MB M157 M276 M278 camshaft adjuster

Рет қаралды 32,372

Tasos Moschatos

7 жыл бұрын

Пікірлер: 26

@lukep6017 4 жыл бұрын

Excellent VIDEO.

@youtoobe169 5 жыл бұрын

Thanks for posting. Very interesting!

@aqeebparvez3528 5 жыл бұрын

Can you please share engine timing for M276

@mahmoudabdulmoaty9965 2 ай бұрын

Did anyone try any non-OEM parts for the camshaft adjuster and how was it

@ksenofonhaskocela5687 5 жыл бұрын

Hello! I have a Mercedes W211 e280 petrol 2006 and a diagnosis with code P2090 COMPONENT 49/7, The engine light is on. I replaced the solenoid and the same result again. I can advise you how to act and who do you think is the cause of the defect. Thank you

@Miike3210 3 жыл бұрын

This is making the ticking noise at startup? Driving like this for 6 months on my c43..

@active1328 Жыл бұрын

Hi , I’m just wondering are they all the same so I could put M276 on 278 ?

@gaz31w10 6 жыл бұрын

How many km ? not repaired?

@roro85600 2 ай бұрын

P0016 C63 S IDEA TO ISSUE

@mr2dsp 4 жыл бұрын

Tasos if the cam magnet is failing will it make noise on start up. I have a rattle noise sometimes on start up.

@robertmorgan8104 Жыл бұрын

Sounds like the chain tensioners are failing. It creates a rattle.

@nebojsatanasic4112 4 жыл бұрын

One question for everybody, did anyone saw actual camshaft goes bad, not the adjuster?

@nebojsatanasic4112 4 жыл бұрын

@Phuong ?

@boonlertthepsimuang5384 5 жыл бұрын

Hello, I love all your posted, I am try to rotate my m278 camshaft adjuster pin. What is troupe value to re assemble 4 bolts on camshaft adjuster and any loctite is required? Thank you in advance.

@TasosMoschatos 5 жыл бұрын

Boonlert Thepsimuang hi, I'm not opening this type of cam adjuster because of the hard spring, when you try to put it back again it's not aligned properly, better buy a new one. Thanks

@boonlertthepsimuang5384 5 жыл бұрын

Thanks and understood.

@boonlertthepsimuang5384 5 жыл бұрын

I just got 4 new camshaft adjusters. Can you please let me know torque value “M278” for bolt (camshaft adjuster to camshaft). Also any of loctite is requires. Thank you in advance.

@SlickJeff2020 7 жыл бұрын

Hi, thanks for your educational videos on M157 engines, I have a question for you, My car has a M157 in it and its in stock condition, I noticed on cold start it makes a knocking Nosie and after I turn off the engine for few seconds and turn it back on the knocks goes away! what would you think is causing this issue?

@TasosMoschatos 7 жыл бұрын

+Jane Dogh hi, I will reply with a video most probably today

@TasosMoschatos 7 жыл бұрын

Jane Dogh kzfaq.info/get/bejne/f95_ZNuK1ZaplZ8.html

@bm-rf4bc 3 жыл бұрын

the 276.9 intake actuator is spring loaded... have a tear-down and assembly for it?

@TasosMoschatos 3 жыл бұрын

You need to fix a tool before you open the cam adjuster to hold it in place, i try before with a piston ring compressor tool unsuccessfully

@bm-rf4bc 3 жыл бұрын

@@TasosMoschatos too late for that. maybe next time!

@mr2dsp 5 жыл бұрын

Hi i got a noise on my 2013 e 350 m276 motor. It has 52000 miles and the noise sound like a chain rattle but it goes away after 4 seconds. What should i do warranty is over already. Thanks

@glasser2819 5 жыл бұрын

I had the same rattle at 25kMi only... the rattle means engine just needs better lubrication! Use thicker oil 10w40 every 7000kMi.

@maxmedo4033 4 жыл бұрын

@@glasser2819 i have the same problem, i got the noise for about 4 sec. changing the oil to thicker one dose is effect the engine?!