Mercury V8 250 Pro XS 300 HOUR & 100 HOUR SERVICE *IN DEPTH*

No video

Mercury V8 250 Pro XS 300 HOUR & 100 HOUR SERVICE IN DEPTH

Рет қаралды 3,997

DSBASSGUIDE

Күн бұрын

I will post parts list later tonight.

Пікірлер: 33

@bobbarnhill8557 13 күн бұрын

Also make sure your turning the fly wheel in the correct rotation. This will make sure the impeller doesn’t get messed up when install the alternator belt. Use a little dish soap on the impeller and housing . it’s makes it super easy to install. Great DIY video.

@kz3048 5 күн бұрын

Great video... Thanks for sharing. One other item I would add to check on your 100/300 hours is to inspect your water filter. Depending on the model of your merc you might have one or two of these filters. They are just meshed plastic and can be cleaned very easy and if you fish in a lot of slop you would be surprised how much crap gets caught in there...

@calebconrad65 6 ай бұрын

Great video! Concise yet informative. I hate when guys ramble for 5 minutes before showing the actual maintenance lol.

@dsbassguide 3 ай бұрын

I appreciate it!

@tristanschaper281 6 ай бұрын

I think you did an awesome job of explaining the entire process and every step! I like how you showed the maintenance decal and walked everyone through each step on what's needed. Removing the lower unit and doing the water pump, you did a great job of explaining. You mentioned that was your "300 hour service" that you did at 248 hrs. How many times have you replaced your water pump impellor so far? It sure looked brand new when you pulled it out. It's always peace of mind to change it anyway, and to make sure the lower unit doesn't get stuck in place either. Overall awesome video! Thank you so much for taking the time and posting this!

@dsbassguide 3 ай бұрын

Thanks dude!

@TiggyTigg_6969 5 ай бұрын

Awesome video!! Havent found a video on the 300 hr service. Definitely subscribing

@dsbassguide 3 ай бұрын

Thank you!

@user-lg1we1qw1j 4 ай бұрын

Excellent 👍🏻👍🏻👍🏻 thanks for the info!

@dsbassguide 3 ай бұрын

Thanks for watching!

@rdonner28 2 ай бұрын

Great Great detail video! I myself will do everything BUT taking the Lower off 😂. U made it look achievable but I’d have something kick my butt lol. Thanks for sharing!!!!

@sterlinghancock1157 3 ай бұрын

EXCELLENT VIDEO! great info on DIY!

@JaniceAleksivich 13 күн бұрын

Very well done sir!!!! Easy to follow along, video quality excellent. 30 mins. may seem like a long video to watch but it covered all aspects of a 300 hour service concisely. Getting the back hose off the fuel separator is a biatch and I know you could not show it due to the tight space and need for two hands. Do you have any tips?

@dsbassguide 6 күн бұрын

My tip is to be patient with it, it is not easy😂😂flathead screwdriver goes a longgg ways

@finleyhascats725 2 ай бұрын

Do you have the engine in neutral when you drop the lower for the water pump? Great video!

@craigcameron9676 6 ай бұрын

leave that damn orange cap off seen them spin off get chewed up and sucked into the ihtake

@dsbassguide 6 ай бұрын

good to know!

@Fishin4truth Ай бұрын

I have this mercury engine and i cant break loose the nut...im guesiing its over torqued ...any suggestions

@JaniceAleksivich 13 күн бұрын

One other question, how do you check engines hours? I have a 2022 Ranger Angler 2080 with a Merc 250hp Pro XS 4 stroke.

@dsbassguide 6 күн бұрын

I have a Mercury smart craft gauge that tells me the hours everytime I start my motor, if you don’t have one you have to take it to an authorized Merc dealer and they’ll plug it in to tell you

@BwagMx17 2 ай бұрын

Parts list? I’m trying to find a 300hr service kit for my 250proxs with a sport master lower but the only kits I see are for a torpedo lower. Any help would be awesome, thank you!!

@ryanmeyer102 3 ай бұрын

Whats the best thing to use for a DIY lower unit stand?

@dsbassguide 3 ай бұрын

I just used scrap pieces of 2x4. I believe I had to make the top slot where the lower rests on like 7.5" wide which was wide enough to fit it in but also small enough to hold it.

@hardleon 3 ай бұрын

Where do you get that flywheel tool?

@mikejackson4146 6 ай бұрын

When you put your gear lube back in your case isn't leaving the motor trimmed up putting too much lube back in the unit or does it matter how the motor sits when the oil starts to come back out ?

@dsbassguide 6 ай бұрын

Good question, it doesn’t matter either way it fills the lower with the proper amount of lube. With the top whole vented it lets out any excess that it doesn’t need.

@stilltuckered 4 ай бұрын

Which grease did you use?

@ryanmeyer102 3 ай бұрын

What is the part number for the thermostat kit?

@dsbassguide 3 ай бұрын

8M0162139

@ryanmeyer102 3 ай бұрын

@@dsbassguide does it come with the hose clamp?

@ryanmeyer102 3 ай бұрын

@@dsbassguide or is the one with the housing necessary

@ryanmeyer102 3 ай бұрын

@@dsbassguide or is it the same thing