Motion Sensor Light [ DIY ]

Рет қаралды 340,837

5 жыл бұрын

Motion Sensor AC Light [diy]
In this video, we will see how to make PIR motion activated light.
Things required:-
1) PIR Motion Sensor Module
2) Resistor
220 ohm
3) Transistor
2N2222
4) Diode
1N4007
5) Relay 5v
6) Power Supply 5v dc
(USB Charger/Mobile Charger can be used as power supply)
7) AC Bulb Holder
8) H Type Screw Terminal Blocks (optional)
-----------------------------------------------------------------------
-----------------------------------------------------------------------
Diagram:_-----------
drive.google.com/open?id=1lqV...
----------------------------------------------------
Other NPN Transistor that can be used
drive.google.com/open?id=1wrx...
------------------------------------------------------------------------
PIR Module Jumper Setting:-
drive.google.com/open?id=1pYc...
H: Repeat Trigger Mode:- In this mode light will be continuously ON if there is motion and when there is no motion light will turn OFF after delay time.
For example; If the delay time is set to 10seconds then, Light will be continuously ON when motion is detected and when you leave the detection area the Light will turn OFF after 10 seconds.
L: Single Trigger Mode:- In this mode Light will turn ON when motion is detected and light will turn OFF after Delay time. Light will turn OFF after delay time even if you are present in the detection area and again after some time sensor module will start detecting any motion
Turn ON the circuit, wait for 30 to 60 seconds now sensor will start detecting any motion in its range and act according to the mode selected. [This module will only detect motion done by any warm body such as human or animals]
Mode can be selected by adjusting the Jumper,, how??-- pull out the jumper, you will see three pins now put back the jumper to the H side or L side leaving one of the pin blank.
Sensitivity Adjust:- we can adjust the sensitivity or detection range of the sensor by adjusting the preset @ 0:21 . The detection range can be adjusted between 3 meters to 7 meters.
Delay time adjust:- when you leave the detection area Light will turn OFF after some delay; this delay time can be adjusted by rotating(clockwise or anticlockwise) the preset @ 0:22 .
This delay time can be adjusted between 5second to 300seconds.
Both the preset can be adjusted by slowly rotating it clockwise or anticlockwise; You can use a small screwdriver to rotate these presets.
-----------------------------------------------------------------------
PIR Motion Sensor Module
www.banggood.in/custlink/mvDv...
Relay 5v
www.banggood.in/custlink/DDDG...
Transistor 2n2222
www.banggood.in/custlink/mm3D...
H Type screw terminal
www.banggood.in/custlink/KKmD...
-----------------------------------------------------------======
Thank You for watching;
Hope you like this video
Please LIKE SHARE SUBSCRIBE & COMMENT.
Have a Beautiful day.
----------------------------------------------==================

Пікірлер: 319

@unitedcomputer8101 4 жыл бұрын

Thank you, this circuit is working. Thank you so much.

@vinothkumar-qn4bs 4 жыл бұрын

The íl p M.

@nwankwocharles1130 3 жыл бұрын

How many watts was your bulb?

@harasoranitin8351 2 жыл бұрын

Sir light bandh nahi honi chahiye eshke liye kya karna chahiye

@ethicalhacker1 2 жыл бұрын

I followed everything exactly but the bulb turns on as soon as switch on the power and stays on like a normal bulb, I had tested the motion sensor before using it, can't understand the problem, can someone please help? My 5v power supply provides about 5.8 v maximum, is this too much for the 5v navinex company relay?

@kinggamer8835 2 жыл бұрын

@@ethicalhacker1 same problem for me bro.

@esoofikader3135 4 жыл бұрын

KZfaq has several videos, but this was the best explained...5 stars to you, i made one light outside my main door and its working fine. Thank you.👏

@nischalthakur1892 3 жыл бұрын

सर मेरा नाम कमल कांत है मुझे 10 पी आर आई सेंसर कंप्लीट बने हुए चाहिए आप कितने का देंगे मेरे को मेरा नंबर 92127 19814 है

@nwankwocharles1130 3 жыл бұрын

How many watts was your bulb please?

