MSC ADAMS Tutorial - Flexible Body Analysis I Stress Analysis of Moving Bodies in ADAMS

No video

MSC ADAMS Tutorial - Flexible Body Analysis I Stress Analysis of Moving Bodies in ADAMS

Рет қаралды 21,076

4 жыл бұрын

In this tutorial, it is explained that how to do stress analysis of the multi body system with ADAMS flex body.
1. Steps performed
- Geometry Import
- Material Application
- Joints and constraints
- Rigid to flex body conversion
- Post Processing
Link for file - drive.google.c...
patreon link - / 3dtechnocrafts
1. Mohr Circle Python Program - • Python For Mechanical ...
2. Robot Simulation with ADAMS - • Robotic System Simulat...
3. All Terrain Vehicle Analysis with - ADAMS - • All Terrain Vehicle Si...
4. Excavator Simulation with ADAMS - • Excavator Simulation u...
5. SFD and BMD using Python - • Python For Mechanical ...

Пікірлер: 55

@beefybeef1326 2 жыл бұрын

Thank you very much for this brilliant tutorial. Very well explained. Great channel. Subscribed!!

@priteshwalke 3 жыл бұрын

Great job buddy.. please upload more videos. Can please make videos on all Adams toolbar information.

@dodoq4505 2 жыл бұрын

Thanks a lot!!!

@alexkon6218 4 жыл бұрын

very good material! Thank you a lot, keep it going!

@3DTechnocrafts 4 жыл бұрын

Thank you. Please share within your circle

@yd9012 3 жыл бұрын

good! keep going

@limkwerly8508 3 жыл бұрын

very very helpful for me ~~~

@ferhatturkmen569 3 жыл бұрын

eline sağlık kardeşim

@kyrilloswilliam7626 3 жыл бұрын

First of all, you did a great job. but I have a question. Why did you change the Location Center of mass for every part? I think you should let it so

@manfioruffano 2 жыл бұрын

Hallo Sir, great job. Please I would need your opinion about the interaction and collision between rollers elements and cage of a bearing. The scope is to see the forces acting on the cage pocket from the collisions during rotation. Is it possible by Adam to get this information? And then by FEM processing the input as load macro, combined with additional centrifugal effect? I would really appreciate if you cold give me your help. Thanks in advance Best regards

@eunkwang13 3 жыл бұрын

Thank you!

@digambarkashid6332 4 жыл бұрын

Very informative and useful

@3DTechnocrafts 4 жыл бұрын

thank you

@Hiei104 4 жыл бұрын

thank you very much

@nabeelk 3 жыл бұрын

Thats really amazing. Are you planning to upload more videos on ADAMS ?

@3DTechnocrafts 3 жыл бұрын

Yes

@sudhanshupandey9833 2 жыл бұрын

When i define the material for some geometry in imported model , i got error as"The reference marker of an extrusion, revolution, or shell must belong to the same part as the extrusion, revolution, or shell". how to solve this error,? please help me

@3DTechnocrafts 2 жыл бұрын

May be you can delete markers associated with geometry except PSMAR after import then try to apply material property

@imampatrick 2 жыл бұрын

Sir please help, when I open durability plug-in and try to find hot spots, it says no data was found. When I try to find nodal plots it says no stress data in mnf of flex body. HOWEVER there is clearly stress and strain available. I can see it in the simulation as well. What could be the problem?

@3DTechnocrafts 2 жыл бұрын

You have to define the what outputs you want while creating mnf

@3DTechnocrafts 2 жыл бұрын

Also in some Adams version it doesn't show hotspot before 2017 version

@imampatrick 2 жыл бұрын

@@3DTechnocrafts Ohhh okay thanks a lot

@imampatrick 2 жыл бұрын

Sir thanks a lot. I have a few questions. First of all what do the contour stand for at 20:07 ? Is it stress, is it displacement? At that point no force was acting on the system, the only parameter you defined was MOTION which is a kinematic parameter, no? So I am having hard time understanding what is changing inside the flex part. I think it can't be stress or displacement since there is no force. So I am asking that, what does that contour change stand for and why? After that you defined a force. Now, the only reason behind defining the force was to observe the flex parts' displacement and stress values right? If that solid was not flex, and rigid instead, defining the force would literally mean nothing since there is a motion defined and it overrides force. Is my assumption correct? I hope you answer, thanks a lot for creating ADAMS documents, there really are not much around.

@3DTechnocrafts 2 жыл бұрын

even if there is no external force there is weight of the moving parts will act as force. As rotational angle changes the weight components will also change (horizontal and vertical force) hence there will some force as well as deformation.

@imampatrick 2 жыл бұрын

@@3DTechnocrafts ah I understand thanks a lot, but other than that, defining a motion overrides all the forces in terms of kinematics right? Forces then only act on stresses and strains

@3DTechnocrafts 2 жыл бұрын

@@imampatrick no it will consider force when motion is also applied You can check in post processor also the forces

@imampatrick 2 жыл бұрын

@@3DTechnocrafts So you defined motion to crank and then defined force, is the crank's or crank shaft's velocity going to change now that there is also force being applied?

@mahenjoshi6486 3 жыл бұрын

Great job sir. Can you please throw some light on How to measure Contact Stress in Flex model contact definition ?

@sanjeev9646 2 жыл бұрын

this is really very interesting, can you please help out where I can get to learn the basics of msc, from past 3-4 months I was trying to understand this software but couldn't found any real course, from where I can to know about the basics of these?

@3DTechnocrafts 2 жыл бұрын

You can get Adams tutorial kit to download from net as well as you can enroll for msc e learning cource

@limkwerly8508 3 жыл бұрын

Good day sir, may i ask i have to test run my rotordynamic model (Just flywheel and suppporting shaft), can i use joint-related icon as well, such as revolute, joint connection and so ? ~ Thankyou ~~

@3DTechnocrafts 3 жыл бұрын

I recommed to use Nastran for rotordynamic

@limkwerly8508 3 жыл бұрын

@@3DTechnocrafts I see, i have Nastran as well, may i ask can I find the torque required to rotate my model in ADAMS first, or i too can get it as well in Nastran ? Thankyou for replying me ~~~

@3DTechnocrafts 3 жыл бұрын

@@limkwerly8508 yes you can find in Adams

@3DTechnocrafts 3 жыл бұрын

@@limkwerly8508 if you know stiffness values use bushing instead of revolute joint

@limkwerly8508 3 жыл бұрын

@@3DTechnocrafts ok i will try it. Thankyou Sir. ~~~

@sekolahonlineteknikotomotif 3 жыл бұрын

Brother, you've done awesome videos in ADAMS! Appreciate that so much! By the way, do you learn ADAMS by yourself, or is there any book or courses or sources that you recommend? Could you please inform me about this?

@3DTechnocrafts 3 жыл бұрын

Most of I learned on my self along with you can go through MSC e learning course

@sekolahonlineteknikotomotif 3 жыл бұрын

@@3DTechnocrafts Thank you very much for your reply! Can't wait for your next video tutorials! :)

@armaganalkan1661 2 жыл бұрын

Thank you very much for this video, do you know anything about max-flex for non-linear part. Can you help me about that pls

@3DTechnocrafts 2 жыл бұрын

I have no command on max flex

@armaganalkan1661 2 жыл бұрын

@@3DTechnocrafts how can we define geometric non-linearity do you know that ?

@3DTechnocrafts 2 жыл бұрын

@@armaganalkan1661 you cas FE part section in Admas - here is link I have one video on FE parts kzfaq.info/get/bejne/arKcp5tjysqtY30.html kzfaq.info/get/bejne/d9KFgJWcrdXSqYk.html