Hi. Just found your channel and it's excellent 👍👏👏. Got SLK 230 Kompressor year 2000 and my pump won't shut off. Tbh never knew about it existence in my Merc until one day I've been doing some work and simply disconected the battery for about day or two. Then, when connected the battery the air pump starts working immediately!!! And won't shut off. It's gonna be working till red hot but won't shut off. I've checked vacuum lines, switch over valve , this top valve , took out and check the relay plate with k40 amp relay and some fuses ( plate looks good, no damages to soldering lines, all fuses, relays ok) I've also took out pump and dissmantled to check hows things inside ( all been good, no burnings just some dust) so cleaned, put back together. AAAAND...pump is still working 🤦🏻♂️ I need to check this valve at back of the engine, cuz forget about it but honestly have no more ideas what's going on. Also got P2003-2 fault and it says about undervoltage on the sensors. I've put NEW *MAF s *CAMSHAFT s *CRANKSHAFT s *waiting for 2x MAP sensors Have no idea what's happend to my Little Bastard, all been great since last year and all of the sudden some strange things started to appears. Too long list to point out. But if someone could help with pump I'll aplreciate that 👍
@Ullakkomies3 жыл бұрын
Great video and very good instructions! You helped me to repair my 2002 CLK C200. Thank You very much! My best wishes for You from Finland. Keep going :)
@doit_vehicles3 жыл бұрын
You're welcome! glad it helped
@roddyrackz94349 ай бұрын
I have a 2004 c200 coupe. So the same as yours, but 2 years later. Do you know if your engine is the m271 or the m111?
@emirwati3 жыл бұрын
Hi Guys. Update on my previous comment. I succeeded to replace and connect loose or damaged vacuum lines, and the one I mentioned before goes to the firewall, but I don't know what is doing there. Anyway, the back headrests still do not work after this. Regarding the connector to the switchover valve, the reddish wire (red and green I think) is always negative, but the other one which is grey or white with an orange or brown line (not easy to define unless I cut the protection), don't have the positive during the first few minutes of a cold start, or so. I inspected all the relays and fuses in the boot and at the front and, in addition, two of them (K and R) were tested while plugged. Thanks, doit for your video on disassembling the intake manifold, which I partly followed to do the job. The greyish wire coming from the switchover valve seems to end up at the front fuse box; I tested one with a similar colour and it has 12V positive but it is for way too long after the engine starts. What makes me confused is that this same wire appears to have continuity with the one in the connector! I need to double-check that. I don't know yet how to connect the vacuum gauge. By the way, I have not yet tested the car on the motorway, but the idle is definitely more consistent. Regards.
@williamshanasy22885 жыл бұрын
Nice work thank you ... hope you keep warm in all that white stuff falling from the sky
@doit_vehicles5 жыл бұрын
Thanks man ! Yeah .. I will . The weather is unpredictable sometimes
@mansoorarabvlogs14544 жыл бұрын
Thank you It helped me get a good idea of the AIS system.
@doit_vehicles4 жыл бұрын
I am glad to hear that !
@ronnietan5164 жыл бұрын
Very good instruction, also applies to my 2011 W204 C180. Thank you.
@jgmat585 жыл бұрын
Very good video¡ I appreciate it a lot big effort with snow fall, keep going!
@doit_vehicles5 жыл бұрын
Thanks ! I appreciate your support ..
@jgmat585 жыл бұрын
doit_vehicles I have a C200 with m111 and your videos are very usefull!
@doit_vehicles5 жыл бұрын
That's a cool !
@megeorge41282 жыл бұрын
Thanks for the video. I learn a lot from your detailed explanation.
@robertsekrst80204 жыл бұрын
Just a site note. You dont have to remove the supply line. You just unscrew the check valve. You can do it if you make a special key by cutting a head of a if i remember 27 wrench. Mercedes mechanics of cors have access to original removal tool. The real problem is in the valve. Cleaning wont help. Its a design flaw. Over time the rubber seals wear out and the exhaust fumes will over time destroy your second purge valve. Tipically the last 60 - 80k miles. I think I have a masters degree for secondary air injection troubleshooting, as how long it took to find the problem :D
@emirwati3 жыл бұрын
Hi, doit. I always like to come back to your videos. I still have this car. After one year I have not discovered why the switchover valve connector doesn't have 12 volts when the car starts cold. Besides the three vacuum lines that go in/out of the switchover valve, there is a fourth vacuum line hanging loose underneath the top assembly, which is connected near the vacuum line plastic tube coming from the switchover valve. I don't know where the other end should go. Any help to solve these issues is welcome. Related to this matter is how to connect a vacuum gauge in this car to do a diagnostic check. Take care doit and guys, your contributions are very helpful.