@Shubham-po2tp 2 жыл бұрын

@@nischalthakur1892 कितने के मिले

@VarunRao009 10 ай бұрын

@@nwankwocharles1130 *LOOK LIKE 5 WATT.*

@vamosabv 3 жыл бұрын

What a comprehensive explanation with detailed instructions even in the description!

@citizengkar7824 Жыл бұрын

As others have stated, one of the best examples of this type of circuit. Clear & concise (given it is not narrated), with a nice clean, professional looking build.

@consumercourt 2 жыл бұрын

This video is the best. Very properly demonstrated without any confusion. Very neatly done. Thanks.

@vinaydhan6635 3 жыл бұрын

Thanku sir....Electronic meri hoby hai...isliye bahut chanal ko follow krte hai aur video v dekhte hai....pr aapne itne ache se Wireing ko explain kya hai...ki aap ka bataya koi v project banana...bahut easy ho jata hai....thanks.

@hariharan.n5599 Жыл бұрын

👍Professional touch can be seen throughout the video. Keep it up🙏

@ashu22online 4 жыл бұрын

It's working.. you are a star 🌟

@indikafernando5813 Жыл бұрын

You do it nice & clean. You gave me a new idea also. Thank you so much.

@Mehedihasan-dm2tq 4 жыл бұрын

Wow.... It's really true!!! 100% working...

@mdkaifali2163 4 жыл бұрын

explains everything very easily... awesome keep going sir...

@andresfigueira1868 4 жыл бұрын

Very good job man!!

@mustafak.shaikh5012 Жыл бұрын

..And this was a Perfect and detailed video after many..circuit working perfectly..thank you very much..!!

@technicalsohil4063 Жыл бұрын

nope

@jhana.2023 7 ай бұрын

Muito bom ! Simples e claro. Ganhou mais uma inscrita. 👍👍👍👍👍

@user-ez7fl1sm1e 4 жыл бұрын

سلام ، تشکر ، خیلی عالی بود

@thedesishow1223 4 жыл бұрын

Simple way. Easy way to understand..

@bob456fk6 4 жыл бұрын

Very nice video! Thank you.

@lifeofsabeen6665 3 жыл бұрын

Awesome work. 👍

@diegocabrera2307 3 жыл бұрын

great work, thanks 4 sharing

@rajeshmakwana2014 2 жыл бұрын

Thanks this circuit is working and I using in my class project

@ernestocardoso1911 Жыл бұрын

thanks! It helped me a lot, your videos are well explained! success!!!

@satyajitmandal4787 4 жыл бұрын

The best video on this topic.

@BIKRAMDAS-hm9by Жыл бұрын

Thank you so much bro itni acchea tarike se samjha ne k liye

@jawaharbabu1886 4 жыл бұрын

Superb explanation Thankyou

@rustamali8309 4 жыл бұрын

good explanation Nice 👍

@idubai7893 3 жыл бұрын

I assembling this ,very good ur videos

@dasarikiran1537 Жыл бұрын

TQ Somuch 🙏Sir This is very use full vedio

@thillairasankumaresan1974 4 жыл бұрын

Highly helpful

@astronic4522 7 ай бұрын

Verry well explanation👍🔔🙏 6:50

@VEERsciencePROJECT Жыл бұрын

Good idea

@-al-jinnzera8923 3 жыл бұрын

So Clean And Neet

@nimya8282 2 жыл бұрын

Thank you so much.it was my final yr project,worked well.also pls give circuit description to add to my project report

@Alex-Tdv Жыл бұрын

tu me sauves la vie pour mon MagicMirror :)

@avishkakalharadsilva8298 3 жыл бұрын

good work,

@user-hr5qg5vt2i 4 жыл бұрын

Thanks a lot

@DrNileshkumarVala 3 жыл бұрын

Very nice 👍

@tianzining 2 жыл бұрын

Analog rocks!

@adrianfg3148 3 жыл бұрын

Es un trabajo excelente. Gracias.

