Miata speaker upgrade: 90-93 NA6 (as shown) / 94-97 NA8 (requires door panel removal).

No video

Miata speaker upgrade: 90-93 NA6 (as shown) / 94-97 NA8 (requires door panel removal).

Рет қаралды 16,257

Miata Man

Күн бұрын

Пікірлер: 31

@inspace2541 8 ай бұрын

Not even a minute into the video and I already know that you’re very good at what you are doin. Keep up the good work man👍🏼

@MiataMan 8 ай бұрын

Thanks for your kind words 🙏😊

@milovan8565 7 ай бұрын

Very good video. Suggest adding the XTC foam speaker baffles to act as the same type of rainshield with bottom half cut out as seen on the back of the original speakers you took out (at the 3:05 mark).

@MiataMan 6 ай бұрын

Great suggestion on the XTC speaker baffles 👍👍

@ThatRedNismo 4 ай бұрын

This is a great video, both for installing speakers on this car, and for how to wire in speakers with aftermarket connectors.

@MiataMan 3 ай бұрын

Glad you liked it!

@joaoaoj100 Жыл бұрын

Did an aftermarket install on mine, didn't install any water shield, got a blown speaker now due to water damage

@danielskrskr 3 жыл бұрын

Cool video! How are the speakers holding up?

@oCaptainW 9 ай бұрын

Hey Miata Man, do you know if the Speaker Panel Grille is replaceable? By the looks of the video it doesn't seem accessible.

@Davestreak 2 жыл бұрын

Ill be trying Eton 16,5 cm 2 Ways, hope their good

@teganshone5778 2 жыл бұрын

My 1990 miata right speaker isn’t working, it’s only receiving 0.9 volts and there is full continuity any recommendations?

@MiataMan 2 жыл бұрын

It could be a bad channel in the head unit. The original OEM radios sometimes have this issue.

@ddaattrroonn 2 жыл бұрын

Mine is the same. Low voltage at the wires and the speaker tested good. I'm assuming the right channel is bad and replacing the radio.

@timothystrunk7323 4 жыл бұрын

Very good video

@seriouscatisserious 2 жыл бұрын

I'm getting horrible buzzing from the edges of the speaker and/or tweeter. Any way to modify this situation so the speaker isn't hitting the cover?

@MiataMan 2 жыл бұрын

Yes. Quite often, the tweeter on coaxial speakers hits the plastic support that goes across the speaker cover. You can cut it out where it attaches at the edges. I sometimes use my pruning shears or a pair of sharp wire cutters to snip the four points of attachment.

@seriouscatisserious 2 жыл бұрын

@@MiataMan Thanks. I think it's actually the foam around the speaker hitting the too-small ridge that hits it. Also, the outer edges of the bracket buzz against the metal. Are you aware of any aftermarket brackets which give proper space for the woofer and tweeter?

@Zer0CooLZA 2 жыл бұрын

@@seriouscatisserious buy a speaker with a grill and modify the plastic cover that the old grill is on by mounting the speaker on top. (that's how my Miata was done). You may want to look into some sound dampening for the inside of the doors though, there is a bit of vibration on mine at loud volume.

@ParrugTV Жыл бұрын

@@MiataMan Do you talk about chopping off the tweeters or modifying the speaker grille here? Got a pair of Rockford T1675s that has a tweeter that protudes alot, not even close to fitting.

@rauldeu719 3 жыл бұрын

What connectors do you need for the wires?

@marijapetrenko6828 10 ай бұрын

Is the speakers that you installed have a good sound when driving on highway with the top down/wind blowing? I’m trying to replace my speakers, and not sure which speakers are a good choice

@MiataMan 9 ай бұрын

These ones sounded great. There are so many speaker options out there, so it’s hard to pick. A lot of it depends on how much power you are running though them. Alpine speakers are always a good choice though.

@HarryLees 4 жыл бұрын

i was going to do this in a month or so, great tutorial. I've herd most speakers don't fit as they're too wide because the door is thin, is this a problem?

@MiataMan 4 жыл бұрын

Hi Harry, thanks for the positive feedback 🤝👍. 90-97 Miatas will accept most 6.5” speakers. There is lots of room inside the door to accommodate deeper, more powerful speakers. The window track is far enough away from the speaker hole, that there is no contact when the window is rolled down. If your speakers have a protruding tweeter, you may need to trim the plastic framework that supports the black metal grill on the factory speaker cover.

@gatorcellman 3 жыл бұрын

Would it have been good to run a bead of silicone around the speaker to seal it (better sound)?

@MiataMan 3 жыл бұрын

Couldn’t hurt. Not sure if you would notice a difference though. It would depend how much power you are running, speaker type and if the doors have Dynamat installed.