www.JDSTurbos.com Installing a Manual Timing Chain Tensioner on a 2008 Yamaha R6R This will work for most any motorcycle. The install is basically the same. #tensioner #chain #motorcycle
Пікірлер: 53
@xavicastello14 ай бұрын
Changed it in my Fz6. Thanks
@joshuaschoonover40333 жыл бұрын
Better tutorial than APE’s website! For that I give a like and a comment. You are kickass!
@JDSPerformance253 жыл бұрын
Thanks buddy 👍🏻 Gotta give good info on a how to 🤣👍🏻👍🏻
@TheScratchOffKing3 жыл бұрын
Thanks bro!! Your awesome
@ayp8119 Жыл бұрын
Thanks for the video 👍🏼
@JDSPerformance25 Жыл бұрын
You’re welcome!
@robsonenduro33163 жыл бұрын
excellent vid! I guess such manual tensioner you have to check from time to time as chain gets older.
@jaydaintith3 жыл бұрын
Not as often as you’d think. As long as you’re not hearing any rattling you’re all good 👍🏻.
@JDSPerformance253 жыл бұрын
Agreed
@thechance1233 жыл бұрын
Good vid man, a couple of questions on it. Do you recommend doing the engine running portion of the cam chain check? Would the quarter turn in from the really loose setting be about the same as the quarter turn out from all the way in? I went to my local shop and they put one of these on my bike before I knew it. Not that it's particularly bad, I just like to check my own stuff, and it sounds a little tight. thanks
@JDSPerformance253 жыл бұрын
It’s best to set it before starting the bike...the last thing you want is it too be too loose and jump a tooth and ruin your engine! Yes you don’t want it too tight either..that’s what the 1/4 turn back does 👍🏻👍🏻
@SalAvilaProductions Жыл бұрын
I bought one off eBay for my bike also was the cylinder part of the tensioner way smaller than the hole on your and would you have an update on it
@yhzell4 күн бұрын
Hi, thanks for the video. Can i know where do u get the cct with oil passage blocked. Doesnt seem APE cct block this oil passage.
@zerosuba3 жыл бұрын
great vid thanks man. do you think if the bike started to rattle loud mid ride and lost power it would be too late for CCT? No oil leaks or smoke and bike will start up fine but sounds like marbles rattling.... I checked chain tension and exhaust side seems very tight im wondering if i caught it too late and it jumped timing or if a CCT would fix this? Thanks
@JDSPerformance253 жыл бұрын
Hmmm...as long as it still runs...definitely fix it and don’t run it anymore until you do 👍🏻
@Shawn8553 жыл бұрын
I'm reading the comments on how the ticking goes away when bike is warmed up, but my ticking only occurs after my bike is fully warmed up and riding around for over 10 mins. Could this still be the CCT or would it be the famous yamaha tick everyone is talking about. (03 r6)
@ritorod71213 ай бұрын
Did you figure it out? I hav an 03 as well
@Shawn8553 ай бұрын
@ritorod7121 never figured it out. Even changes the tensioner and still did it. Ended up selling it for 2x more than I paid for it.
@ritorod71213 ай бұрын
@@Shawn855 did you get your valve clearance checked too?
@ritorod71213 ай бұрын
@@Shawn855haha nice!
@throttle.therapy84443 жыл бұрын
Does it have to be a TDC to put the tensioner? Or is that just a extra step to be safe?
@JDSPerformance253 жыл бұрын
Extra step to be safe...as long as you turn the engine a full revolution and be sure the tensioner is set properly you will be fine. You seen me adjust it while the bike was running...just be very careful it isn’t too loose or the chain could jump a tooth and damage your engine.
@throttle.therapy84443 жыл бұрын
@@JDSPerformance25 thanks! I appreciate the quick reply!
@darbsK Жыл бұрын
If my chain is at top dead center could the tensioner still be the reason it gives it the rattling noise?
@JDSPerformance25 Жыл бұрын
It’s almost always the tensioner…unless you have a broken guide or the chain is stretched.
@darbsK Жыл бұрын
Okay thank you. My tensioner comes in today. Hoping it fixes my issue. Top dead center line seems a little difficult to find. Is it just at the bottom portion of the split? And I line the line above the T to it?
@darbsK Жыл бұрын
You go a full revolution on the tensioner bolt not the 12mm bolt where you turn it to top dead center correct?
@JDC_Portraits3 жыл бұрын
So if it’s too loose it’ll make a ticking noise is that correct? I have a ticking noise on my R1 when it’s starts up but goes away after it’s warmed up.
@JDSPerformance253 жыл бұрын
Yes that is correct.
@joshharrison11693 жыл бұрын
that's what my r6 is doing im scared to mess this up
@JDSPerformance253 жыл бұрын
The video shows you how to do it 👍🏻
@JDC_Portraits3 жыл бұрын
@@joshharrison1169 I replaced it myself with the stock TCT. It took forever because 03 gen was located by the frame. I had to take the gas tank off and air box. Still was a very tight space. After replacing the ticking noise only appears for a few seconds after start up and then disappears. Better than constant ticking from before
@joshharrison11693 жыл бұрын
i have an 07 r6 is it possible to get a new TCT from stores ? i dont wanna wait for this i want to get this done now
@EdwinGastelum2 жыл бұрын
I tried doing this but i cant turn the engine is there a reason why?
@JDSPerformance252 жыл бұрын
I need alot more information please
@lucaric6935 Жыл бұрын
ur head gasket leaks? fixed?
@JDSPerformance25 Жыл бұрын
Head gasket leaks??? This is a timing chain tensioner rattle fix video 👍🏻
@chuckhooper252 жыл бұрын
What Cam tensioner is this one
@JDSPerformance252 жыл бұрын
I got it off ebay 👍🏻
@yyyqqq10823 жыл бұрын
Locktight on the Nut?? or should be fine as is?
@JDSPerformance253 жыл бұрын
No the rubber o ring will hold it in. No loctite needed 👍🏻
@yyyqqq10823 жыл бұрын
@@JDSPerformance25 cool. i appreciate the quick reply. also. whats the lifespan on the timing chain? bike only has 30k. miles. its a 06 yamaha r6. has the same ticking sound in a video i just watched and im pretty sure it will go away with a manual tensioner. by just looking at the chain can you get some kind of indication of the wear and tear?
@JDSPerformance253 жыл бұрын
@@yyyqqq1082 Pretty rare they ever go bad...they could stretch but it’s very doubtful...Mine has 50k and she gets rode hard 👍🏻
@zj33447 ай бұрын
Maybe it's time to change timing chain? Maybe it got old?
@JDSPerformance255 ай бұрын
No this is a common problem. The factory tensioner wears out before the chain does.
@geneticmonster82 Жыл бұрын
oh damn I definitely over tightened mines ....definitely didn't do it by hand...I need to address that asap b4 I continually murder my bike