Minitruck | IRS | independent rear suspension swap

No video

Minitruck | IRS | independent rear suspension swap | Part 1

Рет қаралды 15,416

Күн бұрын

Just shedding a little light on swapping an IRS into a minitruck. Ask any questions you have in the comments.
Truck: 95 Nissan Hardbody
IRS: S14 240sx

Пікірлер: 36

@LooseFab Жыл бұрын

I just started building a 620 over on my channel. Just picked up an s13 subframe that i intend to put into the truck but I definitely have not taken on anything of this caliber. this was some great info, thank you!

@Otto_Factory Жыл бұрын

Yeah, glad people can use it! Measure 100 times lol

@Inner_Sanctum 5 жыл бұрын

Looking good man! I’m a little further behind than you are, but getting there. We have to link up one day when they are finished. Keep up the good work.

@TheBiteSize 4 жыл бұрын

Definitely appreciate everything about this video and series.

@TheBiteSize 4 жыл бұрын

@autofactory also a link for the tram gauge?

@Otto_Factory 4 жыл бұрын

www.amazon.com/Mo-Clamp-MOC7000-Gauge-Universal-Storage/dp/B00063X1NO

@TheBiteSize 4 жыл бұрын

You da man! @ottofactory

@SavageMotoring 5 жыл бұрын

Awesome videos man. I love how thorough you are explaining everything. Keep making videos on the Hardbody man, super cool project! I have a 2jz in my garage and an e46 subframe I've debated throwing in mine.

@Otto_Factory 5 жыл бұрын

Yeah thanks man! I just wish I could make them faster.

@pvalley3907 3 жыл бұрын

@@Otto_Factory so I can still use the rx7 vert sub

@pvalley3907 3 жыл бұрын

@@Otto_Factory i got a 74 toyota will this still help

@Murphyslawfarm 3 жыл бұрын

Great video mate

@barnstormerr 3 жыл бұрын

Your videos are top quality dude. I have a S14 and recently bought a Datsun 620 with the goals to do a S chassis IRS setup, so this helps out a TON. What made you decide to not stick with stock rear section of the frame? It looks like it would have worked out pretty good just making brackets for the subframe mounts. Was is mostly to mount the fuel cell? That being said, the setup you went with is fantastic, more curious than anything.

@Otto_Factory 3 жыл бұрын

Lol I ask myself the same question all the time. Pretty much just because I wanted to try making the notched out frame rails to see how they would work. If you get to a few of my D21JZ videos you'll see I had the engine and trans all setup and was going to run the truck front suspension to get her going.....nope let's cut the whole front end off and use something else 😂😕😑🤦

@R0yL33 4 жыл бұрын

Wow that's low for ride-height. maybe its just the camera angle. How did you decide on ride height? Mock it up with all the sheet metal + wheels , or just put the cab x inches off the ground? How did you figure out the vertical position to weld the rear susp to the frame? Just jack rear up so the control arms are more or less parallel to the floor ... or pumpkin x inches off the ground ? Ambitious build!

@Otto_Factory 4 жыл бұрын

4" is the bottom of the frame to the ground. That's actually not too bad. Since the cab is going to be body dropped the rockers will be level with the bottom of the frame. As for the suspension, I setup the rear subframe to where it would sit pretty close to the factory ride height. That way I don't have to play with trying to correct suspension geometry because the arms are so jacked because the cars too low.

@H00K-KING 3 жыл бұрын

@@Otto_Factory you set the rear subframe at the 240 factory ride height or the truck factory ride height?

@Otto_Factory 3 жыл бұрын

@@H00K-KING the 240 ride height, but it can be shimmed down if need be.

@H00K-KING 3 жыл бұрын

@@Otto_Factory do you happen to know what that is? I’m trying to figure out how to mount s13 front and rear suspension in my ‘74 duster. I’ve already built a tube front end and back half so now it’s just a matter of mounting them.

@H00K-KING 3 жыл бұрын

@@Otto_Factory correct me if I’m wrong, but I would want to have both subframes completely level and at the 240 ride height right?

@pvalley3907 3 жыл бұрын

I got a 74 toyota can I still use this video as a guide

@Otto_Factory 3 жыл бұрын

Sure, but also do a little research. I'm sure someone out there has swapped an IRS into a 74 yota

@pvalley3907 3 жыл бұрын

@@Otto_Factory I've been looking for a year now I seen someone have bags but his truck is a 77 or 78

@lexaniwheel 5 жыл бұрын

What’s the track width of the 240sx rear suspension?

@Otto_Factory 5 жыл бұрын

58"

@lexaniwheel 5 жыл бұрын

Otto Factory is that measuring from the wheel mounting surface or outside of tire or center of tire

@Otto_Factory 5 жыл бұрын

@@lexaniwheel I believe that's the mounting surface. Wiki says the factory track width is 68" I'll get my tape out when I get home and see what mine is.

@Otto_Factory 5 жыл бұрын

@@lexaniwheel with the 17x10s (I think the offset is around +20) the outside to outside on the rear is 70"

@erichill5208 4 жыл бұрын

Great project. But before doing such a project. One should know the proper terminology. Front to rear is wheel base. Side to side is wheel TRACK WIDTH.