MINI Cooper N12/N16 Timing Chain Replacement (Non S)

Рет қаралды 15,432

7 ай бұрын

Here’s the timing chain replacement process on the N12/N16 engines. They maybe be slow engines but they are super solid from my experience
These non turbo engines are equipped in the following models
R55 Mini Cooper Clubman
R56 Mini Cooper Hardtop
R57 Mini Cooper Convertible
R58 Mini Cooper Coupé
R59 Mini Cooper Roadster
R60 Mini Cooper Countyman
R61 Mini Cooper Paceman
For reference the procedure is identical to the N18 Timing Chain replacement. Same torque specs and all, just different valve cover and intake and exhaust setups
Obviously half of the engine is different but procedures are all the same concept

Пікірлер: 56

@hugogong5627 7 ай бұрын

Thank you, Zevi! This video is immaculate with high resolution. I extracted much useful information from that.

@zevisgarage 7 ай бұрын

Thank you! Hope it helps with your endeavors!

@Braj651 6 ай бұрын

So some kits come with new cam gears both intake and exhaust. Just to be clear u would install new bolts for cam gears and what about replacing cam gears as well. Thanks again. Ed

@zevisgarage 6 ай бұрын

@@Braj651 it’s a must. They are stretch bolts

@granthansen7438 6 ай бұрын

Excellent video very easy to understand and so informative, end of this coming summer in the uk i am planning on pulling the subframes and renovating bushes paint etc, while the front is off clutch and timing chain will be done at the same time!!!!. so glad i found you Zevi you have a new sunscriber here from the uk!!!!!!!!. x😄

@zevisgarage 6 ай бұрын

Cheers! Glad to be able to help! I gotta do bushings on 2 of my other Mini’s next

@ashishm8850 7 ай бұрын

Excellent video. Much appreciated!

@krashrambo513 Ай бұрын

thanks so much for this video. you make it look so easy and explained it very well.

@zevisgarage Ай бұрын

Thank you! That’s my goal, it can be tedious for first timers but it’s not bad when laid out clearly

@perrojefe6669 4 ай бұрын

gracias , voy a intentarlo en un mini cooper del 2007 con 200.000 km , motor n12 b16 , thank you brother from spain

@alexh10001 7 ай бұрын

Thanks for showing a non turbo, hard to find repair videos for the non turbo. Any reason you did not use the cam locks instead of the adjustable wrench? Are you afraid the cam locks may break when removing the sprocket bolts?

@zevisgarage 7 ай бұрын

It’s a habit I have from when I do most rebuilds and valve stem seals from where the cams usually need to come out anyways

@Boyscout53 2 ай бұрын

This is south korea ! Good job!!

@Braj651 6 ай бұрын

Hey zevi. Great video on the mini time chain replacement. I’m going to attempt it. Just wondering if you recommend new bolts for intake and exhaust cam gears at top of engine. I know you used a brand new cam, crank pulley bolt. Ty. Ed

@zevisgarage 6 ай бұрын

Yes always new for cams, and crank

@JeanReneMartin 3 ай бұрын

Great vid Zev ! Have a QUESTION for you. Did everything in order and all but when came time to unscrew the crank bolt to release the chain, the whole thing turned, bolt and crank. Realized that the lockpin was not all the way in. Tried to put the pin in by turning the crank again and level the pistons, but it just wont go in. There does not seem to be any angle on the crank that the pin will fit. Tried to sand the pin down like some recommend, still wont go in. Have any idea what's wrong ?

@zevisgarage 3 ай бұрын

Try using the other pin if your timing chain kit came with it. Is your car manual transmission or automatic?

@greg9323 6 ай бұрын

Thank you for the video it was very helpful in changing my timing chain. Question where can purchase a crankcase breather hose? Mine is cracked and the internet is not showing the correct hose.

@zevisgarage 6 ай бұрын

Here’s the part number 11157612996

@greg9323 6 ай бұрын

Thank you@@zevisgarage

@izzzzzz6 5 ай бұрын

What's the little chain behind the main one? Oil pump or something? Mine is super slack. Is that normal?

@zevisgarage 5 ай бұрын

Oil pump chain. Completely normal for it to have a bunch of slack

@silverlover5817 Ай бұрын

Thanks for the video. I'm about to purchase a 2013 N16 Cooper with only 20,000 Mileage on it (it has been sitting in the garage lots of times), so do you think the timing chain should be okay on it?

@zevisgarage Ай бұрын

Personally I’d probably replace it just because. I’m very extra like that. But in theory it should be okay. I’d recommend looking at the guides to see color and judge health

@williamnelson9336 3 ай бұрын

How do you reset Vanos Adaptations? Great video by the way.

@sleepydragonzarinthal3533 2 ай бұрын

I use my scan tool foxwell NT510 elite to reset adaptations

@rj7008 3 ай бұрын

Very helpful N16 video, Zevi. I was hoping you would show how you relieved tension on the accessory belt and that it didn't involve a special tool. If you remove the right headlight and raise the engine with the jack under the oil pan, can you access the 30mm tensioner bolt with a 30mm socket?

