The video is a little old so it is probably taken care of by now but for what it is worth I just fixed my 2005 Z71 5.3 Tahoe with 330,000 miles on her, I can almost guarantee that it is the oil pick up tube oil ring and it will just keep getting worse, you will start to aerate your oil and develop some lifter tick and it will just plain fail completely pretty soon so it best to tackle it now. 4x4s are kind of a pain to drop the pan but it is not too bad, but bad enough that you don't want to re-do it right way so replace your oil pump while you are there. No need for high pressure or high flow pumps, get oem or a Melling standard pump they come with the o-ring (cost is about $120.00, oil pan gasket $60.00, timing chain gasket kit $45.00), if you know what you are doing (I did not) and have the tools (I did) you can get done in a half of a day, easily over a weekend (I am Electrical Engineer not a mechanic, so what do I know). My Tahoe now runs like a brand new truck 45 psi on start and almost 60 with a light rev, it really feels like a different vehicle.

I have several friends with these GM V8 engines. Try using 5 quarts of 5W30 oil and then adding 1 quart of Marvel mystery oil (or) transmission fluid at every oil change. This can help to clean the engine long term while not being so harsh as the solvent in the motor flush that was used in the video. The white lines in your oil as it was draining were metal particles, most likely worn bearings. So yes there is some wear going on in your engine but it does have a lot of miles so it is what it is.

I had A 2005 Silverado with 5.3.. It was the O-rings in the pickup tube.. One where the pickup tube is joined in the middle and another O-ring where it mates up to the oil pump. Both O-rings were deteriorated and allowed it to suck air. The bad part for me was it was a 4WD truck, and I had to remove the transfer case in order to remove the oil pan.. to install two $2 O-rings. Also, I switched from SAE 5W-30 to SAE 10W-40. to improve oil pressure on a engine with 200K miles. It now has 310K miles, and is still holding pressure.

I use the same flush for my wife’s friend. She has a Kia soul I did 1 quart of transmission fluid and one flush at the same time for 30 minutes and it was fine and it cleaned it really good. she’s a single mom. She would go over on her oil change intervals

I had the same issue with a brand new swap engine in August of 2022, it seems these swap engines sit on the shelf for weeks or months at a time before they wind you in your driveway for installation into your vehicle, with that said my new engine sway had very low oil pressure on my initial startup but no tapping or knocking, so I changed the sending switch with zero effects, I then did an oil flush still nothing, my next step was to pull the oil pan and replace the oil pickup tube o-ring, however while I had the oil pan off I installed 10 small washers in the oil pump spring housing, please note when I pulled the oil pan the pickup tube screen was clean as a whistle, which lead me to believe my oil pump was working correctly but not producing the required oil pressure, so in stead of removing the front engine cover I simply installed 10 small washers to the oil pump spring and now my oil pressure reads 40psi at idle and 60 at throttle, I can't say with any certainty that this trick will work for you I only used this after watching several video's that showed using small washers on the low volume stock ls oil pumps will increase your oil pressure, and you should know that the high volume oil pumps come with a longer and stronger spring or with small washers, it all depends on the manufacture you purchase your high volume oil pump from, hope this helps anyone who is dealing with low oil pressure on your GM or Chevy ls engine.

Oil sending unit, including screen, and oil pump pickup oring. Probably the most common issue on these engines. Can’t imagine pulling an engine and then finding out it was just the oring lol

I have a 2000 5.3 , 260,000 runs strong. The pick up tube o ring seal is the most common problem with low oil pressure on these. In your case as dirty as that oil looked. I would have went a step further and drained it after the flush and filled it up with straight kerosene and pulled ignition fuse to turn it over a little without starting the engine to circulate it thru the engine and let it set a couple days. Then turn it over again. Then drain and install new oil and filter. This would really clean the sump screen and the whole system. My oil pressure is good now. No tick at start up. 40 at start up and 30 idle warm. Try it before you tear into it. Don't be scared.

5-10 psi at idle up to 20psi seems like a win. Like the others say check the pickup o-ring when you address the pan gasket but on old sbc the dealer only needed 8 psi at idle to not have to do warranty work

It’s your o-ring bud goes from pickup tube to oil pump

Im sure this is remedied now but the likely culprit is a bad oring on pickup tude and or the screen on the sensor being clogged up. At 230k miles itd be beneficial to change oil pump and timing chain as well.

