Extra nice torch work. I also liked the quality of hardfacing.
@user-nyanmaru Жыл бұрын
素人目にも溶接箇所が綺麗ってわかる
@buroch11 ай бұрын
おすすめから来ました! この状態からの復元はプロ中のプロというか神の領域ですね!😮 溶接も上手い💯
@babcockcopper Жыл бұрын
Beautiful rebuild! Nice work
@industrealjapan Жыл бұрын
Now this is the world of art...
@samos_sainz Жыл бұрын
I want to give you extra points for the beautiful Yiruma music, and the sky and garden footage. I enjoyed the torch cutting, and the final assembly ended well. But, I would have liked more care on the joints: cleanness and joint preparation, full thickness welding (not leaving the joint's root hollow inside or poorly fused), and do not abuse of overlapping plates and welding mainly only on the perimeter (and I don't mean the hardening layers). I could be wrong, but I think that's what I've seen. I have to admit that I was expecting more from a Japanese... but at the same time, I have to admit that I enjoyed it. Cheers from a fellow welder, from Spain.
@gmendes1831 Жыл бұрын
Great heavy job!
@1212ImAnubis Жыл бұрын
That's good repair and hardfacing for bucket. I like it 👍
@industrealjapan Жыл бұрын
thanx bro. i like sushi & soba cause japanese ninja. please subscribe me thank you
@edwinhernandez9532 Жыл бұрын
Hermoso trabajo
@thomaspotthoff240 Жыл бұрын
eine hervorragende arbeit, respekt
@tomo1013101kentiku Жыл бұрын
すごい
@7tunedrotary Жыл бұрын
まるでなにかの化石かと思うくらいに丸まってしまっているな。 使い込むとここまで削れるのか。
@industrealjapan Жыл бұрын
私の友人はこれを鶏ガラと命名してました、有難う御座いました。
@okiedoke6373 Жыл бұрын
I don't know what he said in his closed caption if you see how all the lines of hard surfacing are straight that's because the hard surfacing down here in the United States is incorrect a piece of equipment that is going to be refurbished over and over you will see hard servicing lines going straight because it doesn't build up heat and form cracks
@ferdinandocappelletti674018 күн бұрын
Very professio nal work, my compliments
@jfro5867 Жыл бұрын
Nice job 👍
@shaneward6689 Жыл бұрын
Weld looks really cold, could have preheated for 20 minutes or until reach 450 degrees Fahrenheit , would help in case the welder does not have enough amps
@spencereagle1118 Жыл бұрын
It was like an old hippo being given new teeth.
@McNeillWelding Жыл бұрын
Dang lot of work and nice job. Everyone commenting about hardfacing but I’m wondering if the built up areas are the same flux core wire you were using for the other welding?
@industrealjapan Жыл бұрын
Thank you for your interest in the video. The wires used for surface hardfacing are the same as those used for other welding. However, there is a hard hardening wire around the three lower nails where the most force is applied.
@RiskyRight Жыл бұрын
I wish there is an english subtitle for the video. Ilove the video
i can make passable welds and i can operate heavy equipment my thoughts are they should have did this about 1500 hours ago
@user-cu4nt4bi2r Жыл бұрын
начало такое как будто какое то больное животное выхаживают а потом он стоит и тихо радуется за кадром грызлик ^^
@user-pk6jb8ik6r Жыл бұрын
ナイス👍😊
@industrealjapan Жыл бұрын
ありがとうございます。
@philliplopez8745 Жыл бұрын
BRAVO !
@jamesward5721 Жыл бұрын
Mig gun would be liquidising in your hands... effort.
@user-zs8hx2fx9b Жыл бұрын
素晴らしいお仕事です。暑くなってきますので、熱中症などにきをつけてください
@industrealjapan Жыл бұрын
有難うございます。早速本日熱中症になりかけましたので気を付けます。
@arilda9331 Жыл бұрын
Like from Norway
@industrealjapan Жыл бұрын
thanx.from edo japan ninja
@user-fb2sh2mn7r Жыл бұрын
ナイス盛りうますぎワロタ
@Ciaphas-Cain Жыл бұрын
во время сварочных работ нельзя заправлять брюки в сапоги и карманы на одежде сварщика должны быть плотно закрыты, иначе сварочные работы превратятся в сварочные танцы
@industrealjapan Жыл бұрын
Спасибо, что присмотрели. Я ниндзя из периода Эдо. Приходи ещё.
