Cat 6 extension: www.amazon.com... USB-C to USB splitter: www.amazon.com... Midland MXT 275: midlandusa.com... Midland MXT 575: midlandusa.com...
Пікірлер: 28
@thecrakmasta28 күн бұрын
Dude.. what a cool idea and great clean install. So glad I came across this.
@jesuspompa14737 ай бұрын
“Cat 6, Cat 5” as you stated is a cable type. The connection is an RJ45 connector.
@azbackroadadventures7 ай бұрын
Awesome. Thank you for the correction. I learned something new. I always try to use the correct terminology but sometimes get it wrong.
@douglasstewart4066 Жыл бұрын
Thank you for sharing this. This is the most helpful video that I have found. Excellent video.
@azbackroadadventures Жыл бұрын
Thank you very much! Glad it helped.
@InGratitudeIam11 ай бұрын
Whenever you run a penetration through a seal, as with a rubber grommet, always run a drip loop. In other words, run your wire past the point of entry by about an inch or two, and then come up to the point where you're running the wire through the firewall. Also put silicone grease around the wires/cables/hoses going through the grommet.
@azbackroadadventures11 ай бұрын
Thats a great tip! Thank you.
@Christina-eh4sq Жыл бұрын
That’s awesome, thanks for sharing! I can’t wait for the next wrench fest so I can get mine out of the center consul and concealing mounted!
@azbackroadadventures Жыл бұрын
Let me know if you need help or have questions!
@willm8021 Жыл бұрын
So -for next time- that nub you ran the wires under is meant to have the tip cut off and wires ran through it. Its a direct firewall pass through that Toyota put there to prevent people from cutting holes is the boot. After you run the wire through, zip tie the outside of the nub to keep water from passing through.
@azbackroadadventures Жыл бұрын
That is good to know! Thank you.
@ericconklin61956 ай бұрын
Clean install
@azbackroadadventures6 ай бұрын
Thank you. And thanks for watching!
@josecolon3356 Жыл бұрын
Did the A.C. / heating duck when in use create a problem for the radio? The blowing of cold or hot air on the radio. Love the video, great job. Thank you help me alot
@azbackroadadventures Жыл бұрын
No issues at all! The radio has continued to work flawlessly!
@journeytoliving7344 Жыл бұрын
What phone mount are you using? I have the bracket. But need the rest assembly you are using? Thank you for your videos they are very helpful.
@azbackroadadventures Жыл бұрын
Glad my videos are helpful! The mount is the DMM from thetacogarage.com and i am using the small magnet mount. For the radio hanger i just took a piece of flat strap and drilled some holes in it, unscrewed the magnet and screwed it in.
@ag13827 ай бұрын
Epoxy, bad move if you ever want to remove.
@azbackroadadventures7 ай бұрын
I think for the cost of the blank and the cable if i ever decide to move or remove it i will be ok with it. Better than it rattling loose with super glue or something similar like what happened on another vehicle.
@amdgamer19907 ай бұрын
Midland-china crap
@azbackroadadventures7 ай бұрын
Please see below straight from their website. So either they are falsely advertising or you are misinformed. I would be genuinely curious to know which one is correct “Midland Radio is known as the first CB radio manufacturer in the United States, highlighting their expertise in American-made CB radios.”
@jesuspompa14737 ай бұрын
Send me the link of an American made GMRS radio.
@ThatCleanMT Жыл бұрын
Insane amount of work to get that extension cable into the plate. Why didn’t you just buy one in the premade RJ45 pass through plate?
@azbackroadadventures Жыл бұрын
Couldnt find one at the time. Do you happen to have a link? Would love to check them out.
@MRBIG-lg9zl Жыл бұрын
@@azbackroadadventures The eBay ones don't work fyi...