MF135 Restoration #13 Fitting the Crankshaft

Рет қаралды 27,071

Bundy Bears Shed

5 жыл бұрын

Fitting a Perkins engine crankshaft
In this video I fit the crank and check bearing clearance and end float.

Пікірлер: 29

@patrickflaherty3464 Жыл бұрын

Great videos lance Very clear and a pleasure to watch

@BundyBearsShed Жыл бұрын

Glad you like them!

@charleshart6992 5 жыл бұрын

Hi Lance - more great work, you certainly make these videos a treat to follow!

@BundyBearsShed 5 жыл бұрын

Thanks Charles, Glad you enjoy them.

@duncanrose3891 5 жыл бұрын

Nicely done Lance. I'm catching upon some early vids l missed. Have never removed liners or used rope gaskets so really valuable info. Thanks :)

@AmateurRedneckWorkshop 5 жыл бұрын

G'day Lance. Things disappear when I work on them also. I bet the last guy had my kind of luck.

@ShainAndrews 5 жыл бұрын

I figure that's why you guys record your work. So you can either remember what you were doing, or prove your sanity when something is not there during re-assembly :-)

@BundyBearsShed 5 жыл бұрын

Well it certainly helps, I do look back to check things at times.

@darrenblattner2508 5 жыл бұрын

Looking good Lance, by the way, my wife is in Australia somewhere on a holiday for three weeks, I should have gone with her.

@BundyBearsShed 5 жыл бұрын

Yeah you should have and come to Bundy for a look.

@dpsears240z 5 жыл бұрын

Looking forward to hearing that Perkins engine breath again.

@BundyBearsShed 5 жыл бұрын

It will be a while but it will go for sure.

@ianbertenshaw4350 5 жыл бұрын

There are a few types of those wax gauges , all work the same and the one i last used was ( i think ) plastigauge . Same stuff as the acl but i believe U.S made .

@BundyBearsShed 5 жыл бұрын

Yes mine is ACL

@bigears4014 2 жыл бұрын

Ive tinned the backside of thrust bearings to adjust the gap

@BundyBearsShed 2 жыл бұрын

ok not seen that before.

@oldironfarming5804 5 жыл бұрын

The wear on the thrust washer surfaces would be due to the pressure from disengaging the clutch I suppose?

@BundyBearsShed 5 жыл бұрын

Yes I would imagine so and when you start your tractor with your foot on the clutch before it has built up oil pressure.

@assumptavaughan887 3 жыл бұрын

Hi lace. I notice your main crank cap bolts had no lock tabs to begin with but you added some after. Do these need to be added or was it an after thought you had. Also does the bolt torque remain the same when their added. Reason I ask is my engine hasn’t got tab washers but I am wondering if I should add them. Great work as usual lance.

@BundyBearsShed 3 жыл бұрын

I think they should have had them but the tension stays the same. The tension is worked out on bolt stretch I believe.

@assumptavaughan887 3 жыл бұрын

@@BundyBearsShed Thanks for the response . I might add them while I am at it so.

@daveklooster4905 5 жыл бұрын

Are oversize thrust bearings available if a person wanted to decrease the end play?

@BundyBearsShed 5 жыл бұрын

G Day Dave, Yes Sparex have a 0.0075" oversize thrust available but none in Australia and Quality Tractor Parts in Ireland have a set of 0.007" genuine Perkins available and as I have a QTP order going in I will order some 0.007" oversize ones. 0.007 seems an odd size like I thought 0.005" may be but the 0.007 will put me right at the low end so ideal really.