MK7 GTI Engine Rebuild Pt.3 - Timing Chains and Oil Pans

No video

MK7 GTI Engine Rebuild Pt.3 - Timing Chains and Oil Pans

Рет қаралды 31,259

Жыл бұрын

We're rebuilding the actual best deal ever mk7. It's a 2015 Volkswagen GTI with leather interior and a DSG. I think this is the first gen 3 TSI engine build series, so follow along with us. We install upper and lower oil pans, the oil pump, timing chains and timing covers in this video.
Check us out on Facebook
/ weissworxaudimotive
#volkswagen #gti #tsi #mk8 #mk7 #mk6 #jetta
#ea888 #gli #jetta #golf #vw #audi #a3 #tt #auditt
All music is by Under Earth from the EpidemicSound app
share.epidemic...

Пікірлер: 28

@yabbadabba3994 Жыл бұрын

You guys are rollin! First start right around the corner!

@Weissworx Жыл бұрын

Hopefully Friday. Still need a couple of odds and ends to get it all buttoned up.

@victorserrano8167 7 ай бұрын

Muy bueno Master y de gran ayuda,pregunta en un motor 1.8tsi,el torque de bancada y bielas cuánto lleva,gracias

@Weissworx 7 ай бұрын

Connecting rod torque. Is 45nm plus 90 degrees

@victorserrano8167 7 ай бұрын

@@Weissworx gracias Master..

@pescatudo Жыл бұрын

top parabéns

@Britcherbrianjr Жыл бұрын

If I’m going to take advice from someone about a vw, it’s going to be someone with a vw tattoo

@davidut55 8 ай бұрын

When i honed, like you, the cylinders on my mk2 jetta, old rings had 0.4-0.5mm gap, original engine with 200k km. After some km maybe 1000km, disassembled again, and the rings were over 0.6mm gap. So my honing did worse, the finish wore down the rings in very few km. I am curious how much oil does it burn after this repair.

@Weissworx 8 ай бұрын

We have put almost 20k on the mk7 since the rebuild, oil consumption is around half a qt between oil changes. Well within tolerance. Sold the car to our buddy 4 months ago. It is now his daily and hasn't had a issue. Although after others advice. The last few motors we have built. We slowed the drill down and slowed the strokes, so the cross hatch angle is more with in spec.

@timz9406 Жыл бұрын

Hey. Nice build. I am trying to fix one of these. The problem is it was picked up by a forklift before and the forks have broken the oil pan and probably damaged the oil pump. I tried to measure oil pressure and I am getting around 5 psi which is very low compared to ~20 psi. The oil pump looks good and I am not noticing any scratches or broken parts. I also noticed there is small piece of metal that looks like it was broken, but it is behind the oil pump which makes no sense. Do you have any suggestions or reasons why I might of got it broken or if the bottom block skirt can me bend or damaged?

@Weissworx Жыл бұрын

Hey Tim, how long was the motor sitting before you got it?

@timz9406 Жыл бұрын

@@Weissworx Not sure how long but at least two months I think. However, I probably did find the problem why I am getting low oil pressure. The oil filter housing adapter was broken when the filter was changed and I have already ordered it and will be testing it in a bit. However, a small piece of metal that was missing behind the oil pump is still a mystery to me because it is inside the block, there is nothing that is touching it, and there was no signs of broken metal in the oil pan or anywhere near

@Sleepymk6 Жыл бұрын

My engine block has a hole as well as the upper oil pan , do you guys recommend I just get another engine or is it cheaper to rebuild it ?

@Weissworx Жыл бұрын

In your situation I would suggest find another motor.

@timz9406 Жыл бұрын

2:45 the piece of metal is missing right under the number 14 which is right on top of the oil pump

@Weissworx Жыл бұрын

Good Evening Tim, Can you send A picture to our email? Weissworx@gmail.com lets get you squared away!

@timz9406 Жыл бұрын

@@Weissworx yeah. I’ll send you some pictures tomorrow. I also think that due to the low oil pressure the oil filter housing adapter creates, the head-cams run a little bit roughly so I try to run the car as minimal as possible.

@Sebas0889 4 ай бұрын

It is possible to share the VW manual. possibly via email or a link, thank you very much in advance

@Weissworx 4 ай бұрын

Shoot us a email weissworx@gmail.com

@Sebas0889 4 ай бұрын

@@Weissworxwill do, thanks

@psiturbo Жыл бұрын

what happened with the follow up videos of this MK7 rebuild?

@Weissworx Жыл бұрын

Thanks for the reply. What follow up are you referring to? It was just a rebuild series

@psiturbo Жыл бұрын

@@Weissworx back in the engine, etc, prime, first crank, any gremlins from the build, final thoughts.... and so on

@Weissworx Жыл бұрын

@@psiturbo no problem give me a couple days and I can work on that we have some footage of first start

@lamerankala8432 10 ай бұрын

Hey.... I am mechanic from Botswana, can you please share with me all VW Engine repair manual you have "especially torque sepcs'' via EMAIL

@Weissworx 9 ай бұрын

Please email me at weissworx@gmail.com

@danwedderburn5550 Жыл бұрын

I would of really like to of listened what you guys had to say, as im just about to attempt a strip & rebuild of one of these. Sadly that stupid music you played prevented me from doing so, so i switched off.

@Weissworx Жыл бұрын

Thanks for your input. We still have a lot of room for improvement on vlogging If you have any questions. Email us. Weissworx@gmail.com