Mini Workbench With Quick Release Vise || Pikasäätö puristimella varustettu pieni työpenkki

Рет қаралды 113,288

4 жыл бұрын

Link to my channel: / @ospuupaja
!!! WATCH THE VIDEO !!!
NEW UPDATED MODEL FOR QUICK RELEASE SWIVEL LATCH DEVICE:
• Updated Latching Device
***************************************************************************************************** Mobile workbench with a quick release vise.
New idea for quick release vise mechanism.
Easy to carry and easy to attach to different surfaces (Table, Table Saw, Sawhorse, etc.) with a couple of clamps. Total table length 60 cm and width 36 cm, Jaw Opening 18 cm.
I used Finnish birch plywood as a material. In the future I’m going to use a similar mechanism when I make a vise for my workshop table.
*****************************************************************************************************
Uusi idea pikasäätöisestä ruuvipuristimesta.
Kätevä pieni työpenkki pikasäätö puristimella.
Helppo kiinnittää erilaisille tasoille (pöytään, sirkkelin päälle, työpukkeihin ym.) parilla puristimella.
Aion tehdä samalla mekanismilla puristimen myös minun kiinteään työpajan pöytääni.
Kätevä kuljettaa mukana, vaikka autossa. Materiaalina kotimainen koivuvaneri.
Leukaleveys 36 cm ja aukeama 18 cm.
Pöydän kokonaispituus 60 cm.

Пікірлер: 79

@oldpopmike 9 сағат бұрын

A bit unclear how the mechanism works. Thanks for the video. Well done.

@1705s 6 күн бұрын

👍👍👍 very nice! Ilike it very much THX for showing ! may be I find time to rebuilt this! Very niche 👌👌👌

@paulgriffin8566 3 жыл бұрын

What can I say. Swiss precision in a wood work bench. Amazing.

@MrMtrent5 10 ай бұрын

I've had the chance to use this table a couple of times now. It's fun to whip out in front of people:) I can see what people are talking about when they say the legs are delicate, but they're design to support a "mostly" vertical load, not be torqued from the side or pushed back into place. If you just let the table open or close on it's own and don't force anything, it works great kzfaq.infoUgkxyFZUPFEey-PuqsPMxqaykBhgA1LWxFHh Once it's set up, it's pretty solid. My only gripe would probably be related to the clamps provided. They're not the highest quality. They do the job, so no big deal, but they could be better. All in all, pretty cool gadget.

@JonasNeumann6 3 жыл бұрын

A very complicated mechanism but way safer and less friction than the others! Good job

@-100porfidollars 4 жыл бұрын

That is genius ! I am simply amazed by the engineering thought that went into this ! You sould sell this idea !

@paulor.trombini3078 2 жыл бұрын

mostre o sistema.interno de aperto ppr favor.

@kiwdwks 3 жыл бұрын

So awesome! The thought process is beyond me. Thanks for showing it!

@reytiosejo3012 2 жыл бұрын

Genius Idea and it turns to a reality that was very useful and works surely no slip unlike the other design of quick release bench vise,i will give you a perfect 10 .

@NikosDIY 4 жыл бұрын

Pure Genius! Amazing.

@zn6761 4 жыл бұрын

This is simply genius!

@mdshahjahan3789 3 жыл бұрын

Marvelous idea, superb!!!

@Heseblesens 3 жыл бұрын

A lot of engineering applied. Smooth operation! Plywood can't be expensive in Finland ;-)

@osmanerinc7316 2 жыл бұрын

Sharply idea. Nice 👍

@hermannkahlfus8394 3 жыл бұрын

Wahrlich ein Genie,ich bin unglaublich beeindruckt von der Arbeit,Respekt und höchste Anerkennung aus Deutschland

@OSPuupaja 3 жыл бұрын

Danke Vielmals!!

@Beverlys-Hillbilly 3 жыл бұрын

I love this! I'm gonna try something very similar using a wooden screw for the shaft.

@el-khanaziz658 5 ай бұрын

_Genial and clever. Thank u for sharing your experience._

@phanttom11 4 жыл бұрын

Todella hieno toimintaperiaate. Ja äärimmäisen hieno toteutus.

