@ChadSchimmel Жыл бұрын
That is a great finish, My go to for sure :)
@TurnersTv Жыл бұрын
lol
@RoundTownWithMike Жыл бұрын
Thanks Chad! I was doing it a bit out of order using Yorkshire Grit last. This is helpful!
@TurnersTv Жыл бұрын
Glad it was helpful!
@LewisKauffman Жыл бұрын
Thanks for the comparison. Love the Yorkshire Grit products!
@TurnersTv Жыл бұрын
Thanks for watching! and yeah we are really loving the Yorkshire as well :-)
@_zhawkeye_9808 Жыл бұрын
...thanks for this comparison...definite improvement with the yorkshire...👍 Matt
@TurnersTv Жыл бұрын
Absolutely. Thanks for watching!
@michaeldozier3008 8 ай бұрын
Great video, thank you
@TurnersTv 8 ай бұрын
Glad you liked it!
@jpwoodwork Жыл бұрын
Great video! Yorkshire Grit is awesome
@TurnersTv Жыл бұрын
Thanks! We are really loving it as well
@granjamo 7 ай бұрын
What speed is the lathe running for the sanding and application of finish?
@TurnersTv 7 ай бұрын
Sand at 700-900 and then start the Yorkshire at 700 and increase to 1200 every little bit while using Yorkshire. Turn back to 700-900 for the friction finish. Hope that helps!!
@jjbaty4337 18 күн бұрын
Great video! When I tried method 3, I seem to get a surface that is not as smooth as it was after sanding to 400(cocobolo pen blank). The end result seems to have ridges. Maybe this is the gumming result you referred to by using too much polish or possibly not moving my rag enough. Any ideas are appreciated. I’m going to sand off and try again making the two aforementioned corrections.
@TurnersTv 18 күн бұрын
Yes when I have had that issue it has been because I was using too much polish. Also really make sure that your paper towel or rag is clean / that you have gotten all off the Yorkshire off. Let us know how it goes!! :-) Hopefully you will have good success this time around
@jjbaty4337 18 күн бұрын
Thanks guys for the quick reply. I’ll let you know.
@jjbaty4337 12 күн бұрын
To get back to this. Problem Solved! I appreciate your suggestions . Yes, I was using way too much. When applying a minimal amount to my paper towel, the problem went away. Thanks again for your help and education.
@TurnersTv 11 күн бұрын
Awesome! I am so glad it worked out :-)
@gordcameron4409 10 ай бұрын
On the Mylands website, the instructions for the friction polish say apply, then wait for 5-10 minutes before applying friction / buffing. Have you tried that? Thanks.
@TurnersTv 10 ай бұрын
Sometimes we wait between coats, but no, it is so dry here in AZ that we generally go straight to friction pretty quick. We might have to try this though. Have you gotten better results that way?
@gordcameron4409 10 ай бұрын
I contacted Mylands about this, they say that either method works, waiting for the polish to dry or buffing right away.
@georgebrill3072 4 ай бұрын
Is friction polish durable enough for a pen? Thanks.
@TurnersTv 4 ай бұрын
Yes! It is what we use on pens the most 😃
@georgebrill3072 4 ай бұрын
Thanks.
@georgevalente4223 Жыл бұрын
Thanks... does Menards or Loew's sell friction finish? I don't want to make it.
@TurnersTv Жыл бұрын
I'm not sure, but we sell it and we ship all over :-) Here is the link to it on our website www.turnerswarehouse.com/products/mylands-friction-polish?variant=31464147910739
@aldacey8458 8 ай бұрын
You never buffed in the friction finish on the first two. Stupid comparison
Фани Хани
Рет қаралды 1,2 МЛН
WYOMINGWOODTURNER
Рет қаралды 8 М.