@sofyanhabib35383 жыл бұрын
Thanks for your explanation
@damkhan5151 Жыл бұрын
you work veryhard outside
@Johnjones-vb3xd4 жыл бұрын
Very helping diagnostic...thanks
@Aliabd-yp7cp9 ай бұрын
The two hoses on the top of switch over valve one of them clearly i can see where it is connected to shut of valve but the other one where it goes
@emirwati5 жыл бұрын
Thanks for your explanation. I will try what you suggested.
@ED-rg3ll Жыл бұрын
Good Video 👍have a e 200 kompressor -2001 /325 500 km 💪
@quentinLsmith4 жыл бұрын
Sorry. I think you answered my question at the end of your video. Thank you for your videos.
@shanmugamsangarapillai19754 жыл бұрын
good simple explanation thanks Australia
@irenovati2 жыл бұрын
Funky Awesome video. Realy congrats!!. thank you for share!!
@5namtab5 жыл бұрын
big fan frpm day one!!! Can you do a troubleshoot video of the fuel gauge ? my car goes out of fuel 5 km after the reserve light has com on. Thanks in advance.... I know it might take some time. Cheers and very informative video as usual !!!
@doit_vehicles5 жыл бұрын
Hei ! thanks for beeing around . It sounds like there is a issue with the fuel level indicator ; until I do a video about that , you might wanna check the fuel pump assembly and test the fuel level potentiometer . Is the same as a throttle body or acceleration pedal or any other sensor Here is how to remove the fuel pump with the fuel level sensor : kzfaq.info/get/bejne/jd99ldN6udzQgnU.html Cheers !
@fbaldus4 жыл бұрын
Did this today, to clean the check valve you do not need to remove the torx holding the pipe line or check valve, just raise the car, and remove the big 27 bolt holding the fitting, you will have enough space from underneath, remove the perforated bolt, careful not to loose the two crush washers, one behind the head side and one on the other side of pipe. take a peace of 5 by 5 inch aluminum foil and slide it between the pipe and the intake manifold side, to block anything you will spray through the check valve. I used a pulverizer gun and gasoline to clean the check valve which was almost completely clogged. all the junk came out of the pipe, the aluminum foil sheets blocks all this junk from entering the exhaust system. Done! no more insufficient secondary air flow code.
@doit_vehicles4 жыл бұрын
nice work !
@georgec77983 жыл бұрын
Hi, I know you must be busy so maybe someone else can help me with this question and do a small test for me. When I unplug the harness from the switchover valve and test the two wires I'm getting 4 volts on one wire and 11 volts on the other wire, does anyone know if the voltage is correct or should I be getting 12 volts and ground?
@megeorge4128 Жыл бұрын
Dear Sir Thanks for your video. Could you do another video to replace Check Valve for the same car? Thanks
@Omurpasaoglu4 жыл бұрын
Teşekkür ederim.
@iki9118 ай бұрын
Would you have any idea why my change over valve has both wires are positive? I have a 03 c230 and 2011 c300 they both are showing positive on both wires
@liasdizon4 жыл бұрын
Where do the third line switch over valve go to?
@gaf81673 жыл бұрын
nice
@salahsaad17885 ай бұрын
What malfunctions does it cause?
@user-oc1uk1wn6n8 ай бұрын
Hi good people. I have a pipe that is hanging from my switch over valve. Please assist with connection lines. Thank you in advance
@salahsaad1788 Жыл бұрын
Please help, my car engine does not exceed RPM 40,000, what is the problem?
@rugo8414 жыл бұрын
Great video 🔧😀
@videorowtv5198 Жыл бұрын
Hi, thanks for the vid. What OBD reader app are you using?