@nortok00 3 жыл бұрын

As others have mentioned this is one of the best videos detailing this DIY project. Thanks for posting! Do you have a video (or can do one) that details how to wire this with a plug socket instead of the light? I want to DIY a motion sensor that I can plug lights into (regular light bulbs like the ones shown in this video). I need to power a bunch of lights not just one bulb so want to plug a power bar into the motion detector. I can't seem to find anything. Your video is the closest I have come so I now know how to wire the PIR but I'm not sure how to wire up the plug socket portion of it.

@noname-cy9lx 4 жыл бұрын

So clear

@deepakeswaran 4 жыл бұрын

Working good

@pannalalb.k1552 4 жыл бұрын

Nice video

@maygirl4086 3 жыл бұрын

Boht maza aya

@kabandajamir9844 2 жыл бұрын

So nice

@anishgameingpokemonunite1227 Жыл бұрын

Super

@Islam-my-life786 3 жыл бұрын

Good job

@snnyhacksci.5984 3 жыл бұрын

Thanks

@luisdonaldoregueyrajoachin1346 2 жыл бұрын

Hello good afternoon, your video is very interesting and it helps me a lot to carry out a project that I am carrying out. Do I have a query, with this practice could I connect a diaphragm pump that works at 12V?

@tanojkumar4046 2 жыл бұрын

Nice

@gilman7608 Жыл бұрын

You can use bc 547 which i think is more common And the resistor could be 1k ohm too I had 470ohm i used that

@lakshanmadusanka5315 3 жыл бұрын

I want to know why to add diode. How to work diode on curcit. Thanks you sir. This is best one.....

@dariushkhorramtash9414 Жыл бұрын

this is a sample of professional video making. thanks for sharing 👌👍

@jimmyvaca9968 3 жыл бұрын

I want to replace the H terminal with another that you recommend

@jonnycullinane4098 Жыл бұрын

Hi, I am doing a similar project to you and I was just wondering what light bulb you used?

@sundaramurthig2813 3 жыл бұрын

Thanks for nice video Sir. Please answer me, Can I use an 7 watt or 9 watt ac dc inverter led bulb in this holder instead of normal led bulb, because to use in power cut time ?

@shamimahmed-ux4jy 3 жыл бұрын

Can i use 6v relay in this

@mpartha8103 4 жыл бұрын

I can use many pir at once?.I will use it on the stairs.

@ethicalhacker1 2 жыл бұрын

Can we use this same transistor for connecting the pir sensor to an led strip?

@fakhrurraziq5103 3 жыл бұрын

Can you explain how does it operate?

@talvinjohnson4555 4 жыл бұрын

Where do you get the light bulb socket?

@VivekGangwar02 2 жыл бұрын

I need to make this device for intrusion detection in farms, for the case I need it to cover a longer range. Is there any PIR sensor which comes with longer range? Or any way by which I can extent the range to atleast 30metres?

@anilkumargoel307 2 жыл бұрын

Can we use triac in place of relay Anil Kumar Goel

@EAZYSTOREONLINEINDIA 4 жыл бұрын

,👌👌👌

@nikrosmarinanikmohamad9132 4 жыл бұрын

Can I replace the power supply with batteries.... also can arduino uno also be used to put in the USB

@grandsonmasoud9753 2 жыл бұрын

Can l use 12v charger

@tibrewa6879 2 жыл бұрын

I cant find screw terminal what to do?

@Tumsakari 4 жыл бұрын

Whats the use of the transistor

@engr.irfansultan 4 жыл бұрын

I built the similar circuit but used a different transistor and a different resistor. The circuit works but response time is too slow. What can be the possible problem? us it due to the transistor and resistance or my sensor is faulty? Can u plz help.

@nishipaul3886 2 жыл бұрын

This video is great. I want to make one. Please tell me what is the name for the device used for attaching the parts by heating?

@HarshiClasses 2 жыл бұрын

soldering iron very inexpensive max price 350 rupees

@fggfdgdgfdgffdgfrfdg 4 жыл бұрын

the system only works when i contact the relay . what is the reason ? any support

@ManiMani-cl3du 3 жыл бұрын

Can I use Bc547 transister this circute

@jaysonjoson8241 4 жыл бұрын

What kind of bulb i can use .