@kc-zq7ud 3 жыл бұрын

素晴らしい！感動しました！

@TonatiuhMellado 3 жыл бұрын

Una genialidad, gracias por compartir

@user-nk3hs2ct4j 27 күн бұрын

bravooooo👌🏽👍🏻👏🏽👏🏽👏🏽👏🏽👌🏻👍🏻😍👍🏻

@gabrielmariamarchi6221 3 жыл бұрын

Fantastica, veramente bravo!!!

@lesgoins5124 3 жыл бұрын

What a coincidence...was making the same thing just the other day… should have made a video of it… LOL Yep... agree... pure genius even Jay might be envious of...!

@KitoMarchetaria 3 жыл бұрын

Very good job !!!

@pafdaddy07 3 жыл бұрын

Very nice work. This is engineering :-)

@thekashif 3 жыл бұрын

Ingenious!

@Bob-More-Than-Enough-WC 3 жыл бұрын

Brilliant!!!!!

@stevenong6611 2 жыл бұрын

Very good idea,

@didierdesmet7064 Ай бұрын

Magnifique

@lvttvn9365 3 жыл бұрын

From Rio de Janeiro Brasil, thanks for your video great mini workbench.

@OSPuupaja 3 жыл бұрын

Thanks! Nice to hear that you liked the video.

@s7mogato 3 жыл бұрын

Simplemente, ingeniería pura.................excelente

@OSPuupaja 3 жыл бұрын

¡Gracias! 🎅🤶

@juancatani6124 3 жыл бұрын

Espectacular.Gran idea.Te felicito. No sabes lo que aprecio algo asi sencillo e ingenioso.Muy bueno .Sds desde Argentina

@OSPuupaja 3 жыл бұрын

Muchas gracias por tu comentario. 😊👍

@mili158 3 жыл бұрын

this is so smart!!!!

@norapetitdelavilleon6402 3 жыл бұрын

excellent!

@guyprolly 2 жыл бұрын

Very clever.

@WalterandFriends 3 жыл бұрын

SUPER!!!

@thejimmyjimmy3127 2 жыл бұрын

I like how it works. Seems to be nice and strong. Tip. When making the notches for the "spring clip" in the long release nut...put a bolt in the long nut and add another nut to lock it on the end then simply put the bolt thread end in your drill and start the drill while keeping the grinder on you mark. This will make a much neater grove. Not that it will be seen after its installed but everything made with love works better I find. Great build. Going to build one. Thnx for sharing

@OSPuupaja 2 жыл бұрын

Thank you for the comment. You are really right. I could have done that part a lot neater, using a drill and angle grinder. But this was only a test piece that then remained in use. My latest model for this part consists of two nuts with a spring in between.

@thejimmyjimmy3127 2 жыл бұрын

@@OSPuupaja would like to see the upgraded version. Love the creativity

@OSPuupaja 2 жыл бұрын

Ok, I'll see what I can do about it. Maybe I can share a few clarifying pictures.

@thejimmyjimmy3127 2 жыл бұрын

@@OSPuupaja Thnx a bunch. Really nice of you. PS. I thought the rest of the pieces on the vice was so nicely made and innovative so I was surprised by the method you chose to make the grove but I understand it was a test piece

@OSPuupaja 2 жыл бұрын

A video showing the structure and operating principle of the updated latch device can be found at the link below. kzfaq.info/get/bejne/m6iVaZxe07Kqmmw.html

@user-pw1df8sj3w Жыл бұрын

Epic!

@prnito 3 жыл бұрын

Congratulations

@diykoubou9229 3 жыл бұрын

すごいですね❕

@clausfriishansen2247 3 жыл бұрын

In the beginning a didn't have clue what was going on - then it dawned on me :) Very clever :) What's the "pitch" in the stacked sandwich plywood locking block?

@OSPuupaja 3 жыл бұрын

Thanks! I try to make the videos so, that the product is built step by step and only at the end of the video will the structure and function be revealed. The locking blocks are made of 9mm thick birch plywood pieces with a size of 87x87mm.