@cloutierrobert92052 жыл бұрын
Bonjour j'ai une c230 2002 condition très bien jamais sortie l'hiver je trouve quel coûte très chair en essence que faire Merci ! pour vos vidéo je viens dans prendre connaissance
@megeorge4128 Жыл бұрын
Thanks for the video. Just one question....at 7:12, for the pipe, where does it come from? Thanks
@alrifainidal2 жыл бұрын
Great video . i got p2031 and p2036 on 2001 Mercedes c200 w203 i clear the code i tested the o2 sensor upstream by add fuel source to the vacuum line read rich when i apply vacuum it read lean . what do you think the problem thanks
@jgossy54783 жыл бұрын
Hello great video, it explained much more clearly what I needed to check, to get rid of my PO410 code. When I cleared my PO410 code, I can drive for miles 300 miles or more, but sometimes I can only drive 75 miles or less before it sets the PO410 code again. I checked everything just like you showed in the video, I have vacuum where I suppose to have vacuum, and I have pressure where I need to have pressure (on the hoses you showed). The solenoid works properly, for the required amount of time, ( I did this check after allowing the car stand over night.) Code PO 410 keeps coming back, I started having this problem at the beginning of the summer it was fine all last winter. I would appreciate any help with this problem, Thank You in advance.
@doit_vehicles3 жыл бұрын
if you say that all the tests were done ; what's left is to get a scan tool with live data and do a diagnose , see what happens when the code is trigered ( LTFT STFT ) But do you have the same engine ? or the v6 with the air pump
@ursschwarzwald5074 Жыл бұрын
@@doit_vehicleshello I want to check the valve but I don't know where's the plus and - side? Can I make destroyed the valve when I checked both sides with 12 volt?
@quentinLsmith4 жыл бұрын
Can you tell me where the bottom hose of the switch over valve connects to please?
@mecid.h343920 күн бұрын
please vehicle diagnostic program apk and link
@killerbong443 жыл бұрын
Hello , where is the secondary air pump ?
@raphaelsargeant70344 жыл бұрын
Blessing I have a 2005 ml350 W163 code P0412 secondary injection pump valve A malfunction, the pump runs every time the engine is cold all fuses are good my problem is I'm not getting 12volts at the solenoid when I crank the engine. Your answer is highly appreciated.
@doit_vehicles4 жыл бұрын
Try to inspect the wires for the selenoid to the PCM ; Is it sure that the selenoid is not activated by during a cold start ? in the video about the Oxygen sensor I do that . Basically you cehck if there is any short or damaged wires betwen the selenoid connector and the computer . Thats the only thing I can think of with these symptoms you told me .
@shany9832 жыл бұрын
Brother do you know about cold engine vibration? I have a Mercedes w203 c220 cdi. When the engine is cold, there is a strong vibration and Rpm is moving a little up and down in idle but after 30 minutes when it's warm ,the vibration is not any more. I have replaced both engine mounts , spark plugs, and a used egr installed. The car also smells badly when is start . Can you please help me?
@anibalnikov472 жыл бұрын
Please HELP, I have an issue on my w203 2001 standard, when i turn it on, and the engine is cold, it starts to shutt off the engine, i turn it on again and works fine, later on the road, when i shift to neutro it shutt off, what could it be? can it be fuel injection issue, oxigen issue? or vacuum lines issue???
@the_Zyx5 жыл бұрын
Hi! Good work, a question for you, where is the rpm sensor in w203 111.955 motor? Thanks
@lgj48144 жыл бұрын
Where does the map sensor vacum line go?
@Abangnelayan4 жыл бұрын
I have C240 2007 w203 112 engine, I have problem when the engine is running, the car shaking, I tried to unplug all coil, seems like 3 coils are broken, i have changed with new coil. but the problem is still the same. The engine on low RPM shakes the car a lot, after I try to speed in a free way, the RPM can go high as I kick down the throttle, but the speed and the power of the car wont go up. any idea why this is happening?
@doit_vehicles4 жыл бұрын
there must be done some proper testing beggining with checking the live data and read any possible codes .. it's impossible to guess what's the issue .
