Great video. Small suggestion, the arrow points to somewhere when u r showing something. Pls correct it. And thanks a lot for the explanation.

Awesome vid but man that mouse cursor was annoying when it doesnt point at what your clicking and talking about

Thank you very much for your lesson. i am learning a lot from you. From: South Korea

It is a great series of explaining MP.

Great video!

You make good videos..thanks

will the use for an autonomous rover be very different to an autonomous plane? Is there a whole different program version for that? Thanks for all your help :)

Enjoyed the entire series... I'm wanting to direct some guys to them because I don't have the time to keep repeating what you already covered. The only negative is the displayed mouse cursor is quite frustrating to see where you are actually clicking. I thought the narration and content were quite excellent, however. Are the any remakes or further MP tutorials in the works? Thanks, Mark

hlo...this is just great videos series....i m just a beginner on quadcopter...i want to build autonomous quadcopter..can u please help me with that....just want to know what are hardware things you used for making this and software

hi, can i use mission planner on something which is not mentioned in the program ,like a paraglider or anything can be autonomous ?

I’m also using Li Ion batteries with Mission planner/Pixhawk airplane, and have been getting a new type of warning recently on the mission planner HUD in red. : BAD BATTERY Wondering if you had seen this too, and why? Seems there is an internal resistance monitor in arduplane set for Lipos, and it’s detecting too high internal resistance. (Normal of course for a Li Ion battery) Using 4S4P Li Ion NCR18650GA cells, and only pulling 23 amps. Cells rated for 10a each, so 40 amps total. I get the warning about 2/3 through the flight, after about 78 minutes, when going to a high power setting. Any way to select battery cell type, etc? Or to shut off the false alarm in Mission Planner? It stays until reboot. Happing with new cells and several new batteries, so I’m well sure that it’s not a real problem.. also batteries are giving 90+% of their rated capacity, so they are genuine. Just wondering if any one had seen the same thing?

I went through wizard and now the motors only run about half throttle on full will not lift off.Any thing that may have not been checked . ? the motor test on mission planner does not work with the Quantum Nova.

hi . i have apm 2.8 and i fly mini quads typically but before i head out to the field i was just wondering what i should do if i have a catastrophic failure ? lol . i assume i would head to the actions tab and if all else fails disarm it before it disappears.

Great video, nicely detailed and explained. I´ve seen the whole serie and it really helps. I have just one doubt, may you tell us what the "AZ" parameter is for? I had no luck trying to guess it. Thanks!

Im looking to get into this field for security purposes is there any settings to launch the drone at specific time intervals or say every couple hours?

how to install ? the execution file stops each time announces missing files.

Hello. could you kindly tell me if there is a way to adjust dead band like there is in betaflight. I've been discouraged from using my APM because of drifting and I know it could be corrected but no matter how much research I do I can't find a way to set dead band in mission planner

Hey, we use mission planner for our hydrone boat. We were working right next to a high security air field. Every time we tried to run a mission it would disarm our auto nav box. Have you heard of anything like this. Thanks

when you create a mission, the pc you bring with you must have internet connected or can it be off lne?

I have tried for the last hour trying to calibrated the compass through mission planner on my new Quantum Nova Pro and have been totally unsuccessful....I have watched several videos and point the axis north and rotate as instructed and it continues to give me a failed message....Help Please.

Hello... Great Video!! Havent flown a Quad yet.. just researching.. I love the idea of using a quad or fixed wing for various types of inspections we need to do regularly.. I have a question about how Mission Planner communicates with with the Drone during flight to do such things as adjust or change waypoints, RTL, etc? What type of comm link is Mission Planner working with?

buenas, no me sale es icono verde con letra H, a que se debe? gracias

Mouse pointer was not following what you were explaining. Found it a bit difficult to understand

You said you are using mission planner. And a specific version. What I don't quite get is what is the hardware that works with mission planner? Is it a Naze32? I doubt:-) NAZA? Dragonlink UHF? ImmersionRC UHF. There's so many receivers and FC boards I want to setup like this and doing lots of research. Also. Is there a way to get a small map view into FPV? One last question :-)... Is there a mobile app that's a little simpler for when you're AT the field and want to make on the fly changes to waypoints?Thanks!!!!

When I open Mission Planner I do not get the Simulation or Terminal screen icons in the upper left corner, only the Help screen icon. I'm just learning this. Any thoughts?

hey, how to setup radio to be able to use?

Very Good Video. Which Mission Planner Program are you using? Thanks

Are there any alternatives? I'm using Ardupilot in a plane, but I'm really dissatisfied with Mission Planner. It might be some of the slowest software I've ever used

good job on placing your cursor where we think it is haha

What API is using in Mission planner ?

at each point we need to hold the drone for 10 sec , how to do it please tell me

Curious...a speed is never set for the legs of the flight plan?

which Mission Planner version and type is this?

Do you have a link to download this software?

Isn´t HUD. The correct name is PFD or Primary Flight Display

Your cursor arrow did not follow your points of topic in this video.

video sound is very low

fix your cursor mate