Mazdaspeed 3 big turbo upgrade. Maxspeeding rods gt3582 turbo from ebay along with eBay turbo t3 manifold and eBay 38mm wastegate with 14 psi spring as well as a 4" intake and custom 3" downpipe.
Пікірлер: 51
@Mazdaspeedgarage Жыл бұрын
The mock up of turbo and flange with welding is pretty good for diy project. Garages would have charged so much for this. Keep up the good work and content it really help other mazdaspeed owners 🤘
@bigboostmcgee4211 Жыл бұрын
Thanks, that means a lot
@Mazdaspeedgarage Жыл бұрын
@@bigboostmcgee4211 where did you get the the huge 90 degree coupler and long bolts
@bigboostmcgee4211 Жыл бұрын
I got the 4" 90 on Amazon and the bolts I picked up at a parts store in the exhaust section
@Mazdaspeedgarage Жыл бұрын
@@bigboostmcgee4211 thanks 🙏 appreciate you What about the MAF hosing
@bigboostmcgee4211 Жыл бұрын
The maf is 4" o.d. from a subaru
@Reubachi Жыл бұрын
Incredible as always. Your videos legit make me comfortable knowing I have references for whenever I rebuild my 2.3
@itsyoboitonesyt64059 ай бұрын
Love this great job man
@josephsfinancialjourney10 ай бұрын
Very nice engine bay setup love the pink and gold colors
@stl_kc7184 Жыл бұрын
very good job honestly, look well put together and the fact that you can say you did it yourself it very inspiring, wish I had this skill
@bigboostmcgee4211 Жыл бұрын
Thank you, that means a lot
@stl_kc7184 Жыл бұрын
@@bigboostmcgee4211 ofc man, can't wait to see where this build goes!
@Msspeed-jj3km Жыл бұрын
Your diy work is sure inspiring and motivating man! My speeds been blown up since July 2019 :( I bought a 2.5 and slowly been hoarding parts to do the swap. How is your swap holding up?
@KFX10512 күн бұрын
Hey man I don’t know if you’re still active on here but had a few questions. -What did you do about the boost reference nipple that comes on most pre made intakes? -What’s your oil and coolant line fitting specs?
@Mazdaspeedgarage Жыл бұрын
Great video and awesome work
@SmallSonEZ5 ай бұрын
Any build updates?
@kubsterr Жыл бұрын
awesome work sir
@bigboostmcgee4211 Жыл бұрын
Thanks much appreciated
@Genwonspeed38 ай бұрын
They didn't have a banjo to AN fitting?
@n8o8n Жыл бұрын
Nice! Is a GT3582 too big? Hopefully it's not as I have one laying around... What A/R?
@juliolopez7893 Жыл бұрын
Sickkkkkk video man
@Marshallbuttholeman Жыл бұрын
I like how you did this set up. You don’t have any issues with using silicone tubing for the coolant feed and drain on the turbo? Silicone is so great with its flexibility but a lot of people say don’t use it. But if it works that’s good to know. I plan to do a top mount set up like this at some point
@bigboostmcgee4211 Жыл бұрын
Haven't had any issues so far and I'm in SW Fl where it's 90°+ most of the time
@peterxiong Жыл бұрын
Props!
@Marshallbuttholeman Жыл бұрын
Any update on how this turbo is doing? Also where did you get the intake supplies from?
@bigboostmcgee4211 Жыл бұрын
Turbo is spooling great so far. The intake is a 4" 90° elbow, 4" subaru maf housing, and a 4" k&n
@tntathean44098 ай бұрын
how long would you take to build that exact setup you have?
@bigboostmcgee42118 ай бұрын
It took about 7 hours total, 1 or 2 hours at a time
Appreciate you. Can’t wait to see the update on the car with the final tune 🔥
@alexwhite1768 ай бұрын
Im cheap so i really like this lol. Does the log manifold seem to ve the same as the factory manifold. Or is it better?
@bigboostmcgee42118 ай бұрын
It flows great
@christophererickson730029 күн бұрын
Are you still Runnig the 2.5?
@bigboostmcgee421129 күн бұрын
@christophererickson7300 yea but I'm currently building the stock block too
@MrPrado99911 ай бұрын
Any updates? Would love to hear how it sounds
@bigboostmcgee421111 ай бұрын
I should hopefully have a new video soon
@andruwwilson83678 ай бұрын
@@bigboostmcgee4211where is the new video?!?
@ntr52 Жыл бұрын
How is the 2.5 swap holding up?
@bigboostmcgee4211 Жыл бұрын
It's doing great so far, saving for a intake manifold so I can go port injection and really push it
@MegaXavier1999 Жыл бұрын
Can you use a stock flange turbo in this log manifold? If not what flange do I need
@bigboostmcgee4211 Жыл бұрын
The ebay log manifold is a t3 flange
@MegaXavier1999 Жыл бұрын
@@bigboostmcgee4211 what about the oem, maybe they have an adapter I can buy to t3 but idk the name of the stock flange I been digging trying to find it but can’t seem to find an answer, great video by the way
@bigboostmcgee4211 Жыл бұрын
@Modern Anarchist Thanks... yea, I'm not sure of the name of oe turbo flange.
@StyleGaragecc3 ай бұрын
Is this a 2.5 engine?
@bigboostmcgee42113 ай бұрын
Yea a 2.5 block with a mazdaspeed head
@StyleGaragecc3 ай бұрын
@@bigboostmcgee4211 are you able to tune it with like freektune etc?
@bigboostmcgee42113 ай бұрын
Yea, freaktune did the tune for mine
@Reubachi Жыл бұрын
Mr. McGee do you have an insta for us to follow?
@bigboostmcgee4211 Жыл бұрын
No not yet, I've been thinking about starting one for the channel