@Abangnelayan4 жыл бұрын
@@doit_vehicles I scanned it, it says some voltage issues spark plug) but I'm not sure about that, because after a while the engine runs normal. I tried to start the engine in the morning, same problems, engine stalling, but the engine is still on, no check engine light at the dash. I turned off the car, take out the key, and start the engine again, now the engine runs normal again.. I'm so confused
@wellingtonchanda8604 жыл бұрын
Hello Doit_Vehicles. Am kindly asking for your advice, I have a C200 2001 cl203 coupe with M111 engine and C180 2001 s203 estate wagon with M111 engine. I want to swap the engine together gear box. Can that work? Cl203 has an intercooler and s203 doesn't has. And they have different secondary pumps.
@radmansa55144 жыл бұрын
Good video 👌👌👌😎👍
@doit_vehicles4 жыл бұрын
😎👍
@lgj48144 жыл бұрын
My m111.955 has an error p0141,can you make an explanation video
@markice10113 жыл бұрын
Hi, great videos, really useful!! What scan tool / app do you use to monitor the oxygen sensor operation? Can you use the Torque android app and a generic bluetooth ELM324 OBDII adaptor?
@doit_vehicles3 жыл бұрын
The car has obd2 port . I used Blue driver which allows me to see live data of O2 . Check the playlist for the video about O2 sensors on this car .
@TheUroy5015 жыл бұрын
Jacob please I want to know what is real temperature of Mercedes 230. My is all to 85
@steveconroy16145 жыл бұрын
Time to trade up to a snowmobile ❄☃️❄🌝
@Ratkill5 жыл бұрын
Thanks as always for another great video, love my c230k and these help me keep her on the road! I do have a side question, do you know what part of the intake assembly would be called the "intake manifold runner control" valve?
@doit_vehicles5 жыл бұрын
Cool ! Very good cars and nice to work with .That's like another throttle on each cylinder at the end of the air intake manifold . Like my car does not have that - It uses the main electronic throttle to regulate the air pressure in the intake
@Ratkill5 жыл бұрын
@@doit_vehicles It turns out the cheap OBD tool was pointing to the supercharger waistgate being "stuck open". Took me entirely way too long to realise code description was just a generic reference X
@omarez68964 жыл бұрын
Was your faultcode p2006???my car (c200 kompressor)does not start with cold engine.i have to crank it for about 6 minutes before it starts.when engine is a littlebit warm it starts perfect...i was trying to find this'manifold runner control valve'
@user-qj5ku5vy6z2 жыл бұрын
Парни можно перевод всего. Я из Казахстана, часто вылазит такая же ошибка.что делать не знаю.
@justindavies47864 жыл бұрын
Great videos. What type of mods are available for this engine?
@doit_vehicles4 жыл бұрын
You meen to increase the power ? I've seen up to 280 hp models with a electric turbo and remaping
@user-lh7tp1ud3q Жыл бұрын
Where is the EGR Valve in this car?
@doit_vehicles Жыл бұрын
It does have a EVAP system since its a gasoline engine
@adamspicer763 жыл бұрын
What does the bottom vacuum hose connect to.
@doit_vehicles3 жыл бұрын
On the throttle body top hose
@lgj48144 жыл бұрын
My switch off valve exhale air,it doesnt suck air
@user-ci1ch6xk6t4 жыл бұрын
Great video as always. Could You help me with my c180 2001 petrol, OBD scanner displays P 200A error and points me to the Powertrain. What do You think I should check first? Your videos are amazing and very well explained,keep up the good work :)
@doit_vehicles4 жыл бұрын
Hei ! I am glad it's helpfull ) Can you tell what are the symptoms and if you have a Intake Manifold Runner Control system ( the extra flaps inside the intake manifold ) For example I do not have that.
@user-ci1ch6xk6t4 жыл бұрын
@@doit_vehicles Well on cold engine when accelerate hard instead of more power the front end stomps to the ground. If I accelerate slowly everything is ok. It feels like there is some vacuum leak from somewhere. Changed the MAF with new, cleaned the throttle body, yet the problem still there. Not variable RPMs on start up.
@doit_vehicles4 жыл бұрын
If you suspect a vacuum leak spray some gasoline around that area while watching the oxygen sensor response or LTFT STFT .. Fuel pressure under a load might be also a factor ..
