods. They made things even worse for me.
@andradeesquivel80512 жыл бұрын
Tradición a español
@robbieeaves70373 жыл бұрын
Down in the hood
@johncanino66193 жыл бұрын
N’
@rustytheloverofdinosaurs10 Жыл бұрын
Rusty: "(Shy) (Rusty Wears His Long Sleeve Pajamas And He's With His 23 Siblings And They All Wear Their Long Sleeve Pajamas) Whoa! 🧡🤍!" His 23 Siblings: "(They All Wear Their Long Sleeve Pajamas) Whoa! ❤🧡💛💚💙💜💖🖤🤍!"
@AlyssaTheWasherLover1219 Жыл бұрын
Melissa The Washing Machine: "Dude! What The Heck! What Are You Doing Here?!"
@rustytheloverofdinosaurs10 Жыл бұрын
@@AlyssaTheWasherLover1219 Rusty: "(Shy) (Rusty Wears His Scientist Outfit And He's With His 30 Siblings And They All Wear Their Scientists Outfits) I Don't Know! 🧡🤍!" His 30 Siblings: "(They All Wear Their Scientists Outfits) We All Don't Know! ❤🧡💛💚💙💜💖🖤🤍!"