Thank you for the video. I just got my new bender and it helps me getting started. Cheers, Chris
@ln3b5g13 жыл бұрын
Makes me want to go in the garage and work on my skills. Thanks for the new vid its been too long.
@Aurality11 жыл бұрын
Awesome. Thank you very much for sharing. I love being able to learn on here.
@danielboom269 жыл бұрын
good machine, guy greetings from Colombia
@douglasbattjes399110 жыл бұрын
Jason, Great video for all that never used one, I put a hyd. cylinder on mine. Like the info on the bender, all the little parts u never see anywhere else,like the spring back and slack issues. I use Teflon spray lube on the tubing, never have had a slide mark. Great Job. The W.T. on the tube is .120 WT stainless.?
@specialseventynine11 жыл бұрын
These bars are welded directly to coped mounting bungs, no knurling needed.
@dieselrotor7 жыл бұрын
Hello Jason. I see one of the two follower blocks (the trailing or lead block ?) is offset in pitch in parallel with the tube . How many degrees is the block pitched ? Also, if You would be so kind, does the height (top of die inner radius) of the die shoulders go past the center line of the tube or do they stop right at dead center of the tube ? PS - Subscribed Brother, like Your videos. Good,confident and fun presentation. Nice work !
@creativespark153910 жыл бұрын
Thanks for posting this video ...
@javcontre2224 жыл бұрын
Nice and useful video. Can you please tell me the part number of the die you are using?
@beamerboy325e11 жыл бұрын
Hey nice bars! But don't they need those tiny groves so they won't move when they are mounted to the bikes neck?
@alanr42634 жыл бұрын
Kewl video.I was hope ur measurements were all gonna be even lol. Is there cheap tubing u can get to practice with b-4 switching to expensive tubing?
@joeyk81010 жыл бұрын
Great video! dumb question, I'm looking to get one for the same purpose, would I go with the "pipe dies" or "round dies" ?
@ghislain631310 жыл бұрын
glad to have seen this video. good info. Can I ask if it's difficult to get that 22 degree you got before the second bend? how did you arrived to that number? thanks
@trip39808 жыл бұрын
My only opinion is when you weld I would make a small gap of 16th inch tack 4 sides grind them down then mig weld using stainless wire .
@superhahayeah10 жыл бұрын
Very nice work and how too.......whats the CLR on that die? About to order a bender and those look nice. I plan to do frames and bars with it and don't want such a tight bend that it looks like a plumbers 90 or such a loose CLR that close compounds on bottom tubes are impossible.
@martinp72568 жыл бұрын
+Ryan Baldwin Centre line radius
@superhahayeah8 жыл бұрын
+Martin Pender thanks for the reply but i was looking for the deminsions of his clr. i ended up getting the 3 inch die
@perezsira9 жыл бұрын
La percibo muy complicada, por supuesto es mi opinión. Saludos.
@SAXONWARLORD1000AD8 жыл бұрын
Is that your own handle on that machine
@Victorsadventures277411 жыл бұрын
Great video Thankyou
@valtermouradesouza10 жыл бұрын
Boa tarde amigo, como xama essa ferramenta
@rsz901827 жыл бұрын
nice work
@thatsmydollar65535 жыл бұрын
Did you tig, or mig these?
@jdug14328 жыл бұрын
Why couldnt you do the bars in one tube and just bend both sides?
@rsz901827 жыл бұрын
because the bike clamp would compromise the center. this makes it stronger when you clamp down.
@jbyrd7429 жыл бұрын
How much you sell thos for. I just bent my mini ape's on my bike.
Very nice work and how too.......whats the CLR on that die? About to order a bender and those look nice. I plan to do frames and bars with it and don't want such a tight bend that it looks like a plumbers 90 or such a loose CLR that close compounds on bottom tubes are impossible.