Thank you! The more options the better :)

Thanks! As designed :)

Thank you Frederick!

Thanks, almost could be a oven.

Excellent...

@@gorillaxrich Thank you!

Thank you Larsen

Thank you, unfortunately there is no space for a 3,5'' drive in between the motherboard and PSU. There is only 84mm of space in between those and the drive is wider.

Thank you Ellie!

Thank you 🙏

Thank you!

Thank you :)

Thank you Sk4tt! I spend way to many hours editing this.

Thank you Wim!

Thank you 🙏

Thank you Gijs!

I would love to see it, you don't have to so extreme as I did here. Start of small and do what you enjoy!

@@TerHorstCustoms Yes I would love to make or have something like this. I have the case but could not get the bottom rad in.

@@user-od3cb5bd8k The custom parts for this will become available as DIY for people who would like to do the same :)

Dankjewel! More soon™️

Thank you 🙏

Thank you!

Thank you and yes this also works for the window version if this case.

@@TerHorstCustoms Any chance you'll sell it... or the previous one? 😁

@@Garrett1974 Yes, I'm currently working on a small batch of Diy kits for people who would like to recreate the build on there own. If you would like more info send me a email at terhorstcustoms@gmail.com

@@TerHorstCustoms no I mean selling the builds... 😅

@@Garrett1974 Oh, no I do not current sell full systems.

Thank you!

Ik ga het proberen :)

Thanks

Thank you very much!

Thank you!

Thank you and yes, 30mm thick radiators

That is called a sandwich layout, due to the riser cable the motherboard needs no be inverted.

Thank you!

Don't be discouraged by hardware that ages, still very powerful these days.

I do not share the files, I'm working on getting some kits made for people.

Thank you, there is currently a new batch of kits in the works, the parts need to go to powdercoating to get finished. The kit was not designed around typical aircooled GPU's meaning support is very limited on those. For example a reference 6900xt from AMD does fit but it's limit on thickness and most current gen GPU's are bigger. The kit has room for a pump res combo cpu block.

Unfortunately not, as that space was used for the hardware.

I think the ratio is kinda off now.

You can see all the custom panels in the short before the case is out back together and yes a kit will be made available for people to install in there own case. Installing the fittings on the blocks is easy and can not be done before mounting the midframe or else it just doesn't fit in. Fittings in the rads can be installed while the midframe is removed and also fairly easy to do. Tubes can only be installed once the midframe is in the case.

Awesome, I am definitely interested!

@@sparkplugbarrens if you would more direct updates, you can send a email at terhorstcustoms@gmail.com

Boards can't be taller then regular itx (17cm) but can be longer like this board for example (www.anandtech.com/show/16277/asrock-rack-deep-mini-itx-romed4id-2t) This would cover over the cutout for the rubber gromet that is used to route the 24 pin power cable.

@@TerHorstCustoms - I see what your saying - In the custom world, I guess you could move the hole with the gromet. Would that get in the way of anything else on the back side?

@@lhbbq Correct, then you just move it since there is currently roughy 75mm/ 3 inches between the edge of the ITX bied and the PSU Cover. Only thing that I currently can think of is that the bend with the 24pin could be harder due to the cable maybe lining up with the GPU power cable front the other side.

@@TerHorstCustoms You are correct. Have you done any work on an I400? Even if you have not posted. I sent you an email. Can you share some pics?

@@lhbbq I have not done any work with a i400. What pictures would you like to see exactly? You can send a email at terhorstcustoms@gmail.com

Yes, its released. If you would like more info send a email at terhorstcustoms@gmail.com

Unfortunately not, the top it hits the riser/ ac cable in the PSU and in the bottom it would hit the fittings out of the FLT120 on the bottom.

@@TerHorstCustoms appreciate the info!

These are the temps after 45 mins of Aida64 Extreme stresstest in a 25c room: ibb.co/VT9trvm

The custom kit made out of the following new parts that can be installed original i100 Pro frame/ case. (Parts are shown at 1:01 in the video) 1x Rear IO panel. 1x Rear IO plate. 1x Front plate. 1x Motherboard midplate. 1x GPU midplate. 1x GPU support. 3x GPU cable cut out cover. 1x Pump/Reservoir combo bracket. 1x PSU mounting bracket. 1x PSU cover / dual 2,5'' drive mount. 1x Top cable shroud. 1x Bottom cable shroud. Includes following extra parts for user to be able to install the kit: 1x Drill guide for front plate. (Made out 1,5mm thick steel, powercoated and mounts to original case holes and stock screws) 1x Drill guide for bottom radiator mounting. (Made out 1,5mm thick steel, powercoated and mounts to original case holes and stock screws) 2x Metal drill size 2,5mm (To drill pilot holes with use of the drill guides) 2x Metal drill size 4,5mm (Final hole size to be able to mount front plate and most common radiator screws - M3, UNC6-32 and M4) 1x Countersunk bit 6,3mm (To clean up 4,5mm holes) 1x Instructions and Lengths needed for custom cables if you would like to go that route. Important note on what is needed but not included: - The kit does not work with the stock riser cable. -> For this I use the Link UP Gen 4 Riser PN: PCIE4EXT11SR-025 (Right angle 25cm long) - A EPS extension cable -> Total EPS power cable lenght needed = 700mm. Most stock SFX / SFX-L EPS cables are 400mm long.

