Mounting Rear the Sprocket Adapter | Motorized Bicycle

Mounting Rear the Sprocket Adapter | Motorized Bicycle | BikeBerry

Рет қаралды 9,891

Күн бұрын

Learn how to mount a Rear Sprocket Adapter to an HD wheel with BikeBerry.com for motorized bicycles! In this video, you'll find an overview of the process for mounting a Rear Sprocket Adapter for your motorized bicycle from BikeBerry.com. Discover the features of mounting a Rear Sprocket Adapter, as well as how to do it correctly. Get the information you need to make the best decision for your motorized bicycle needs with BikeBerry.com!
Buy Rear Sprocket Adapter here 👇
www.bikeberry.com/products/bb...
F-Zero Bike Like Tony’s
www.bikeberry.com/products/bb...
***Every single part mentioned can be purchased here 👇👇👇👇👇****
BikeBerry.com ►bit.ly/1FZ8nPp
Facebook ► on. 1wWG4fD
Instagram ► bit.ly/1aM3WxZ
Twitter ► / bikeberrycom
****Everything you need to make your own Motorized Bicycle.****
Chapters
0:00 - Introduction
0:10 - How-To Install Adapter
1:20 - Evenly Tighten Adapter
3:10 - Tighten Locking Bolt
3:16 - Thanks For Watching
#motorizedbicycle #bikeberry #sprocketadapter #motorizedbicycle (product category) #motorizedbike #motorizedbicyclesprocketadapter #motorized #bicycle #sprocket #motorized #bicyclerearhubadapter #motorizedbicyclesprocket #motorizedbikesprocketwheelhubadapter #dischubmotorizedbicyclesprocket #sprocket (bicycle component)

Пікірлер: 36

@jmdunwoody Жыл бұрын

Have you tried drilling a hole in the hub for the jam bolt once the offset is set? That seems easier than making a channel and key way.

@terranceturnbow8184 10 ай бұрын

Than the bolt will rub against the axle and probably at some point snap in half

@grendelsgarage9723 Жыл бұрын

Good stuff thanks man!

@cnccontroller 10 ай бұрын

Hello! Sorry for my English. Rubber rings provide cushioning. Depreciation will disappear with such a mount. What to do in this case? Depreciation is very important .

@Bobs-yer-uncle Жыл бұрын

I've had great experience with the clamps I think the spacing is the part most people forget or over look or don't understand how a clamp works in the first place in my opinion that set screw isn't necessary if set up correctly

@tonytaylor5087 Жыл бұрын

Yup, the spacing is super important. I’ve just started tapping in the set screw and so far it’s been good insurance.

@bryduhbikeguy Жыл бұрын

Wish I'd had the screw option on mine.I used 1 that slipped and I tightened it enough that it crushed in the center of the hub and it still slipped.I ruined 2 rims by having spokes ripped out.Next time,I'll use a screw like that,and put a bab of grease on the tip of it to mark where to drill a hole for it and remove the mount,drill the hole,and put it back on and put the screw Into the hole.Just tightening a screw like that will still leave it possible to slide.Thanks for the idea Tony.

@tonytaylor5087 Жыл бұрын

I drilled and tapped that set screw in there. There’s a video on it. I do that or cut a key way in there.

@bababla8528 10 ай бұрын

@@tonytaylor5087do you just drill in a little bit you don't go all the way through right

@danbieche5382 Жыл бұрын

I think that that's hub adapter is the correct idea. I tried to mimic that top end Titan bolt. Under torque the unit still slipped. The best way ultimately as you know is to add a channel and a key way in the sprocket assembly. Truthfully I wish they would just come up with a better thing altogether.

@tonyzee1195 7 ай бұрын

Wrap your hub with a strip of rubber cut from an old tire tube and thank me later 😂

@SniperSpade Жыл бұрын

Cutting some double sided sandpaper exactly to fit/wrap around your hub in between the hub and adapter will help slippage. Give it some grit to bite onto. They sell it at plumbing supply houses. Us plumbers call its "sand cloth"

@JoseDiaz-ug1xo 8 ай бұрын

Gonna try that out thanxs!

@tonyzee1195 7 ай бұрын

A strip of rubber wrapped around the hub works too, cut it from an old tire tube

@SniperSpade 7 ай бұрын

@@tonyzee1195 very good idea

@187dario Жыл бұрын

can you guys make a video on how to mount the offset mount for bikes with wider frames?

@tonytaylor5087 Жыл бұрын

What offset mount are you talking about specifically?

@nicos9937 Жыл бұрын

How many spokes are on each side of rim I'm having trouble mounting the adapter at a correct angle

@DeadSharkOG 14 күн бұрын

This works with mountain bikes right?

@amealnet2495 8 ай бұрын

How do you prevent it from slipping?

@vanderley43 Жыл бұрын

Compraria de você uma roda dessa já completa para o uso da minha motorizada você vende para o Brasil?

@nicos9937 Жыл бұрын

Anyone know a 700c rim that would fit this adapter?

@TalariaMonster413 Жыл бұрын

Is that the bbr free wheel? And what size adapter is that?? I want to try the free wheel instead of coaster brake

@TalariaMonster413 Жыл бұрын

What size adapter did you use and how did you do that screw on top of adapter

@Knifeinyolife Жыл бұрын

Hi, you put the sproket adapter on a rear rim that has disk brake adapter? Is that correct?

@tonytaylor5087 Жыл бұрын

Yup, that way I can space the two apart correctly.

@Knifeinyolife Жыл бұрын

@@tonytaylor5087 i have that same rim and didn't use it cause it had a disk brake adapter. I always wanted to use it due to the free wheel. I guess that's next weeks project. Thanks 😊.

@craigcoffman69 10 ай бұрын

Is there a way to connect sprocket to shaft/hub without spoke mounting? That's a twice a year failure point. You would think some enterprising young lad with a welder would be selling rims with hard point flanges.

@destinatwood9987 Жыл бұрын

Where'd you get that sprocket adapter

@dustinh4175 Жыл бұрын

Ebay has some nice ones

@c.rutherford 7 ай бұрын

I just can't decide on this this. To me the CNC rear sprocket adapter looks superior in that it can hold the sprocket true and aligned so the chain doesn't come off when riding. But unfortunately unlike the rag joint which displaces the torque evenly on all the sprockets at once... this adapter instead puts all the pressure of torque on a much smaller axis and its all carried on one single bolt. Not to mention the danger of ripping out all the sprockets if it slips. So is this an inferior design to the rag when its all said and done, or is it really better? Would appreciate comments

@1949kf Ай бұрын

Rag joint is superior as long as the Rags are decently equal in thickness to allow the sprocket to run true and prevent runout