@Ciaphas-Cain Жыл бұрын
@@industrealjapan разве шиноби не больно, когда окалина в сапоги попадает? 😅у нас такое считается нарушением правил техники безопасности. и если где ни будь на предприятии инженер по технике безопасности заметит что сварщик так делает, наложит на него взыскание в виде денежного штрафа или лишения премии.
@makssvarshik Жыл бұрын
Всё хорошо , но почему у них такие маски ?
@vlcekhranice Жыл бұрын
pěkná práce
@RustyDockLight Жыл бұрын
That's extremely impressive. it takes steady hands to make welds like that.👍
Ну очень много лишней работы. Сразу обрезал под еорень и приваривай. Ну всё раано молодец.
@user-jx5ch3pd5e Жыл бұрын
これって修理補修した金額と中古で購入する金額でどっちが良いんだろ?
@industrealjapan Жыл бұрын
このマグネット小割は新品300万以上しますんでまだ直した方がまだ安いです。
@_MadFox Жыл бұрын
Интересная работа. Швы, которые положены сверху на сталь, применены для усиления, чтобы снизить истирание стали? Никогда не видел наплавку такого материала полуавтоматом, у нас чаще применяется штучный электрод. И небольшое пожелание - купите сварочную маску с вентиляцией, при вашей работе вдыхание этих газов очень вредно.
@alextrofimov6208 Жыл бұрын
Это старый ниндзя. Ему можно. Там дед пожилой ещё с эпохи Эдо.
@_MadFox Жыл бұрын
@@mrnobody1897 наплавку ведут тем, что у нас называют сормайтом, при помощи газовой сварки, а также применяя электрод Т-590 или Т-610 для ручной дуговой наплавки. А вот он делал наплавку полуавтоматической сваркой проволокой. Такой материал мне незнаком.
I wish the subtitles were translated into English. 🙏🏻
@industrealjapan Жыл бұрын
The process by which the God of Welding completely restores demolition attachments that have been worn to such an extent that they have never been seen before.
@rairai3517 Жыл бұрын
When was that equipment made and how many times has it been refurbed ???.......
@industrealjapan Жыл бұрын
It was still a new model. I think it's been repaired twice in the past. The wear and tear this time is not normal and it's the first time I've seen it. I was scared like a zombie...
@user-ux4mx9pi5l Жыл бұрын
ビフォーの方が東南アジアの石像かと思いました。
@user-ck4bp2nu7y Жыл бұрын
ماهو حجم هاذهي ماكنة الحام
@industrealjapan Жыл бұрын
ماكينة اللحام هذه عبارة عن لحام قوس نصف أوتوماتيكي 350
@no15211 Жыл бұрын
そもそもこれが何なのかを理解していないと序盤を見てもちんぷんかんぷんですね
@virtusleather Жыл бұрын
I wonder what Curtis would say
@bigredc222 Жыл бұрын
who is curtis?
@virtusleather Жыл бұрын
@@bigredc222 cutting edge engineering
@industrealjapan Жыл бұрын
thanks for watch I'm a big fan of Curtis from edo japan. I want to be as great as his channel, so please support me thank you
@191usinger4 Жыл бұрын
硬度が必要な爪部分はどうするか気になって見てましたがメーカーからの部品で有るのですね
@SatoshiTG Жыл бұрын
MADMAXっぽい仕上がり\(^o^)/
@kkkkkkk052000 Жыл бұрын
ここまで摩耗したら修理と新品どっちが安いんだろう?
@costiri Жыл бұрын
CONCRETE GODZILLA CRUSHER NEW TEETHING
@industrealjapan Жыл бұрын
thanx bro. i am ninja from edo japan.
@melin1969 Жыл бұрын
they certainly got thier monies worth out of the original jaw that thing was worn down more than the shawshank hammer
@user-ey8xc6nq2l Жыл бұрын
無駄にケチると余計な手間が増える例ですな…
@hibahprice6887 Жыл бұрын
The teeth for these and similar machines must be made of very strong and hard steel. The same steel from which punches and dies are made
@hibahprice6887 Жыл бұрын
But usually such steel is not welded.
@user-ln2wz7iy7u Жыл бұрын
Стоматолог динозавра))
@sly123size Жыл бұрын
An worn down bucket and claw can be replaced but it's too expensive buy one so this guy had to cut, rebuild, and restore the bucket and claw's true power after being used so many times
@zbeast Жыл бұрын
it's nice seeing someone working on heavy equipment with the necessary safety gear on. flip-flops and loose clothing just makes me cringe