My 2024 Pedalboard Setup for Praise and Worship

My 2024 Pedalboard Setup for Praise and Worship | Walkthrough and Demo

Рет қаралды 8,395

Күн бұрын

In this video I share with you my newly completed pedalboard setup for 2024. I have been using this pedalboard to play guitar at my church for the past few months. I walk you through the pedal signal chain and share how I use each pedal. Leave a comment below and let me know any questions you have about the board, signal chain, or pedals.
Table of Contents:
00:00 - Introduction
01:14 - Pedalboard Overview
02:47 - Signal Chain
04:38 - Midi Setup
05:26 - Peterson Tuner
06:07 - Case Study Compressor
07:47 - Browne Carbon X
09:56 - Jackson Audio Optimist
11:52 - Line 6 HX One
15:09 - Strymon TimeLine
16:13 - Strymon Cloudburst
17:36 - JET Pedals Revelation
19:05 - Pirate Midi Bridge 4
20:06 - Putting it All Together
20:42 - Lessons Learned
Gear in This Video:
PRS SE DGT
Creation Music Company Cables
Temple Audio Duo 24
‪@PetersonTuners‬ StroboStomp HD
‪@casestudyeffects‬ Studio Compressor
‪@BrowneAmplification‬ Carbon X
‪@JacksonAudio‬ Optimist
‪@jimdunlopusa‬ Mini Volume X
Line 6 HX One
‪@strymon‬ TimeLine and Cloudburst
‪@jetpedals‬ Revelation
‪@PIRATEMIDI‬ Bridge 4 Midi Controller
‪@ikmultimedia‬ Tonex Pedal
‪@worshiptutorials‬ Tonex Captures (AC30 + Matchless Clubman)
‪@pinstripe_pedals‬ DISO+
CIOKS DC7 Power Supply
🎛️ My Pedals:
Amp Modeler (Tonex Pedal) - sweetwater.sjv.io/Mmz7Qo
Small Amp Modeler (Tonex One) - sweetwater.sjv.io/eK7Dd6
Favorite Reverb - sweetwater.sjv.io/q49YgL
Favorite Klon - sweetwater.sjv.io/5gEojN
JHS Morning Glory - sweetwater.sjv.io/DKG7L2
My Tuner - sweetwater.sjv.io/9gD0e5
My Volume Pedal - sweetwater.sjv.io/k0EYRL
Swiss Army Knife - sweetwater.sjv.io/GmJ7nm
My Delay Pedal - sweetwater.sjv.io/1rBJ19
________________
🔴 My Studio Gear:
Audio Interface - sweetwater.sjv.io/JzX7Jq
Studio Monitors - sweetwater.sjv.io/ZQ57XX
Shure SM57 - sweetwater.sjv.io/XYj7dX
Shure SM81 - sweetwater.sjv.io/Wqr74A
Headphones - sweetwater.sjv.io/nLxYNA
________________
🎸 My Guitars:
PRS SE DGT - sweetwater.sjv.io/6eLmAq
PRS SE Silver Sky - sweetwater.sjv.io/21zZj7
Gibson J45 - sweetwater.sjv.io/R5q71N
Fender Classic Player Jazzmaster
Fender American Standard Telecaster
________________
🎧 My Accessories:
Budget In-Ears - sweetwater.sjv.io/q49YAY
Fancy In-Ears - sweetwater.sjv.io/xkaYy1
Electric Strings - sweetwater.sjv.io/jr0YzP
Acoustic Strings - sweetwater.sjv.io/5gEoA2
Favorite Picks - sweetwater.sjv.io/GmJ70m
Favorite Straps - sweetwater.sjv.io/JzX7Lq
Patch Cables - sweetwater.sjv.io/XYj7LX
#pedalboard #guitar #praiseandworship #geartalk #sundaysetup #strymon #line6 #tonexpedal #guitarpedals #worshipmusic #ambient #jimdunlop #compressor #overdrive #effectspedals #knowyourtone #prsguitars #fender #worshippedalboard #sundaytone

Пікірлер: 47

@casestudyeffects Ай бұрын

Great build, man! I’m rebuilding my board right now, so I’m here for the inspiration!