I'm "spectacle" too. Hahaha. Seems the motor flush doesn't clog anything up if you do a basic oil change after a couple hundred miles after the flush since the residue isn't going to clear out immediately after flushing. Full synthetic will keep gradually cleaning after initiial flush. I pulled the pan off my 5.3 to replace the gasket after flushing and basic oil change a week later, and no issues. Slightly raised oil pressure btw. 5 psi I believe.... Which was exactly what the truck needed. Didn't want to play games with clogging the oil pick up and it was clear after that process. Just my experience. I did it to a 302 Windsor that was sludged without another basic oil change a week later and after a couple months, lost oil pressure and threw a rod. Oil pick up was clogged. Don't be afraid of motor flush if done with good intentions. If it's really sludged, just drive it for as long as possible or take the chance and do multiple oil changes in short intervals. I also prefer using an oil stabilizer after for piece of mind with leaks and added lubrication since I don't mess with new cars. Just my experience being a shade tree mechanic and glorified parts changer. Not an actual mechanic.

Why not use Amsoil motor flush, i see Amsoil Keychain or something when started your 5.3, i have 6.2 Denali same problem. I did Amsoil flush it did help ,with some heavier oil. Used 10-40 have bout 230,000 miles. Nice video

Mine is an 02 Tahoe with 250k miles and it had just one quarter of the oil pressure and making a lot of lifters noise and I did replaced the O ring on the oil pump and put 3q of diesel in the engine with 3q of old oil and ran it for 10m on idle; put new high mileage oil and now sounds like a brand new engine . I was desperate because I was thinking of replacing my engine, it’s been 9k miles since and still running strong. Note : do your oil change more often. I do mine every 3500 now before this problem I did it every 5000 miles.

If you use the flush and the bearings are War you're going to remove all the crud around the main bearings and you will have worse oil pressure is some of the crowd around your bearings to help keep up your oil pressure if your oil pressure is that low then you have other problems you need to diagnose what the problem is and fix it the right way the pickup tube o-ring would be a likely possibility a leaky or bad oil pressure switch be leaking oil also check for exterior leaks putting the flush in your vehicle will probably cause your oil pressure to go down more especially with a motor that has a lot of miles on it for example a vehicle that has 108,000 miles the bearings are worn putting flesh in your vehicle will make your oil pressure drop even more

I would replace the oil pump and rod bearings . I have did a few cars and instant oil pressure .🎉

Make sure you use the ac delco or fram motor oil filter .

I got an Escalade ext with the 6.0 the oring is not always the fix. I put a melling high volume oil pump with a new oring and my oil pressure still goes down once it’s warm. It’s more than likely worn bearings

Drive that ole girl, I have a 05 5.3 that I’ve had since new and the last 6 years I’ve had no oil pressure at idle, you just got to nascar drive it with both feet,When you come to a stop . My truck has 411,500 miles on it , still going! Drive it every day, it’s at just under 40psi of pressure when driving down the road. It’s like others have stated, pick up tube o ring and pick up screen clogged that will fix your problem.

Just had the same problem, new high volume oil pump and obviously the new o-ring. Now I’m over 60 psi on throttle and over 40 at idle.

For those thst have this issue. Try pouring 1 or 2 bottles of ATP-205 in the oil. It's a seal conditioner/sweller. Fully compatible with oil so you can leave it till next oil change. In these engines the o rings get shrunken and hard over time and ATP-205 will make them as close as new.

Marvel mystery oil help mines a whole lot I had thick mud like sludge coming out mines had a hard knock put this stuff in and worked perfectly

Bro that's a beautiful truck whatever it is just fix it I have one it does not die

I have that problem too. Found that i have some sludge on my engine. Idk about flushing it is a 280k 2005 chevy silverado 5.3 LT.

That's A Nice truck, Anyways Mines Doing The Same Exact Thing At Idle BUT Once I Drive it, It Doesn't do it Anymore..

I changed my oil pressure sensor, filter and Oil pump. PSI lives at around 18 to 20 psi.