@@TerHorstCustoms ahh... so it means that if i want to make an exact same one, i might not be able to? do you have a video on how to make them? or where it can be purchased from?

@@gn1w correct, I'm currently getting a batch of kits made for people, then they can remake it. If your interested you can send me a email at terhorstcustoms@gmail.com for more information

These are still the temps after 45 mins of Aida64 Extreme stresstest in a 25c room: ibb.co/VT9trvm

Thank you, glad your back

This one is 268mm from the op of my head but the GPU compatibility is as follows: 5.Max GPU height is 155mm and max length support; 5.1 265mm to 285mm with a FLT120 D5 or DDC. 5.2 325mm with a FLT80 DDC - Side port closed with stock plugs 5.3 405mm with a EK Velocity² DDC 4.2 PWM CPU/Res/Pump combo block.

@@TerHorstCustoms perfect! Thanks so much for the response. I already have a FLT80 but I also have the Barrow CPU Pump/Res Block! I’m 1000% ordering this case. Guess the NR200 will become my travel rig case or I’ll strip the paint & repaint it pink for my daughters build.

​@@YoloVib3sIt's a great case. I'm building in it now. You'll need to do mods (as shown in this video) to get 2x360s to fit. But in the horizontal GPU non sandwich layout you can do 2x360s with the bottom being an XSPC TX and 15mm or thinner fans.

@@paskowitz nah I’m shoving 6 P28’s in there

@@YoloVib3s that sounds like a fun build for your daughter as well.

The case with mods and custom loop parta is roughly 1,8k euro. So this with all parts at msrp would be 3,5k I guess.

Yes a 4090 will fit and that combo with a 7800x3d will be more then capable to be cooled.

I made the following new custom sheet metal panels: 1x Rear IO panel. 1x Rear IO plate. 1x Front plate. 1x Motherboard midplate. 1x GPU midplate. 1x GPU support. 3x GPU cable cut out cover. 1x Pump/Reservoir combo bracket. 1x PSU mounting bracket. 1x PSU cover / dual 2,5'' drive mount. 1x Top cable shroud. 1x Bottom cable shroud. Unfortunately I don't have a printable solution but I have made a small batch of panels. However I recently saw a printable option on Reddit that might be interesting for you.

@@TerHorstCustoms Hey would you Share the Proces how you done them?

@@ferhatkarakurt2720 you mean the design or how I made them?

@@TerHorstCustoms all the meassure from the Customer Panels you made

Unfortunately, those will not be shared as I have made a small batch of them to be sold in DIY kits for people who would like to get the same layout in their case.

Yes, I do and email would be easiest.

Correct and the case is not made bigger for that this mod then original.

Voor deze build niet, dit was met geventileerde panelen.

@@TerHorstCustoms Ik looking to build a new case and I'm thinking I might go for the i100. Did you see any other cases that have the potential to fit 2 360 radiators? Oh and does this case support a D5 pump in this config?

@@fissavids8767 it all depends on how much you want the modify the case. With these mods the builds used a D5 flt120.

@@TerHorstCustoms does your modkit support active backplates for gpu's?

@@fissavids8767 The EK ones, yes. Other brands I can double check for you if you would like that.

It is Corsair Hydro X Series XT Hardline 14mm Tubing - Satin Black

@@TerHorstCustoms thanks

Thanks!

Send us a email at terhorstcustoms@gmail.com and I can forward all I information.

@@TerHorstCustoms why you are not disclosing this information here in public?

@@borantube I can that is no problem but I want to make the potential buyer gets all info as well (what is included and what not)

Thank you, maybe I should but never really thought about that.

Keep working towards your goals and you will reach them!

thanks for the motivation bro@@TerHorstCustoms

We don't need RGB on everything but if you like you can turn it on :)

@@TerHorstCustoms that was a joke for people who understands. Nice response though 😄

@@user-ut4vl8bw2k We all know RGB = more FPS :P

How did you fit dual rad's???

@@gorillaxrich With the custom parts that I designed for it to make it fit. They are shown at 1:01 in the video.