@sundaytone Ай бұрын

Thanks man!

@stevelife8505 Ай бұрын

The Jackson Audio Optimist has been my go-to for drive, such an underrated pedal!!!

@sundaytone Ай бұрын

Yea - it's great!

@PetersonTuners Ай бұрын

Fantastic build and walkthrough!

@sundaytone Ай бұрын

Thanks for checking it out - love the StroboStomp!

@pinstripe_pedals Ай бұрын

Ayyyy! Thanks for taking us along for the toanz!

@sundaytone Ай бұрын

Always!

@joemiller9856 Ай бұрын

Great build and tones. I wish I could find someone at a reasonable price to build a board myself. I’m using an all in one modeler now for simplicity. I’m using a headrush prime now but looking to get back to the fractal world with the FM3 .. the prime is a beast to lug around and although a great value ongoing support with updates and engagement with their user community has been lacking. Another alternative would be a hybrid board with Tonex for amps and perhaps a line6 or other small modeler that can change settings on the Tonex via midi. Enough about my journey… well done on the video! Thanks

@sundaytone Ай бұрын

Thanks so much!

@ElyVaz_ Ай бұрын

Great video and explanation of your setup! 🔥

@sundaytone Ай бұрын

🙏 Thanks bro!

@natekincaid9342 Ай бұрын

That optimist is quite the upgrade from the Mosky! Awesome board and great tones! Thanks for sharing!

@sundaytone Ай бұрын

Thank you! Yea - the Optimist is awesome.

@guitarnoodles7576 Ай бұрын

Nice set up! Super clean. Thanks for sharing. It’s really interesting to see other set ups. Very helpful! I am using a cloudburst and an older v2 Revelation at the moment too. I’ve been using a HX effects as a midi controller for wet effects and been happy other than the size. I preordered the Jet Unity 6. Hoping to post the new set up after that gets here. Great content. Keep it up!

@sundaytone Ай бұрын

Thanks so much! The Unity 6 looks awesome. I want to try that out at some point.

@ZachBrownMedia Ай бұрын

Sounds good! Picked up a Bridge4 last year and love it. I also have a Duo24 and ran into the same cable issues.. you've managed to make yours look cleaner than mine haha.

@sundaytone Ай бұрын

Thanks man! Yea - I like the board but was surprise that I couldn't fit some cables through there. Underneath the board is kind of a mess 😂. I didn't try to clean up the cables underneath just because I like to change things up so often.

@ThatMexicanGuyInUSA 27 күн бұрын

Nice video and awesome pedalboard man! I liked your way of stacking delays and of course the overall sound. You didn't mentioned what captures are you using, so, I have to ask, what captures are you using?

@sundaytone 27 күн бұрын

Thanks man! In this video I was using the Worship Tutorials AC30 and Matchless Clubman.

@ThatMexicanGuyInUSA 27 күн бұрын

@@sundaytone oh great! How did you dial the input trim on ToneX? What level are you at?

@WorshipGuitarSound Ай бұрын

Crowns Down part sounded great!

@sundaytone Ай бұрын

Thanks! Yea - great song.

@worshipartistry Ай бұрын

Looks good dude! I've been looking into get a midi controller, looking into the pirate mini bridge 4 now. Thanks!

@sundaytone Ай бұрын

🙏 Thank you! Yea - it's a great midi controller if you want something small.

@npisaacs 27 күн бұрын

I had a similar issue with noise and my strymon pedals with midi using trs. The fix for me was to use a solderless or soldered ts cable but disconnect the ground on one side. The strymon in particular only uses the tip to receive midi commands, so the ring and sleeve are not needed. Hope this helps!