On my LS3 the oil pressure drops to 13-15 psi when the oil temperature is 245F and above. I don't know if it should be like this or not.

the white grey streaks are likely to be bearing material.

I have 2010 about 2 years ago my gauge did the same thing.removed oil screen .now have 45 to50 lb no problem now. Oil change 3 to 4000 mi. Has 245.00 miles . I just put too copper tires on front today.

Lol. I just did this a week ago. Set up to do the pickup tube and o-ring and wasn't able to do it after just having back surgery. So I was like fk it, (had that exact bottle that I never used) started it up after that and running at close to 40 and 60 accelerating. So grateful that it worked. I'm sold on that way of cleaning it out... definitely worth the try.

try 10W 30 helps with oil pressure.

If you still have issues afterwards. Then you know you done all you could and it's time to tear into it. Also I have found that changing the tiny oil filter between oil changes helps with oil pressure too. That's a tiny filter for a V8 engine. It clogs quickly.

Change the oil galley as well plus the oil ring

No gauge swipe on koeo ? Is that normal ?

Had the same problem did oil pump kit I did a high pressure pump I’m 45-50 at warm idle

Change your oil pressure sensor to see if thats just going out or clogged up.

I wonder about the quality of the oil.

Is a motor flush a bad idea, no it helps remove harmful varnishes and other gunk, i personally us atf fluid to flush mine, will it help clear up a slight ticking if you have noise, yes it can, can it fix a problem with low oil pressure or burning oil, for the most part no, if you have low oil pressure or burning oil youll have parts that need replaced, in this case most likely an oil pump and a few gaskets

How do you like the AF Dynamics intake? I’ve seen them on Amazon and didn’t know how good they are.

you have to cut the oil filter to check for metal.

I have a 2004 Silverado 4x4 with a 5.3 that has 210,000 miles on it, I bought a few months ago and started to get a check engine light. It was for the knock sensors. So, I replaced them. Pain in the ass, you have to pull the intake manifold and the fuel injector wiring is a nightmare to remove without damage. Then I started getting a low engine oil pressure warning on my display. WTF? How are they even related? Anyway, I replaced the oil pressure sending unit (another pain in the ass) and changed the oil and filter with a factory oil filter and 10w-30 synthetic oil. It changed nothing. Plus, my instrument panel shows 40 psi oil pressure all of the time, even with the engine off. I have driven it for a few thousand miles, and it runs well, just get the annoying oil pressure warning every 15 minutes or so. Took it to a shop and he said it might be the engine management computer and the oil pressure gauge issue would require an instrument cluster replacement. Lots of money to get rid of the issue yet it runs fine. Being a diesel mechanic all my life, I told the shop, if the oil pressure was that low it would have blown up long ago. I'm just going to run it for now and put up with annoying oil pressure warning. Thanks for the video, you have a NICE truck. BTW the 5.3 has lots of hp and tows my trailer like it was nothing. :)

buy this Liqui Moly 2037 Pro-Line Engine Flush - 500 Milliliters , 3-4 bottle and by cheap walmart oil 5w-30 and flush it 3 times, and drop the pan to check

My 6.0 has 280k and I just 😊it diesel 15-40 in it and gained 10 psi while drive idle site at 40 instead of 30 lol

i got 311000 on mine. still good oil pressure

Same problem on my 13 silverado 5.3. new oil pickup and new seal ring on pickup tube problem solved back at 40psi. my 5.3 has 234k

Like others have said. It's probably the O-ring on the pickup tube

O ring/pickup tube/oil pump..Fel Pro with red grease lube...Save your money for the next 5.3 build to teach GM's big mistake on this design flaw..No Motor Medic from Dollar Store......

Ok so I have a 2000 Z71 with the 5.3 188000 miles same problem as yours my mechanic dropped the pan cleaned it out because he said it was full of crud and I have owned this truck since new and also always run full synthetic replaced the pickup tube the o ring to it plus another o ring don't remember what it was called and replaced a screen on the sending unit my pressure was at 20 just like yours now after all this I'm back at 40 at idle and on acceleration back up to 55 60 psi more than likely yours needs the same thing

It’s definitely the pickup tube oring I’ve fixed it on quite a few of these

I opened up a 5.3, i cound't believe the slug in the motor. I would flush it again... At least a gallon of slug/grease.