@zevisgarage 3 ай бұрын

Yes, but now on n16 and n18 cars I use a 30mm crows foot, I can remove tension from belt without lifting the car or removing any parts. I'll have a video on it soon

@rj7008 2 ай бұрын

@@zevisgarage Another quick question: Rather than using a socket & breaker bar to remove the crankshaft hub bolt, what are your thoughts on instead using high torque impact wrench (e.g., Milwaukee 2767) after locking the crankshaft and camshafts with the camshaft alignment timing tool?

@zevisgarage 2 ай бұрын

@@rj7008 definitely possible, it’s very high torque so you definitely need one of the big boy impacts to do it. I don’t have any strong enough ones to get it off

@rj7008 2 ай бұрын

@@zevisgarage Thanks again, Zevi. My Milwaukee 2767 is powerful and removed my Honda crank bolt in about 2 seconds. Maybe I'll give it a try on the Mini N16 crank bolt in late summer.

@rj7008 2 ай бұрын

@@zevisgarage Sorry for so many questions, Zevi. When you 180-degree torqued the crankshaft bolt, did you use a 1/2" or 3/4" breaker bar and what was the length of the breaker bar and extender pipe? Finally, can I safely assume that most videos don't show the entire procedure for torquing the Mini Cooper crankshaft bolt because it's like wrestling a bear. :)

@1ruffell Ай бұрын

What is a good brand or what cam lock set do you use?

@zevisgarage Ай бұрын

OEMtools Schwaben also makes a Kit, I have several kits

@PilotInProgress90 3 ай бұрын

When you say you had to 180 it, did you turn the cams individually? My flywheel locks with the cams 180 out. I cant get it to lock in the correct position, and the internet tells me the flywheel only has 1 hole for the locking pin. Car ran decent, is it possible its timing was so far off?

@zevisgarage 3 ай бұрын

Keep spinning it, it will line up

@PilotInProgress90 3 ай бұрын

@zevisgarage I've turned the engine over so many times trying to get the pin in when the cams have writing up and flat tops and sides. I'm just missing the hole?

@PilotInProgress90 3 ай бұрын

I just gave the engine 15 or 20 more turns. The flywheel pin 100% only goes in when the cams are 180 out. It went in several times very easily, but only in that cam position. All 4 cylinders are in line. If I lock the flywheel and cams in this position, and replace the chain, it should still be timed correctly since the crank and cams are not moving?

@zevisgarage 3 ай бұрын

@@PilotInProgress90 180° out as in text facing down and round side of cam lock spot is up?

@PilotInProgress90 3 ай бұрын

@zevisgarage yes. Just like you had them in the video when you took the chain off. As you were putting the cam lock in place you mentioned needing to "180" it because you had the writing facing down. My writing faces down, top of cam lock is rounded. If I orient the cams correctly, the flywheel pin does not go in.

@LisabethMiller 3 ай бұрын

and recommendations of a shop that can do this for me in Los Angeles?

@zevisgarage 3 ай бұрын

I do them sometimes, but if not probably Mini world or such can do it

@LisabethMiller 3 ай бұрын

What city are you located in? Would you be interested in doing it? The dealership wanted like 6k that's nuts! I guess for vanos? Makes no sense!! My car is so cute it would make a good model for you!

@zevisgarage 3 ай бұрын

@@LisabethMiller what year is yours? I’m in Los Angeles

@LisabethMiller 3 ай бұрын

2017 🥰

@LisabethMiller 3 ай бұрын

If anything I would love to get your opinion on what to do with it! Should I fix it? Sell it? I just don't know what to do! I'm in love with the color and it's so clean but is it worth it to fix it with 145k miles? It seems to drive nice, everything seems to work! It's a shame that Mini dealership quoted so high to repair!

@donnieboy123 4 ай бұрын

So cam locks weren’t needed ?

@zevisgarage 4 ай бұрын

Not for disassembly but to time the engine again yes they were needed

@jaydee1389 Ай бұрын

I need to do this for my car but i dont have the tools. so i have to take it to a shop. they want 2800 for the job. it only has 40k miles. the check engine light gave a code saying the guides need to be replaced. but not the chain. but i figure if the guides gotta go then the chain does too...

@zevisgarage Ай бұрын

What code? There isn’t a code that will say guides need to be replaced

@jaydee1389 Ай бұрын

@@zevisgarage you are right. There isn't a code. The check engine light is on. First it was the solenoids, then the O2 sensor. I changed them. Then I changed the gasket cover. I took it to AutoZone and it says the guides need to be changed. The same codes came back. For the O2 sensor and the solenoid. I have a cheap code reader. Autel brand that I got from Amazon.

@jaydee1389 Ай бұрын

It says 287D engine dme motor electronics. Dme vanos inlet: actuator movement. Status: not present. 2845 dme vanos exhaust actuator movement. Status not present I figured those codes are clear. But why are they there. Then it says 2A8B dme oxygen sensor before catalytic converter calibration line present. Idk what that one is. But maybe that's next to replace. AutoZone says replace the guides