In this video Bruce will go over some tips and tricks for adjusting speed and voltage when MIG welding.
Пікірлер: 28
@StupidEarthlings5 жыл бұрын
Actually, 6.6" × 10 is: (3,2,1..) 66 inches per minute. ;)
@TheMaddogronh3 жыл бұрын
It was so different I liked it.
@jakewinkler85419 жыл бұрын
out of all the welding training I have had never did the timing of the wire feed come up. Who really cares how many feet of wire you use that number has nothing to do with making a good weld. you could have no numbers what so ever on that dial just a min and max and be able to adjust it to get the feed rate you want.those numbers are there to make for easy reference
@prostart5679 жыл бұрын
made u guys gotta work on ur editing
@StupidEarthlings5 жыл бұрын
3,2,1.. you guys gotta work on your editing.. ;)
@eksine4 жыл бұрын
5,8,7, here are the 3 aliens, 3,2,1
@danburch99899 жыл бұрын
Voltage and amps are related to each other; increasing voltage causes an increase in amps.. Wire speed has nothing to do with it. My understanding from other professional welders is that wire feed speed requirements is based upon the voltage setting for the thickness of the metal. Thicker metal requires higher voltage/amps. That necessitates higher wire feed speed.
@tapoole20009 жыл бұрын
what a joke! Watch Jody over @ weld tips & tricks for a better explanation.
@bobd.fletcherjr49122 жыл бұрын
🇺🇸👍👍👍👍👍👍👍👍👍
@ayeshemeraorecna9290 Жыл бұрын
Voltage and wire speed vertical
@akjeff643 жыл бұрын
he never even said how long the piece of wire was...
@NOOne-im5vg4 жыл бұрын
If I were you I'd give up.
@deshawnfrank9443 Жыл бұрын
I never know how to set up my mig welder
@jraposo911 Жыл бұрын
Watch and learn from this guy😊
@bobcain72872 жыл бұрын
3..2..1
@schwolneck19 жыл бұрын
Stick out is way too long
@pierdolio9 жыл бұрын
This is an amateurish presentation.
@lonniechartrand3 жыл бұрын
This video should be removed or severely edited! It is VERY CONFUSING! Should have stopped after wire feed for six seconds, times ten to get INCHES OF WIRE FEED PER MINUTE.
@longevitywelding3 жыл бұрын
Thanks for your feedback. Will address it with welder.
@jraposo911 Жыл бұрын
I am really messed up now😢😢😢
@jamessurname22852 жыл бұрын
This video isn’t correct, you don’t go from short circuit to globular to spray just by changing voltage. You can’t even get into true spray without the correct gas mix.
@samuelhara48744 жыл бұрын
This poor guy isn't bad at wleding just not good at explaining his craft
@tommo27859 жыл бұрын
you can't even multiply by 10, why should we trust the rest of what you say? 6.6 inches in 6seconds does not give you 60.6 Inches per minute I am referring to 11:11
@danburch99898 жыл бұрын
+James Thompson ... and at 7:52, he translates 8.1 inches of wire in 6 seconds into 81 feet per minute. There's an old saying that goes like this: "Those that can, do. Those that can't, teach." Apparently, he can do neither.
@brianmurray667 Жыл бұрын
Sorry, it hasn’t added one thing to my welding knowledge only confusion.
@carlmcferran93713 ай бұрын
Possibly one of the worst videos on welding I have ever seen