@kishorekoli5138 Жыл бұрын

I don't know the internal diagram of relay used but according to me he is connecting the nc and common of relay instead of the coil of relay so how will relay work

@rustamali8309 4 жыл бұрын

why diode connect parallel with relay terminals ?

@skgamingandvlogs5550 Жыл бұрын

Can I use another transistor and resistor

@mr.science1379 3 жыл бұрын

Can i use 12 volt relay and 5 volt power suppely

@tanishkakiran2112 2 жыл бұрын

Can you please tell me how to do without the h screw 2 way terminal

@welcometosrilanka6195 Жыл бұрын

6v rilay can ?

@TheOnie1234 2 жыл бұрын

My usb cable has 4 wires. What should I do? . Should I just use the red and black and disgregard the other 2?

@tanmay93sarkar Жыл бұрын

Sir, can you please explain how to make a 12" automatic exhaust fan for kitchen?

@debom5346 2 жыл бұрын

Greetings, I need a help hand. I just connected the circuit to a control unit and my relay its not stable. What can be a problem

@welcometosrilanka6195 Жыл бұрын

Can a 6v rilay

@senly210 2 жыл бұрын

I want electrical mini projects

@relaymatik5984 4 жыл бұрын

You can use intching relay negative trigger pulse then set your pir sensor to 3sec cut time just like i create in our toilet room once you enter in the toilet automatically turn on the light until you finish shower the time is related in the relay because its latching and when you go out automatically turn off the light 😊

@bakhtiyaralam6696 Жыл бұрын

Can you please explain in detail…?

@ivonfortestrackerexplained5602 4 жыл бұрын

Where can I get the motion sensor to buy...urgently can you help

@artwithme5839 3 жыл бұрын

Can I use resistor sensor

@abhiramrayalla4584 2 жыл бұрын

can I use DL 5V relay sir

@pramodpatil167 4 жыл бұрын

Your video is so nice But I have a question Can we join buzzer of 5V instead of light

@snnyhacksci.5984 4 жыл бұрын

Replace relay with a 5V Buzzer,, kzfaq.info/get/bejne/gZeToLer1Z-UnmQ.html

@IbrahimsWorldVision 3 жыл бұрын

Can I use 12 v led light instead of Ac bulb?pls tell

@Gamers_Game_club 4 жыл бұрын

Can we make this without diode

@prathmeshchopade2213 3 жыл бұрын

How should I increase on time more than 6/10min

@wahidshaikh6206 Жыл бұрын

Isme 12 v ka relay laga de to chale ga kya

@SHAIKH_GAMING. Жыл бұрын

Bhai isme 12v ka relay chalega kya

@Shashik539 3 жыл бұрын

Sir will it work on door When I go from door does light will on automaticly?

@U2fan003 3 жыл бұрын

Hi, thanks for the helpful video! Do you have any recommendations on how to do the same, but instead of turning ON the light when motion is detected, the light turns OFF please? (no motion = ON / motion detected = OFF). Thanks again!

@snnyhacksci.5984 3 жыл бұрын

use N/C pin of relay in place of N/O pin. in the video you can see one of the relay pin is left blank, that pin is N/C pin of relay and the brown wire( 4:31 ) is connected to N/O pin of the relay. So, you just need to connect that brown wire to the N/C pin. .Thanks

@U2fan003 3 жыл бұрын

@@snnyhacksci.5984 Thank you very much for your help! It is appreciated. Will try it out.

@U2fan003 2 жыл бұрын

@suresh krishendeholl Hi Suresh, yes I had managed to have it turn off the light. We switched the cable on the relay to NC and COM.

@kimiris6946 Жыл бұрын

@@snnyhacksci.5984 hello thank you for the video it was great I just have one question if possible how the circuit was powered thank you

@riddhi6535 3 жыл бұрын

is this the type of light that turns on automatically if it senses something within its diameter/range? And will it sense other things like toys or metals as well ???

@snnyhacksci.5984 3 жыл бұрын

PIR sensor will only sense motion done by any warm bodies, such as Human or Animals.