Excellent! I use Warne Maxima rings which is very similar with a Tikka T3X...the Warne Maxima ring has the recoil pin that fits in the recoil hole in the receiver. No bases or rail required which saves weight and cost.
@nmelkhunter15 жыл бұрын
Great video. It certainly covers the right way to do things. What cartridge is that Finnlight in?
@outdoorquesttv99465 жыл бұрын
6.5 Creedmoor.
@EduardoDGarza-mq4xu4 жыл бұрын
Could you please inform me if the tube diameter is 30mm or 1", does it work for a Sako Finnbear the luxe .270, also could you tell me the type of screwdriver that you use in the video. Thanks a lot, great video
@outdoorquesttv99464 жыл бұрын
This was a 30mm tube. Don't see why it wouldn't work the same on the Finnbear. The screwdriver is made by Caldwell.
@jd7tull4 жыл бұрын
Hi, Thanks for the great video. It looks like you are using a Wheeler Fat Wrench, but all of the ones I see online only go up to 65 inch-pounds. Did they used to make a stronger one to get up to 80 inch-pounds, or have I incorrectly identified your torque driver? If so, what kind are you using? Cheers
@jd7tull4 жыл бұрын
hey?
@outdoorquesttv99464 жыл бұрын
You are correct about the Fat Wrench...we torque it to max then give a slight bit more.
@Hollywood416423 жыл бұрын
2:12 If u move the front ring up to the right to change ur point of impact, but the back ring always stays straight aren't u bending ur scope tube ?
@bryonslatten31474 жыл бұрын
Did that adjustable cheek piece come with the rifle or is it an aftermarket stock?
@outdoorquesttv99464 жыл бұрын
It's standard on the Finnlight II
@johnharris37614 жыл бұрын
hi, where did you get the base torque setting of 80 inch pounds from? that is almost twice what i have read elsewhere
@outdoorquesttv99464 жыл бұрын
It's what Sako recommends.
@zeissOholic4 жыл бұрын
@ Outdoor Quest TV - 80 inch lbs is the torque for the base on the two piece mounts, not the ringmounts. From Beretta USA for the ringmounts - Optilock ring screws: 15/17 inch lbs - Optilock bases screws: 45 inch lbs. www.eurooptic.com/PDF/Optilock-Tighting-Instructions.pdf
@westesh4 жыл бұрын
I just mounted the same rings on a AV action. The action is so long that I needed to mount the front ring on the rear of the tapered dovetail which means the dovetails are not fully engaging, just the tighten screw is holding it. Is this ok or should the dovetail be fully seated (tight) on both sides?
@outdoorquesttv99464 жыл бұрын
Sounds like you need extended bases. I wouldn't trust the way you have it mounted.
@westesh4 жыл бұрын
@@outdoorquesttv9946 I will look into it, thank you!
@Alpha_Wolf.4 жыл бұрын
Great video what size is the objective bell
@outdoorquesttv99464 жыл бұрын
42mm
@Alpha_Wolf.4 жыл бұрын
Outdoor Quest TV could u have gotten away with a 50mm objective on the same ringmounts ?
@outdoorquesttv99464 жыл бұрын
@@Alpha_Wolf. I believe so
@user-no9qb6lj7c3 жыл бұрын
What hight rings would you use for a nightforce nxs 2.5-10 42mm
@outdoorquesttv99463 жыл бұрын
The One-piece only come in one height.....it's about equal to a low two piece.
@user-no9qb6lj7c3 жыл бұрын
@@outdoorquesttv9946 alright thanks !
@pwade80803 жыл бұрын
I always use the same bubble. Using different ones can give you a scope off level.
@outdoorquesttv99463 жыл бұрын
Never experienced that. Levels are pretty simple devices by design but can't argue that it wouldn't work!