No video

MINI EXCAVATOR TIPS

  Рет қаралды 9,563

aguyandhismuttgarage

aguyandhismuttgarage

Күн бұрын

remember grease after each use and oil change every 80 hrs. or once a year after the first 20hrs. break in period. hydro oil should be changed every 200hrs or every 2 years. at a minimum.

Пікірлер: 14
@vdubluv222
@vdubluv222 3 ай бұрын
great video. thank you! i was due to buy something else from Milwaukee LOL.
@DAS-Videos
@DAS-Videos 4 ай бұрын
I would add that people may want to disconnect the two hoses for the swing bearing and then pump grease into the fittings until grease comes out of the disconnected hoses. I thought I was greasing mine thinking the hoses were already full but nope. I had to pump quite a lot of grease until it came out of the hoses.
@normhowes2975
@normhowes2975 4 ай бұрын
Great points on changing zerk fittings out. That was the 2nd thing I did as the 1st was 'attempting to grease mine. OK that was after I made a small hole in the ground lol
@aguyandhismuttgarage
@aguyandhismuttgarage 4 ай бұрын
I also made the rear panel into a door with some weld on Barrel hinges. It's much easier to gain access now.
@alexanderthevoice
@alexanderthevoice 4 ай бұрын
Idlers and rollers doesn't have grease port, they are sealed with oil. Actually they use engine oil in my ViO-55. Same as the final drives.
@DrSweetshaft
@DrSweetshaft 4 ай бұрын
I was wondering how to lube those, thanks
@PovertyPointCustoms
@PovertyPointCustoms Ай бұрын
They are about 2100lbs, most assume they are 1.5 tons or 3000lbs
@DrSweetshaft
@DrSweetshaft 4 ай бұрын
Grease every time? Sounds excessive.
@jayjames1657
@jayjames1657 3 ай бұрын
I have the same one you have This is the first video I have seen foe a miva va15 mini Right now i have a problem if where my hydraulic is not working it wont walk the boom and bucket moves very slow
@jgrohio
@jgrohio 11 күн бұрын
Grease fitting metric?
@dirtydish6642
@dirtydish6642 4 ай бұрын
Daaang! What does a unit like this cost these days?
@JLonz-hz8hi
@JLonz-hz8hi 4 ай бұрын
What Amsoil Hydraulic oil did you use? Did you notice a difference in the operation of the Machine? IE smoother controls.
@aguyandhismuttgarage
@aguyandhismuttgarage 4 ай бұрын
I used iso 46 and it operates the same it was smooth before the fluid change anyway.
@jayjames1657
@jayjames1657 3 ай бұрын
Mine did come with Briggs and Stratton engine
MINI EXCAVATOR TIPS PART 2
17:01
aguyandhismuttgarage
Рет қаралды 8 М.
800+ Hour Chinese Mini Excavator Review
7:49
NexGen Landscapes
Рет қаралды 14 М.
女孩妒忌小丑女? #小丑#shorts
00:34
好人小丑
Рет қаралды 56 МЛН
Magic trick 🪄😁
00:13
Andrey Grechka
Рет қаралды 45 МЛН
Chinese Mini Excavator Digging Stump and Leak !!!
14:46
What A World
Рет қаралды 6 М.
Stump Dig Number 1
12:23
SEMO-Dyer
Рет қаралды 10 М.
Cheap chinese excavator adding oil filter
18:04
You can do it Dave
Рет қаралды 6 М.
Electrical Overview On Chinese Mini Excavator QH12 FF12
19:28
86 Service
Рет қаралды 4,1 М.
Chinese Excavator Kymron ZX22 Broke down AGAIN! FIX
16:48
Beyond Machinery
Рет қаралды 5 М.
Mini Excavator QH12 Mods (Muffler & Drive Motor)
12:27
Papajunk
Рет қаралды 15 М.
Chinese Mini Excavator - 1 Year On
22:18
Homesteading Uncontained
Рет қаралды 1,1 МЛН
女孩妒忌小丑女? #小丑#shorts
00:34
好人小丑
Рет қаралды 56 МЛН