Mazda RX8 power loss (Solenoid Replacement. )

Рет қаралды 3,106

10 ай бұрын

Secondary Air Injection low "engine light" fixed! I replaced all 3 solenoids and now.. The air pump is finally working and car seems to be running great! Bought these off Amazon for 10$ each. Iv used them in previous projects and never had an issue. Hit the "like" button. It really helps out the video's! Thanks for watching.

Пікірлер: 24

@samcohen1625 10 ай бұрын

Oh jeese, what a live saver this video is. And only one day old. Thankyou thankyou thankyou. I’ve watched so much rubbish on this issue, some ramble on others are incomplete and leave you wanting more. I have the 661 code on my 04 which has done only 40k. I don’t trust mechanics round here and having an engineering background I want to do this. Firstly I noticed the ssv valve is dead. It’s not not moving but not seized. Secondly there’s no vacuum coming up the pipe to the actuator. On inspection there’s a large blockage in the tube. I can’t get it out, so the manifold has to come off. Thanks for showing this procedure so well and the care with the gaskets.

@StefanMailey 10 ай бұрын

Awww man, Thanks for the comment! Im glad it helped! It's pretty easy to do. Don't forget to be careful removing the bolts... Don't lose them! lol. Thanks again, appreciate it!

@samcohen1625 10 ай бұрын

Well, I managed to replace the solenoid your way. Now all is good. Passed emissions test. The coil was open circuit intermittently. The new one was about 40 ohms. It wasn’t easy getting the back bolts out from the manifold Lol. One more important advice regarding those nuts you mentioned. There is also a bushing or collar round the bolts, which nearly fell into in to the tube. Also, a gasket fell off from that joint. Otherwise all good.

@StefanMailey 10 ай бұрын

Thats great news! I failed to mention that I had to use a few extensions on my 10mm socket. I'm stoked you passed emissions, brother! We don't have emissions anymore here in Ontario, Canada. So thats a plus!@@samcohen1625

@sgudino1 7 ай бұрын

I am getting the P0661 code and i have the 5 bolts mentoioned in the original video, but i dont see the 2 other bolts. I plan to remove the upper air only, did you also have to remove or loosen the intake valve. i was wondering what the electrical cap was, but n ow i know its the alternator, it is real tight in the bolted down wires. Any advice? or caution@@samcohen1625

@byrongarcia5556 Ай бұрын

Are all 3 solenoids the same part number?

@StefanMailey Ай бұрын

Yes

@miguelandonie8805 6 күн бұрын

I been having my Rx8 park on my garage for 5 years . Because it dies on me while driving .. and the codes engine diagnostics talks bout this solenoid valves 😭

@StefanMailey 6 күн бұрын

@@miguelandonie8805 SSV? Code?

@miguelandonie8805 6 күн бұрын

@@StefanMailey trouble codes P0661 intake manifold P2259 secondary air injection system control B circuit low P2270 : O2 sensor signal stuck lean - bank 1 sensor 2

@StefanMailey 6 күн бұрын

Sounds like you have a air leak. Also, your cat is probably clogged. Secondary air is that silly pump that turns on on cold start ups. Id remove your cat and clean it out. gut it. That's probably your main issue. Then check vac line coming off your throttle body. If it's still connected. You running a cold air intake or stock airbox?

@miguelandonie8805 6 күн бұрын

@@StefanMailey thank you

@LuisRivera-lr7mo 2 ай бұрын

For the gaskets are there two throttle body gaskets and an intake manifold gasket?

@StefanMailey 2 ай бұрын

There are < I believe.. 6 or 7 gaskets. You mean the o-ring gaskets?

@LuisRivera-lr7mo 2 ай бұрын

@@StefanMailey Yes, I meant the o rings oops

@ve2430 10 ай бұрын

What code were you getting? Im getting p2004. I believe vdi stuck closed. Related to yours?

@StefanMailey 10 ай бұрын

P0410 was one of the main ones. Secondary Air Injection!

@StefanMailey 10 ай бұрын

P2259 also.

@ve2430 10 ай бұрын

@@StefanMailey yeah that's different than mine. Btw I made a mistake. Mine is the APV motor that controls the intake runner. Stuck closed. Do you know if I can reach it with the motor in the car? I'm waiting to break the motor in since it's been rebuilt so I can rev it over 6k since that's when that apv is activated. I'm hoping it will unstick and code will go away. If not, I will be forced to replace it but I really hope I can reach it with the motor in the car

@StefanMailey 10 ай бұрын

Is it located on the lower intake? I think you gotta pull the motor. No?@@ve2430

@ve2430 10 ай бұрын

@@StefanMailey maybe. That's going to be messed up. Just had the motor put in. Really hope it unsticks after I rev it high otherwise I can't pass emissions