No video

Mercruiser Impeller Changeout

  Рет қаралды 28,981

Adventures of Happy Ours

Adventures of Happy Ours

2 жыл бұрын

Changing the impeller on my 2006 Mercruiser 6.2 MX Horizon. This is the standard motor on many mid size cruisers like my 341 Meridian sport bridge.
This raw water pump is difficult to get to sandwiched under the motor and behind the cool fuel module. We can either disconnect all the hoses and pull the entire pump or keep in place and just pull the pump cover to access the impeller. I opted for the latter due to difficulty reaching the pump hoses and drain lines for the air purge system.
I’m using the Quicksilver water pump repair kit amzn.to/39DKc44. Use this link to order and help out the channel!

Пікірлер: 26
@otiebars32
@otiebars32 Жыл бұрын
It's always great to have someone take their time and make these types of videos to help other people out.
@chrisgolden2698
@chrisgolden2698 11 ай бұрын
That was extremely helpful changing the impeller on my remanufactured 383. Thank you!
@user-qs6vj7xx5u
@user-qs6vj7xx5u 4 ай бұрын
Just about to start work on my Maxum 2700, your video was very helpful...Thank you
@user-mj4mw3fb2q
@user-mj4mw3fb2q 11 ай бұрын
Funny how you kept saying "not alot of room". The amount of space you have is a wet dream compared to my wakeboard boat vdrive. Anyhow thanks for taking time to make/post.
@AdventuresofHappyOurs
@AdventuresofHappyOurs 11 ай бұрын
Yes it’s all relative. Lol. As I get older it gets tighter. Lol
@stevebell2999
@stevebell2999 Жыл бұрын
Excellent advice and demonstration. I have exact same engines on my ‘04 Carver.
@mchaves7663
@mchaves7663 Жыл бұрын
This is by far the best video on this subject. Thanks very much for that
@brettgerber795
@brettgerber795 Жыл бұрын
Great video. I didn’t know the impeller direction can change (at least on some models right). I have always used 2 zip ties to compress the vanes of the impeller to slide it in the pump similar to using a ring compressor when installing a pistons into a cylinder.
@AdventuresofHappyOurs
@AdventuresofHappyOurs Жыл бұрын
I’ve tried that too. I always tried to put in the correct direction but at least this model self corrects.
@OutOnTheReef
@OutOnTheReef 2 жыл бұрын
Wow cap. That impeller is in a tight spot 😳
@1951RKP
@1951RKP Жыл бұрын
I watched a video where a guy tapped out the part of the pump with the hose barbs so he could put the small housing bolts in from the front side rather than having to reach under to the back side. I’ve changed hundreds of Bravo style pumps old style and the new style like this one and they are always a pain to do. I’ve got to do a 2006 Meridian 411 with 8.1 in the next few weeks.
@AdventuresofHappyOurs
@AdventuresofHappyOurs Жыл бұрын
Plan B was to tap them out. Using the original setup with new hoses was easy enough and didn’t leak so I’m going that route for port engine next week.
@mchaves7663
@mchaves7663 Жыл бұрын
Would you post a link to this video please?
@sharronhumphries6727
@sharronhumphries6727 Жыл бұрын
Thank you for sharing !!!.
@dougmckenzie4589
@dougmckenzie4589 8 ай бұрын
Thanks mate!! Great explanation!! 👍👍
@Sailing.Artemis
@Sailing.Artemis 2 жыл бұрын
good job, and a very goo how to
@stephenj8576
@stephenj8576 11 ай бұрын
Nice vid, starting to get to know the channel
@AdventuresofHappyOurs
@AdventuresofHappyOurs 11 ай бұрын
Welcome aboard!
@ronaldhidde7119
@ronaldhidde7119 4 ай бұрын
Feel lucky you don't have "V" drives and have to remove exhaust. A total PITA!!!
@drizler
@drizler Ай бұрын
How long do these impellers last generally. I just gor a bravo 3 and am only familiar with the Alphaand its quirky pump.
@AdventuresofHappyOurs
@AdventuresofHappyOurs Ай бұрын
3 years is a good changeout schedule. Or 300 hours. Whichever comes first. You then should never have a problem from my experience.
@slosher42
@slosher42 Жыл бұрын
if you would have taken the hose off the back housing and pulled it out it would have been a lot easier.
@AdventuresofHappyOurs
@AdventuresofHappyOurs Жыл бұрын
I’ve done it both ways. Both suck. Lol.
@MaxOpticalDowningtown
@MaxOpticalDowningtown 2 ай бұрын
He was another video doing it the other way, I just did mine and it is a PITA.
@steveede1823
@steveede1823 10 ай бұрын
Just curious what are your water psi cruising? Im getting 11 on one engine and 20 on the other at 3700rpm. Thinking i should do the impellers. Temps stay at 160. Same engines and year as you. New to me boat this year. Great video!
@AdventuresofHappyOurs
@AdventuresofHappyOurs 10 ай бұрын
Not sure what they read at speed but they are similiar.
IQ Level: 10000
00:10
Younes Zarou
Рет қаралды 13 МЛН
Doing This Instead Of Studying.. 😳
00:12
Jojo Sim
Рет қаралды 32 МЛН
Comfortable 🤣 #comedy #funny
00:34
Micky Makeover
Рет қаралды 16 МЛН
Survive 100 Days In Nuclear Bunker, Win $500,000
32:21
MrBeast
Рет қаралды 153 МЛН
IMPELLER - Everything you should know
15:06
Sail Hub
Рет қаралды 15 М.
Marine Exhaust Manifolds. How Do They Work?
12:42
Schneids15
Рет қаралды 328 М.
How to replace an impeller on a Mercury inboard
14:10
GT's Performance
Рет қаралды 462 М.
Mercury Mercruiser Raw Water Pump Rebuild 2001-2016 ish 8.1 5.0 5.7 6.2 8.2 4.3
13:38
Most Common Mistakes Working With Fiberglass!
29:56
BoatworksToday
Рет қаралды 764 М.
Raw Water Impeller R&R
11:45
duboisdl
Рет қаралды 176 М.
REVIEW: Everything Wrong With A Mercury Mercruiser
15:47
DEBOSS GARAGE
Рет қаралды 225 М.
Mercruiser Alpha One Gen 2 Impeller Repair
25:47
Jonathan McClure
Рет қаралды 266 М.
Mercruiser Raw Water Pump Impeller Replacement Tricks
15:36
2stroketurbo
Рет қаралды 14 М.
How to Repair and Replace Sea pump & Impeller on Bravo 3 MerCruiser
15:12
Onboard With Eddie
Рет қаралды 173 М.
IQ Level: 10000
00:10
Younes Zarou
Рет қаралды 13 МЛН