my prop bearing collapsed and I used this video to replace it. Thanks for making the video guys!

Vraiment excellente vidéo, dommage que vous manquiez d'outillage. Vous m'avez fait mal au coeur à force de taper avec le marteau sur des croisillons tout neufs. L'étau fait bien l'affaire comme une presse hydraulique. Je donne 8/10 pour cette vidéo parceque le procédé du démontage et remontage est entièrement filmé. Ça aide pour les novices qui veulent faire le travail mais ne savent pas comment faire.

Nelsinho takezara , isso é igual uma peixada tu só come o peixe as espinhas joga fora . Observei também o uso incorreto de ferramentas mas, o que eu queria aprender eles conseguiram me ensinar e estão de parabéns.

This video helped me alot. Thanks guys keep it up

Parabéns pelo ótimo trabalho que vocês fazem, detalhe por detalhe. Já aqui no Brasil fazem de qualquer jeito.

Muito bom vim olhar onde solta o grampo da cruzeta e aprendi💪,estou trocando o rolamento 👍

Parabéns, gostei muito da aula!

Nice one great video was worried for you brothers when I say the knife 🔪 but you got it done and now I have the information I will too

Thanks heaps gentleman 🙏 Nice work 💪🍻

Would this center bearing failure cause metallic vibration as soon as 4th and 5th are engaged then stop when accelerating?

Nice work guys

Ďakujem za video teraz viem že je vhodné vymeniť s ložiskom aj kardanový kríž

Yes Sir.how we do it in the Land of Oz also ,, Golf Wagen..Good vid..:)

very good video =)

pozrel som si video a uz ma presla chut robit to.lozisko sice nehuci,ale je roztrhana guma a tak ma kardan velku volu.tazka praca😞,ale video poucne👍

excellent job I'm changing my 4wd Solenoid as well as doing this job myself... F the mechanics who would prob charge me $500+ - can do this for less than £100 including vacuum solenoid

stellar

Muito bom vidio aprendi muito e já vou fazer na minha obrigado.a equipe está de parabéns.

Where did you get that piece? I have a 2000 Mitsubishi Montero sport and need to change that piece

Thanks fellas You should invest in some brass drifts and or brass hammers

Muito boa as informações ao valeu muito

just replaced center bearing and 2 uni joints cost of parts 1100 thai bht = 36usd job took not too long

Bom dia no 🚖 táxi João pessoa PB 🌵🇧🇷

Bom trabalho

Parabéns gostei

Esa es la posición del rodamiento .????

quero saber o preço do Cardan da Triton L 200 2012

Ola buenas tardes dónde puedo conseguir el soporte dé la caja

creo que puso el rodamiento al reves , no le va a durar mucho , me pasó igual ,lo compré de nuevo y eso fue la falla , la cuna va hacia abajo , no se que digan los demas

Any ideas how to fix a 4WD status bulb that has gone dead? Not flashing, just doesn’t illuminate the parts to show the wheels. It DOES show the box when that’s engaged, but just not the wheels.

Muy pequeño ese martillo

Ja som teraz menil to stredové ložisko a tiež sa mi tak tažšie krútilo ako vám, keď ste ho tam nalisovali. Išiel som sa previesť, asi 20 km a sa zahrialo. Asi do neho dali veľa vazelíny, potrebovalo si asi sadnúť, neviem. uvidim, či sa to bude aj nadalej hriať. Ložisko je z japanparst.

you need to tap the bearing into position not use the spindle nut to press it on thats why it didnt spin properly

great job what is the cost of the joint and the center bearing ?

hm center bearing l200

Es más fácil usar el sargento para cruces

Não e fácil gravar e fazer por isso vai meu leick

you went in dry no lube wtf I hope you did not rip that bushing

I hate how in all these videos...the guys grip the soft part of the propeller shaft in the vice. It can be dented

Нельзя кардан в тиски зажимать

mau uso das ferramentas, acabam c tudo, kkkkkkkk

quero saber o preço do Cardan da Triton L 200 2012