mini cooper R56 turbo heat shield removal & forge blanket installation

Рет қаралды 8,275

Johnny Tan

Күн бұрын

Пікірлер: 28

@taffyboy1978 2 жыл бұрын

Great, but you missed half the screws out. What about the screws at the bottom by the radiator??

@codyrebelcb Жыл бұрын

And no mention of nut/bolt size either. Just movie music in the background.

@taffyboy1978 Жыл бұрын

@@codyrebelcb lucky enough my screws at the bottom were missing, so I installed the blanket and didn’t bother with the bottom screws. It was fine like that

@georgetudor1767 Жыл бұрын

And I m sorry ..the 2 screws from the bottom? Did they unscrew and screw by magic ?

@davidholder5471 Жыл бұрын

Nope missed the bolts underneath

@stephenboruk-mz2xf Жыл бұрын

How does the blanket attach underneath does it just took under or does it need to be bolted in as well

@JotakAlemao 2 жыл бұрын

What about the block and cat heat shields?

@linusprice Жыл бұрын

But how to remove the 2 bolts hidden under the turbo for the blanket because i have no clue how to losen them and how i can screw them back in.

@sassyrav Жыл бұрын

I have the N14 engine and yeah those bolts are tough to get to. I had to use an open end spanner and it took me a fair while. Very tricky to get off but its certainly doable. My hands are pretty cut up from the plastics surrounding those bolts.

@philipcoughlan7449 3 жыл бұрын

Great vid do you no were the boost pressure sensor is

@johnnytan4503 3 жыл бұрын

It's at or near the charge/boost pipe. U can see the image . Follow link . www.pelicanparts.com/techarticles/MINI_R56/87-FUEL-Turbocharged_Engine_Pressure_Sensor_Replacement/87-FUEL-Turbocharged_Engine_Pressure_Sensor_Replacement.htm

@johnnytan4503 3 жыл бұрын

Figure 10/11/12 (fr the link)

@philipcoughlan7449 3 жыл бұрын

I have the SD r56 diesal 16 is this the same engine dose the desal and petrol work on the same based

@johnnytan4503 3 жыл бұрын

Not sure wheather it is the same. Mine is petrol.

@jameshinged3002 2 жыл бұрын

do you have stock cataliytic downpipe? any issues with it??

@johnnytan4503 2 жыл бұрын

I changed to a catless downpipe a year ago, so far so gd.... except there is an error code occasionally appear that refers to mass airflow efficiency. No big deal though, I just refresh it with Torque apps. The forge blanket still look gd n works fine after a yr now..

@SassyOnline 2 жыл бұрын

What exactly is the point in this? What difference does it make over just keeping the stock heat shield??

@ruan800 2 жыл бұрын

kzfaq.info/get/bejne/fNh2mMR_rKrSf58.html&ab_channel=EngineeringExplained

@marcusrianfernandez 2 жыл бұрын

hows the race chip holding up?

@johnnytan4503 2 жыл бұрын

Still good atm.

@marcusrianfernandez 2 жыл бұрын

@@johnnytan4503 would you say it's worth it?

@johnnytan4503 2 жыл бұрын

@@marcusrianfernandez ya bro... it is worth the money spent. Love the extra boost :).

@gretre4560 3 жыл бұрын

Why didn't you show the bottom bolts

@johnnytan4503 3 жыл бұрын

The bolts is only at the top.

@gretre4560 3 жыл бұрын

@@johnnytan4503 oh ok. I have a 2010 mini s with the N14, maybe that's why. I had 6 total, three on top, 3 on bottom below the O2 sensor, or front depending how you look at it. Thanks for the video tho!

@Studio1311 3 жыл бұрын

It's probable that the 3 at the bottom were never put back after the older blanket was installed. Those 3 in the bottom are very hard to take out and even harder to put back in without taking apart the front assembly.

@gretre4560 3 жыл бұрын

@@Studio1311 i could see that. It definitely crossed my mind to give up on screwing those bolts back in. Hardest part of the entire install for sure. Thanks again for the video!

@kidjef Жыл бұрын

@@johnnytan4503 there are 6 bolts total, 3 at the top (the easy ones) , 3 at the bottom (the fml ones).