My 04 has this same problem and it pisses me off because there is no good reason why they did the oil pickup with a o ring instead of two machine surfaces

Thats a sexy pickup

25 psi oil pressure is the minimum, 65 psi is the maximum.

I have a 07 new body style Chevrolet Silverado four-wheel drive with a 6.0 LTZ 220,000 Mi and I put three oil pressure sensors in in the last 2 months my gauge doesn't work gauge doesn't work and truck is wanting to cut off on me after it gets warm anybody have any ideas what it might be

I heard using c phone and your oil changes helps out a lot to a cleaning out the engine

I've changed the sender, sender screen, O-ring, and the oil pump!!! Still very low pressure.. This is my last idea, although I hate to flush anything.

DAWG, THAT COLOR IS CLEAN. Hope you get it all squared away

They say ur suppose to let it run 10 min then drain and add clean oil again

It's an old engine.... Put thicker oil in it

There's two types of motor flushes... Solvents (diesel, rubbing alcohol, ect) And Detergents ( lab made chemicals specifically designed to do one job and one job only, flush the sludge and revive/unharm seals) Your flush is the crappy solvent

That was supposed to say Is sea foam

Drop your oil pan and drop the pickup tube change the o ring then install it all back.

It is almost always oil pump pick up tube O ring.

Mine has 300k. I run 10w40 Valvoline maxlife and it has 40 at idle and gets higher with rpm

that is not a real oil pressure sensor on the chevy , you should find the oil sensor and replace it and or put a real oil sensor that uses pressure

I’m having the same problem but my engine only has 1800 miles on it…

Please stop trusting the cluster gauge. Hook a scan tool up to know for sure what your psi actually is!

It looks like i seen silver bearing material or cam wear

My truck is doing the same exact thing

Running at 40 lbs is ok

Just move to 10w-40 amsoil and call it a day.

Go 10w-40 or 50

Well your first problem is the oil you’re using… valvoline is absolute trash!.. put some castrol edge or Pennzoil ultra platinum in there.. your truck will thank u 🙏

It's your oil pump...it's bypassing

It’s kerosene.

Change the filter. Seems simple but that’s all it is.

change oil every 3000 to 4000 miles never go beyond that.

Bearing material bro

replace your main bearing.

I replaced oil pump to a high-volume oil pump I replaced pickup tube check my cam bearings when I had oil pan off everything look good I replace oil pressure sensor screen the gauge in the truck would have 50 lb of oil pressure cold start idle around 23 lbs warmed up to 210 running temperature 39 lb of oil pressure running down the freeway step on it really hard let it go back down to speed limit engage with slowly descend to zero put an external gauge on the prime hole on the side of the block where your oil pump is cold start had 80 lb of oil pressure warmed up to 210 had 59 lb of oil pressure but the gauge inside the car was saying I still had low oil pressure doesn't make any sense now I need to check the oil pressure at the oil pressure sensor but that is really hard to get to to hook up an external gauge my next step is going to be checking the oil pressure off of my oil cooler line I will have to tap into that and put an external Gage just to see if my oil pressure changes.

Did you ever figure this out?

Update?

Take oil screen out

Did you know the monkeys that designed and engineered that abomination of a 5.3 liter engine. Each generation GM tries to make the worse engine/truck combination. My 2007 Tahoe has 315k and I never knew who or when the oil changes were done. I now have the low oil pressure warning. I think it was the two containers or bar stop leak, pint of STP and pint of AT 205 I put in it a week ago. I two will fill oil reservoir with motor flush and gamble.

Snake oil

burnt oil contains a lot of metal

Spun main bearing...now all the bearings are shot. I could see the bearing shards on your catch pan

I have the same problem just changed my o ring on the pickup tube didn't help. FUCKING POS GM

I have a 2004 chevy Tahoe 4.8 and I was that same issue so I changed the oil sending unit and it fixed it. But two weeks later it started again showing low oil pressure but I have been driving it like that for two weeks and nothing has happened. I was thinking of an oil flush but now I don't know what I should do.

You gotta believe...