Mazda 3 fuel filter change

Рет қаралды 18,816

5 жыл бұрын

Mazda 3 , 2004-2009, Australian model fuel filter disconnection hacks. Please this is not a full filter replacement tutorial. Also note, the metal disconnect tool is home made.

Пікірлер: 23

@mydogzty 2 жыл бұрын

This has been on of the better KZfaq videos I've seen since 2015, just a quality how to and what not to do video nothing crazy edited just how to do the job, wonderful.

@jayedgerton3063 5 жыл бұрын

Excellent video. All the tricky points are well explained and the solutions provided are cheap and effective.

@falkononskiis4549 7 ай бұрын

The string method is ingenious. Thank you!

@teresevella5946 5 жыл бұрын

Thanks mate that was very thorough and very helpful

@gumbyistella 5 жыл бұрын

Thank you Terrence great tutorial

@zoomsday3999 Жыл бұрын

Thanks for posting this video.

@Pw-f100 Жыл бұрын

It's called a Scrivit combination screw and rivet.

@o0FranklySpeaking0o 3 жыл бұрын

Nice one, thank you 👍🏻

@BiteMeRightHere Жыл бұрын

Stellar video, thanks

@terencewbird2410 Жыл бұрын

You're welcome.

@danjoy92 2 жыл бұрын

Thanks!

@jsolo7576 3 жыл бұрын

Nice!!!!

@AutoScan.Doctor 3 жыл бұрын

Thank you very much..

@terencewbird2410 3 жыл бұрын

Glad to help.

@georgestamatopoulos4435 4 жыл бұрын

That’s great mate but where is it on the car????

@dominozonda 2 жыл бұрын

Great video! Really creative and informative I have a 2006 mazda 3 with 230,000 km I was wondering whether it's worth it to keep it and keep fixing it or not What would be your advice? And what was your experience with reliability? My wheel bearings are starting to go bad, also the catalytic converter, and the car is consuming around 1 liter of oil every 7000 km Also the right turn signal lever/switch started malfunctioning a couple of days ago (seem to be broken or stuck) I like the car but I don't know if I should keep putting money in it. Curious to know your opinion

@terencewbird2410 2 жыл бұрын

Thank you for your comments about my video. As far as advice on keeping your car or not, unfortunately I am not qualified to give that advice, as I am not a mechanic.

@dominozonda 2 жыл бұрын

@@terencewbird2410 your methods were so creative, I thought for sure you had experience as a mechanic or working in a similar field It's always tough making a decision whether to continue spending money on an old car or to move on, but I like this car so I'll try to DIY what I can to keep the cost down and hopefully it'll workout in the end How is your mazda 3 holding up if you don't mind me asking? And did you face any problems with it other than the wheel bearing?

@justincameron5902 4 жыл бұрын

I have two grey connections and can’t fit the disconnect insert on the outlet side any ideas

@terencewbird2410 4 жыл бұрын

Justin, I just did this with my "off the car" set up. I severed the filter outlet pipe between the plastic connector and the filter housing with a pair of bolt cutters. I used a pair 24"/600mm long and there was just enough room for the jaws. The next size down I think would be ideal. The outlet pipe was squashed but not cut through but 6 or so movements back and forth and it separated. This allowed me to put two flat bladed jewellers screw drivers under the grey tabs. With the tabs up I used another small flat blade to push the outlet pipe out of the connector levering off the bead on the outlet pipe. I know it will be awkward on the car but it did work. Using bolt cutters does not leave any filings or fragments. Good luck, twb