@poteb 3 жыл бұрын

Looks very interesting. To make a real product out of this would require it to be made out of steel, which in this case would be very expensive. If you can figure out a way to use less mass in the locking, then I think you could go further with this.

@OSPuupaja 3 жыл бұрын

Thank you for the comment! On the other hand, the mass gives more stability to the workbench. Weight 14 Kg, I think the weight of like this (mobile)workbench is very reasonable. This is for a wood workshop and is also a woodworking project, so plywood was a natural choice.

@clbro3085 3 жыл бұрын

I do like it if you made plans they would sell 👍👍👍

@robertohassenteufel1991 3 жыл бұрын

Einstein level...! Genius

@OSPuupaja 3 жыл бұрын

Thanks! 😀

@nasrullahmelayu5793 3 жыл бұрын

good

@bogas78 7 ай бұрын

Will you publish any plans for this ?

@user-sr5su4pu3t 2 жыл бұрын

Благодарствую 👍👍👍👍👍👍👍👍....!

@lesgoins5124 3 жыл бұрын

Maybe Incra should b making theirs out of wood...:-)

@aminoplis777 3 жыл бұрын

Great, inspiration!!!

@hierkonntemeinnamestehen2772 3 жыл бұрын

Hallo, das gefällt mir sehr gut. Gibt es dafür Pläne?

@OSPuupaja 3 жыл бұрын

Hallo, danke für den Kommentar. Leider ist der Plan noch nicht fertig. Ich versuche, Zeit zu finden, um es zu vervollständigen.

@joh.h.7855 2 жыл бұрын

Hallo aus Deutschland, schöne kleine Werkbank die Sie da gebaut haben. Gibt es einen Bauplan, damit ich das Teil nachbauen kann? LG Joh.

@OSPuupaja 2 жыл бұрын

Danke für die Grüße! Maßzeichnungen sind fast fertig zur Veröffentlichung. Weitere Informationen folgen später im Frühjahr.

@joh.h.7855 2 жыл бұрын

@@OSPuupaja Vielen Dank, da kann ich warten. Schön das es klappt! LG Joh.

@humbertodearaujo3359 3 жыл бұрын

👏👏👏👏👏👏👏

@SaMyVaiS 4 жыл бұрын

Erittäin nerokas idea ja varmasti ihan tarpeeksi vahva puutöihin. Toteutus oli ensiluokkaista.

@skincade1 3 жыл бұрын

Would love to purchase plans so as not to have to guess at dimensions

@OSPuupaja 3 жыл бұрын

Thank you for your interest. I’m going to offer plans for a few products this spring, when I might have time to focus on a wood workshop hobby. I also have a couple of videos of a simple woodwork product coming out. I’ll get them ready for release later this month.

@lint2023 4 жыл бұрын

Very nice project. You have a lot to offer. But, all those zooming transitions don't work. I won't last long with them.

@OSPuupaja 4 жыл бұрын

Thanks a lot for your comment and feedback. I’m trying different ways to make transitions. I think some of them work well, while some are not quite so successful transitions and the same thing with background music ....

@paulor.trombini3078 2 жыл бұрын

show show👏👏👏👏👏

@fa256b7 2 жыл бұрын

👍👍👍👍

@jean-claudefrancois1839 3 жыл бұрын

SUPER BOULOT .......!!!!!!!

@OSPuupaja 3 жыл бұрын

Merci!

@3rdworldgamer495 2 жыл бұрын

14:14 What is the function of the snap ring?

@OSPuupaja 2 жыл бұрын

The locking ring holds the spring in place. The spring presses a small round piece of metal (14:06) against the threaded rod. This increases the friction between the threaded rod and the locking device. This friction ensures that the metal latch moves in and out of the locking cavity as the threaded rod is rotated. At the same time, it ensures that the latch does not spin automatically into the lock cavity when the clamping jaw is pulled open. I have made an updated version of the lock device. You can watch the video from the link below: kzfaq.info/get/bejne/m6iVaZxe07Kqmmw.html

@3rdworldgamer495 2 жыл бұрын

@@OSPuupaja Thanks and great vids!