@MarekUrbanowiczGuitar Ай бұрын

1. Strymon pedals can cause MIDI ground-loops - Morningstar mentions it in their manuals. Strymon sells those filtered MIDI cables (expensive...) which should address these issues. 2. Are all your pedals on separate power outlets? If you daisy chain some which are connected by MIDI it can go crazy with noise.

@sundaytone Ай бұрын

Yea I have seen those Strymon cables. I haven't tried one yet though. And the only pedal that is daisy chained is the compressor off of the tuner. Everything else is on separate power from the DC7.

@MarekUrbanowiczGuitar Ай бұрын

@@sundaytonehave you checked unplugging tuner? Vertex mentions in one video that surprisingly tuners can mess up a lot of

@saint__andrew Ай бұрын

Love it, sounds really great as always man! Do you feel limited at all with the Bridge4? Thought maybe you'd be jumping on the jet unity train when I saw that announced.

@sundaytone Ай бұрын

Thanks man! No I haven't felt limited yet - only limited by my time to program stuff before a Sunday 😂. But yea I would love to try the Unity out - it looks awesome. Might have to move some stuff around to try to fit it in. I also want to try to fit in a Tonex One to use for drive captures.

@saint__andrew Ай бұрын

@@sundaytone Heck yeah. It's so handy as a drive pedal! Highly recommend it.

@blakeparadise9998 Ай бұрын

Hey man! I experienced the same issues. I found that it was actually the junction box coupled with sending midi clock. Try plugging straight into your pedals and then straight from the jet to your amps (amp sims). It should go away. I tried different midi cables, junction boxes, etc. Think those junction boxes need to be buffered to curb that midi clock noise.

@sundaytone Ай бұрын

Oh I didn't think to try that. I'll have to see if that fixes it - thanks!

@mrsmithxii Ай бұрын

Now I want a midi controller lol

@sundaytone 27 күн бұрын

They are super helpful when you want to switch a bunch of presets all at once.

@jamesledbetter2888 Ай бұрын

I recently built a midi board like yours and I am having noise issues as well. I think my issue is mostly related to my H9. Still troubleshooting, but running into my UA Ruby, things get pretty noisy… changes coming. Great video!

@sundaytone Ай бұрын

Thank you! Yea - I only get the noise sometimes which is frustrating. A few times it has been so bad I had to just unplug the midi cables going into my Cloudburst and Revelation and use those without midi running to them for the set.

@saint__andrew Ай бұрын

@@sundaytone If you have lights on a dimmer on the same circuit you're plugging into, or are setting up at a desk with a computer w/lots of extra electrical activity going on, it could def exacerbate the noise issue. I'm constantly battling this in my home studio too and it can be frustrating!

@jon5546 Ай бұрын

Hi, with your 2 tonex, is the diso polrev a necessity? Or would your walrus canvas stereo be able to do the job as well? Saw you were using wt ac30 and wt matchless, do those captures have phase issues? Thankyou. I always enjoy your content😁

@sundaytone Ай бұрын

It's not a necessity but it's the best option for me. The WT AC30 and Matchless Clubman I use a lot don't have phase issues. So for those the Canvas would work. There are other amp combos I use where having the ability to flip the polarity is useful. It just opens a wider range of captures that you can use together but you can certainly find ones that are in phase.

@jon5546 Ай бұрын

@@sundaytone thankyou! I might keep the canvas for the time being then

@ryanpappenfuss Ай бұрын

I, too, had midi issues with jet pedals. Eternity would NOT sync to midi clock being transmitted to it, although only sporadically. But enough to make it unpredictable and ultimately unusable for me.

@sundaytone Ай бұрын

I feel like midi can definitely be unpredictable. I had an issue like that where the HX One wouldn't pass the midi clock to the next pedal and I spent a bunch of time trying to figure out what I did wrong. Eventually I realized Line 6 had an update for the HX One that solved the issue for me.