@emirwati5 жыл бұрын
Hi doit_vehicles I got a P0410 code related to the Secondary Air Injection System. I followed your video and, apparently, all these valves work. I could only find (confirmed) that there is no power in the switchover connector when I start the engine cold. What shall I do next? Thanks in advance.
@doit_vehicles5 жыл бұрын
Hei ! It's quite hard to tell without seeing the car , did you check as well the canister ? also check if you have another selenoid attached to the canister (some models have it ) And if you have a scan tool you might check the freeze frame ..
@emirwati5 жыл бұрын
@@doit_vehicles Dear doit_vehicles Thanks for your reply. I have a picture, drive.google.com/open?id=1VUXg4xyCWM-91BJUrq6eu4nkLfiVZRU- ; I think my car is like yours, I don’t see any canister. I followed your video and tested the valves, the shutoff valve like you did in the snow with a syringe, but for me, in Malaysia, it was hot, no snow but mosquitoes. For the check valve, I used a bicycle pump connected to the pipe and the air was flowing. For the switchover valve, I used a multi-meter and a 12V supply; I could hear the click and there was some electric resistance. The scan tool gave me the codes P0410 (secondary air injection system) and P0172 (system too rich), that’s why I went to investigate. Finally, I noted that the connector to the switchover valve doesn't have current when I started the car from cold; I confirmed this a few times because I was afraid the multi-meter probes were not properly connected, therefore I used pins inserted into the connector. I am very grateful if you can show me the next step. Regards.
@doit_vehicles5 жыл бұрын
Hei emirwati ; I confused the Secondary air injection system with evaporative emission control system ... sory . It's very possible from what you describe that the swithch selenoid (the one you tested ) is not allowing the air to go into the exhaust therefore the oxygen sensor is getting hot slow and the engine must run on "open loop" injecting more fuel ; So after all this the oxygen sensor whe it gets to working temperature it reads rich in fuel - therefore the code p0173 . Now the next step is to find out why there is no power at the connctor . Try to test the continuity betwen the connector from the selenoid and the one to the PCM . Than when you find out which pin are (on the PCM) do a voltage test there . That can be a first step ; A shorted wire can be a plausible cause to this issue , especially in a hot weather with mosquitoes like yours )
@cilkitzvictoria45863 жыл бұрын
Yes sir, can you help me out ,i have problem of my 2009model c200 kompresor, troble code p0045 ,its say super charger boost control solenoid circuit A / open, where can see the boost control solenoid
@doit_vehicles3 жыл бұрын
it's right after the air filter - it looks like the throttle body
@cilkitzvictoria45863 жыл бұрын
@@doit_vehicles I cannot see it,with this model,2009 c200 kompresor,tnx anyway sir
@cilkitzvictoria45863 жыл бұрын
You mean the air flow sensor or map sensor
@doit_vehicles3 жыл бұрын
@@cilkitzvictoria4586 2009 has a slightly different engine: Look for the solenoid which switches the kompressor . Its vaccum actuated and it should be somewhere around the kompressor
@cilkitzvictoria45863 жыл бұрын
@@doit_vehicles sir,can i send a video of my car
@o.b.aoyinloye25913 жыл бұрын
I run with catalytic converter deleted. Hence I can spray the injector cleaner voila! Thanks
@doit_vehicles3 жыл бұрын
Lol
@zhandoskossakbay6175 жыл бұрын
Good job bro. Where do you live?
@doit_vehicles5 жыл бұрын
thanks , Oslo
@zhandoskossakbay6175 жыл бұрын
@@doit_vehicles wow really. Great. Never been there. In the future maybe will visit.
@gansanchis3 жыл бұрын
Good day! The shutoff vavle open only in first 150 seconds? When else and why?
@doit_vehicles3 жыл бұрын
The purpose is to reduce emissions when the engine is not running in Closed Loop ( O2 sensors are not yet on the operaring temperature)
@gansanchis3 жыл бұрын
@@doit_vehicles When else??? only cold starting?
@doit_vehicles3 жыл бұрын
@@gansanchis yes , only cold starting
@gansanchis3 жыл бұрын
@@doit_vehicles thank you. Please give your mail.
@gansanchis3 жыл бұрын
@@doit_vehicles send your mail please: gansanchis@mail.ru