MS261C 325 vs 375 Chain in Oak.

Рет қаралды 5,304

japoquet

Жыл бұрын

Testing .325 stock chain against 3/8" (.375) chain in 18" oak log.

Пікірлер: 16

@Cacheola Жыл бұрын

I'm still running .325 with my 261cm. She revs too high for my liking with the stock chain in 20", so I tend to file the rakers a bit more. The larger diameter 3/8 sprocket will spin the chain at a higher RPM. I'm tempted to switch over... especially if I open up the muffler and port it. I cut mostly SPF

@japoquet Жыл бұрын

I agree with you. Thanks for the feedback and sharing. LMK how the muffler mod and porting turn out.

@Cacheola Жыл бұрын

@@japoquet will do. You got me thinkin, I'm gonna try a .325 8 pin on this softwood, that'd probably mellow the saw out nicely without over filing the rakers

@maxballiet8632 Жыл бұрын

I’m a big fan of that Stihl sharpener

@japoquet Жыл бұрын

Agreed. It does a really nice job.

@lailer1975 Жыл бұрын

.325 is the way to go on the 261. It’s not designed to pull 3/8, it will pull it but you’re going to shorten the life of your saw.

@japoquet Жыл бұрын

I think you're probably right. I switched the saw back to the .325 for a while and now just switched it back to 3/8. I like the 3/8 chain for limbing, but when cutting larger diameter I understand what you mean about being a little too much work for the 261. I'm going to try setting the rakers higher and see if it still takes chips, but cuts easier. For the big stuff I use my big saw 500i. Thanks for your feedback

@lailer1975 Жыл бұрын

@@japoquet yeah, if you have a 500i as a second saw put the heavy lifting on that. Different saws, different uses. My other saw is a 462, that gets used for bigger work. I really wanted to grab a 500i, but they were unavailable when I picked up the 462 a few years ago.

@japoquet Жыл бұрын

@@lailer1975 that 462 is a great saw too. I had a 461 before I got the 500.

@gwp1ohio 10 ай бұрын

I tried changing to 3/8 on my 261 and realized it was a waste of time. If I'm going to use a small saw. I just stick with my good old MS310 way better saw and more power.

@stihlhead3338 7 ай бұрын

I was just about to tryout my 20" 3/8" bar on my ms261cm. I wonder what a 8 pin rim sprocket would do on the 20" bar. Good stuff man really enjoyed the video!

@japoquet 7 ай бұрын

I was cutting some large ash last night and the 7 pin 3/8" 20" bar setup was working well until the wood diameter got into the 8-10" range. I like the reach of the longer bar, but I don't think the 261 is powerful enough for large diameter. I sharpen using the 2 in 1 and the rakers are set a little aggressively for hard woods. The 500i was ripping through the 24" ash though! If you try the 8pr lmk how it works!

@richardsneddon2976 2 ай бұрын

Really you want to know what an 8 pin 3/8 sprocket would do on a stihl ms261 with a 20 inch bar . Simple the 261 50cc saw would never pull that unless you are cutting twigs or branches and as soon as you went into say something around 15inch or bigger in diameter the saw would just bog straight down as it doesn't have the torque. Even a 60cc saw would struggle unless you are talking about 3/8 pico you know the small size chain then it may be ok .

@richarddodds9326 11 ай бұрын

If that saw is too weak to pull 3/8 chain i' m not gonna buy one. I think the Saw needs to be tuned richer in under full load. That burns more fuel, makes more power and runs cooler.