MyEnergi Eddi Temperature Sensor Installation. Relay and Sensor Board.

Рет қаралды 4,428

10 ай бұрын

In this video I take you through installing the MyEnergi Eddi Relay and Sensor board in the Eddi and then attach a PT1000 temperature sensor cable in order to see the temperature of the tank on the eddi and in the MyEnergi App.
Amazon UK - Temp Sensor PT1000 Cable - amzn.to/3XhmL4V
Don't forget to LIKE and SUBSCRIBE to the channel: / @daniel_coe
Get £50 when you switch to Octopus:
Use this link share.octopus.energy/tough-sn... or use my code "tough-snail-7955" either when speaking to Octopus on the phone or once your account control panel is live and you can enter it in there or even email Octopus and tell them.
My camera equipment:
Manfrotto Tripod - amzn.to/2SVK6Xj
Canon M6 MkII - amzn.to/3rYPSbM
Takstar Microphone - amzn.to/2GsUepg
Samsung Galaxy S21 - amzn.to/3nf4G6E
DJI OM 4 Gimbal - amzn.to/33UT3by
DJI Osmo Action Camera - amzn.to/3rzkHH5
DJI Mini 2 Drone - amzn.to/388NZ5E
Andoer L4 Pro Camera Slider - amzn.to/3o8aMDU
Amcrest Webcam - amzn.to/3tZ85as
RODE Mic Vlogger Kit USB-C Edition - amzn.to/3v5OKqR
RODE VideoMicro Microphone - amzn.to/3W6fdjX

Пікірлер: 23

@damianluby8973 Ай бұрын

Cheers for the video, I installed mine with minimum fuss because of your video 😁

@JohnDavis-xv1nm 2 ай бұрын

Really grateful for the video, Daniel. I managed to do all the connections, etc almost exactly as you showed. Biggest problems I had were using the fiddly cable ties to secure the sensor cable and then Gorilla taping the sensor to the tank - our tank is a bit like yours with very little easy access. However, pleased with the results. Thanks again!

@user-gv5mw9sz2j 6 ай бұрын

Thanks mate 👍 useful video

@daniel_coe 6 ай бұрын

No problem 👍Hope it helped.

@ciaranmcmanus6081 5 ай бұрын

great video very informative and well explained two many ads in my opinion but keep doing what your doing.

@daniel_coe 5 ай бұрын

Thanks, will do! Sorry about the ads, that's Google and KZfaqs fault. They choose how many you see, even if the channel is not monetised.

@elwexicano 3 ай бұрын

Really useful video, thanks for that. Can you set the eddi stop sending heating the immersion once a certain temperature is reached?

@barryduggan6307 3 ай бұрын

Hi Daniel, great video, recently got an Eddi installed with our panels, really do like it, I also went and got the relay board and sensor after watching your video, I do like to know the temp of water especially in the evening after excess solar is finished topping up Eddi, can I ask you where is the best spot to place the probe on a copper cylinder, it has the foam insulation around it.

@colingoode3702 10 ай бұрын

Good info Daniel & something I'd be interested in doing. The only snag I have is that my Eddi is in my garage with the inverter, battery & consumer unit & my HW tank is in the airing cupboard a good 20m away with no easy route for the sensor to go between the two. I guess I could look at moving the Eddi into the airing cupboard but that would give me issues with the CT's that are connected to it. I guess I could get a Harvi & connect the CT's wirelessly but that starts to make the whole exercise a bit expensive just to get a tank temp reading with no added benefit of control. More thought needed on my part I think.

@daniel_coe 10 ай бұрын

Yes, it sounds complicated. I only did it as it was quite straightforward for me and not too costly.

@AM-tn8yu 10 ай бұрын

Brilliant video. So we'll explained. Would u need 2 probes..one for each tank..I have an ordinary emersion..tank 1 sink and tank 2 vath

@daniel_coe 10 ай бұрын

Yes, you can have two probes, one for each tank. You'll then see two temperatures

@AM-tn8yu 10 ай бұрын

@@daniel_coe thank you v much

@Jp-jk1gj 9 ай бұрын

Thanks for the video - its very helpful. I installed the exact same set up but the temp reading on the Eddi does not go above 32-34c - I know the tank is at 60c+ as I get the max temp reached message on the Eddi. Are you getting accurate(ish) readings?

@daniel_coe 9 ай бұрын

I wouldn't say totally accurate. But when max temp reached, it's about 56, and when really empty, about 30. So I can kind of work out how hot the tank really is

@anthonyrogers2539 Ай бұрын

Hi Daniel. Out of curiosity, is there a reason you did not use a cylinder thermostat? Thanks

@daniel_coe Ай бұрын

Perhaps as I don't know what they or what they look like. I'll have to do some research.

@razorg4421 10 ай бұрын

Im trying to get my head around the Eddi. I get that it diverts excess solar to heat the boiler but how much does it actually save? Im thinking winter when their is no excess solar. Gas is under 10p a kw. I only have a 2kw PV system so even in summer I only really generate 9kw a day & I have a 9.5kw battery & an EV to charge. Would you say an Eddi would be pointless for someone like me?

@daniel_coe 10 ай бұрын

First of all, you need a water immersion tank. Then, if you don't have excess solar, it's probably not worth it. If you do have excess, you then need to work out if exporting the excess solar and using gas is cheaper than heating the tank with solar. But for some, it's not all about savings, but being green also. In the winter, we still use the boiler to heat the water as there isn't usually enough excess solar

@glyn1782 10 ай бұрын

👍👍👍

@villageidiotdandan 10 ай бұрын

Apologies for a silly question, but what benefit does this have please? Why would you want to know the precise temperature of the water in your tank?

@daniel_coe 9 ай бұрын

Some days, it doesn't reach full temperature, so I can work out if I'm in for a slightly cooler shower than I really want. Plus, I can tell when my teenager has had a 30 min shower and taken all the water!

@villageidiotdandan 9 ай бұрын

@@daniel_coe Ahha, thanks, this makes sense. I can see that it will help you establish the best times to set your gas boiler to top the heat up