Model A Ford Top Front Trim Molding Bend and Install

Рет қаралды 1,238

3 ай бұрын

In this episode we will be discussing and showing how to bend the aluminum reproduction Top Front Molding Trim for the Model A Tudor Sedan.
• How to replace Model A...
Drip Rail Molding Video • How to bend and instal...
Smith and Jones Model A Parts, South Carolina www.snjparts.com/
Model A Medic Eric Weninger modelamedic.com/
Join MAFCA for many helpful resources with your model A at www.mafca.com/cart/index.php?...
Our online Store at pumpkintown-108720.square.site/
Our Website at pumpkintownprimitives.com/

Пікірлер: 18

@michaelrepetto669 3 ай бұрын

Very well done my friend 👏

@pumpkintown 3 ай бұрын

Thank you kindly and thanks for watching. Next video should be up in a week Lords willing

@captainldd 17 күн бұрын

really enjoyed your video. Thank you.

@pumpkintown 17 күн бұрын

Glad you enjoyed it!

@truthreigns7 3 ай бұрын

Great my brother in Christ

@pumpkintown 3 ай бұрын

Thank you dear brother! The Lord be magnified!

@pablo4015 3 ай бұрын

Muy bueno! Saludos desde Argentina

@pumpkintown 3 ай бұрын

Thank you brother!

@timothysotelo3868 3 ай бұрын

I am a bit nervous on this task. I will do mine this summer. Thanks for posting.

@pumpkintown 3 ай бұрын

I hope this will help take some of the nerves away. This is the video I wish I had before I started. I think annealing the aluminum is key and if I had to do it over again I would start nailing from the center and let the excess hang over on both sides. I think if you can watch my next video of the back when I post it then use that same technique for the front. Nailing and bending along the way I think

@brianmatthews9697 2 ай бұрын

It's not that hard. Let the roofing pre-stretch on the roof for a few days. Leave in the sun if you can. Take your time and think. You'll get it.

@craigroberts3982 3 ай бұрын

Excellent job. These cars are simple yet complex and a labor of love. I have a 30 coupe and the front trim is nailed straight through the trim. Not sure if that's correct but it is how mine is done. I wouldn't call it waterproof but I have no plans to find out.

@pumpkintown 3 ай бұрын

I wouldn’t either! lol! Thanks brother! Good to hear from you!

@magoo262 3 ай бұрын

Thank you for posting this! Are you planning to show the sides as well (I think they’re the rain gutters?)

@pumpkintown 3 ай бұрын

That was the previous video! Here is the link kzfaq.info/get/bejne/nddpl7hq05uuqY0.htmlsi=Bjm2GDu8tI8L_m65

@TrainDavid1744 3 ай бұрын

seam sealer works much better than the butyl rubber. I do the top before painting the car, and put paper down before the trim. Paint the car, and take the paper off and I suspect that's what the factory did too. BTW, get rid of that phillips screw on the rain gutter, a slotted oval screw is what was used.

@pumpkintown 3 ай бұрын

I have heard that Seam sealer works good as well. Sounds good to me. As for the screws, I am sure they were actually no screws used as they would have been snapped into the nail channel. Hardware store had no wood screws that were slotted. So these are temporary until I can get my hands of some slotted ones. Thanks for the comment. I agree!