Mazdaspeed HPFP Installation + OEM vs Autotech Identification!

Рет қаралды 9,664

Graveyard Performance

Күн бұрын

Пікірлер: 35

@SpoolingUpPerformance 3 жыл бұрын

Nice video!! I’m just here to see what Andre do with dem hands thooo

@caysonstark7124 3 жыл бұрын

I already got hpfp internals but I had to watch it to support the boys!

@nolan9193 3 жыл бұрын

Haha this video is perfect lol. I literally just ordered my autotech from y’all this morning lol.

@wm052004 3 жыл бұрын

Thanks for this video. I'm looking to do this for the first time. Could you also do video of adding the E85 seals to it as well? Update, took me 5 minutes. Everything in here is spot on step by step. Had a 2nd hpfp housing to tinker with, and it was extremely easy. Thank yall again

@foxxrider250r 2 күн бұрын

What did you use to "lubricate the shaft"?

@rajfam4409 3 жыл бұрын

Nice complete instruction on hpfp installation with some jazzy music.

@sohaiinthesky Ай бұрын

do i need tune for this at all ?

@graveyardperformance Ай бұрын

No tune required for the HPFP, but we do recommend a pro tune always to make sure your car runs appropriately for your climate. You can contact us or PD Tuning for more information!

@crazyfireboy123 3 жыл бұрын

Hello! So I had to buy a new hpfp because I stripped the 18mm bolt so I got my new one and installed the hpfpi to that and I installed it and it has the normal ticking noise of a hpfp, but when I give Barry give it gas there is like a strange noise, kind of like a bb or like scraping metal I can’t really explain it, but on my accessport everything seems to be normal on wot I’m getting 1774 and idle is roughly 420-427 any ideas on what it is? I mean everything runs fine. And I already broke it in at 130 miles

@gsrjohn 3 жыл бұрын

I have the same exact issue. It kinda sounds like a hollow metal sound right? Fuel pressure looks good and I've put 375 miles on the new internals, no issues. Its just that noise..... Did you ever find out what it was?

@crazyfireboy123 3 жыл бұрын

@@gsrjohn honesty not yet, I might just take it back out and see what the problem is, I know normally those hpfpi are kind of loud, but I’m going to take it out and see what it is.

@gsrjohn 3 жыл бұрын

@@crazyfireboy123 make sure to comment back if you find something out. But the general consensus from everyone on the mazdaspeed 3 owners page on Facebook is that its normal.......there just that damn loud. And I have already put 400 miles on it with no issues. Which helps feed my paranoia.

@kwbalance108 3 жыл бұрын

Any update on the noise?

@crazyfireboy123 3 жыл бұрын

@@kwbalance108 still happens, but with my Cobb downpipe being so loud I don’t really hear it anymore

@Dragaroi Ай бұрын

Would I be able to just switch the whole pumps (stock with one that has the hpfp already installed) or would it be better to just swap it into my stock one anyway since I’m looking into getting a slightly used one

@graveyardperformance Ай бұрын

@@Dragaroi yes you can swap a pump over that already has them. Never a bad idea to rebuild or clean the pump

@ReeshaRacing Жыл бұрын

when i try to put my hpfp back on the main fuel line won’t line up and i just can’t get it in any tips please

@javierperez644 3 жыл бұрын

That white part on my blue clip fell off, will I be able to use it like that or where can I get a new clip and that white part?

@asurimramirez1249 8 ай бұрын

When I tried to put back the HPFP. I could not be able to do it due to the piston on the counter side is up. I tried to spin the crankshaft but it does not move, or down. Any other ideas to push it and install it like this video as easy?

@graveyardperformance 8 ай бұрын

Shoot us a message on our Facebook with photos of what you mean and we’ll see what we can do to guide you

@asurimramirez1249 8 ай бұрын

Great! Thanks

@channkrp 3 жыл бұрын

Nice install vid

@MZSP3MARIA 5 ай бұрын

Hey so when I try to put the pump back on, it doesn’t sit properly, it won’t even reach the dial pin without having to compress it, which I see you did not have to do here. Could it be I built it wrong or didn’t push the pin in the housing all the way? Any ideas ?

@joeespinoza6995 5 ай бұрын

Honestly it did that with my stock pump . I just pushed it in so it could be flat and then I put the screws in . As long as it’s sitting flush it should be ok