Thank you for the information. i was able to readjust my settings. you all are Awesome!!!

讲得很好👍

where can I found this part for my electric mountain bike this same model

P01：Backlight lamp brightness, level 1 is the most dark, level 3 is the brightest; P02：Unit mileage, 0: KM;1: the MILE; P03：Level of voltage: 24 v, 36 v, 48 v, 36 v (by default); P04：Sleep time: 0, means don't sleep;Other Numbers means for the sleep time, range: 1-60;Units of minutes; P05：Assistance gears:0, 3Mode：1lever 2V、2lever 3V、3lever 4V; 1, 5Mode：1lever 2V、2lever 2.5V、3lever 3V、 4lever 3.5V、5lever 4V; P06：Wheel diameter: unit, inch;Accuracy: 0.1; P07：Speed measuring magnetic steel number: range: 1-100; P08：Speed: the range 0 to 50 km/h;The default 50, 50 said not the speed limit; Note：when the speed is greater than the set speed, shut off the PWM output;When speed down to less than the set speed, automatically open the PWM output, driving speed to the current + 1 km/h; Numerical based on km as a benchmark here, after the unit set from miles to miles, display the speed of numerical value is automatically converted to the correct miles, but miles under the interface of the menu in the values of speed limit set by the data conversion, MPH speed limit values are not consistent with the actual display, P09：Zero start, non-zero start setting, 0:0 start;1: the non-zero start; P10：Driving mode setting 0: power drive (decided how much output power by power gear, at this time to turn the invalid). 1: electric (by going to drive, steering gear is invalid at this time). 2: power drive and electrical drive coexist (electric zero start state is invalid). P11：Power sensitivity setting range: 1-24; P12：Assistance start the intensity setting range: 0- 5; P13：Power magnetic steel plate type 5 Sherwin grain of magnetic steel three types; P14：Controller for the current limit value to set,12A(by default) range: 1 - 20 A;

How do you reset it back to factory settings?

Hi how do I order a new LCD screen for my fat tire bike> I've called the number on the website many times and emailed. please help

Can you reset a S 861 display controller panel i only get 3 bars of power can't get to speedometer its at 0.4?

Can you show all The factory settings I have a 37 volt 7.8 amp battery and a 250 watt motor

Hello, Does anyone else own a Nakto fat tire mountain ebike as well and know an ebike shop in the Philadelphia Pa area willing to repair it? Not sure what my bikes electrical issue is and I've replaced the throttle, rear hub wheel( original damage issue) and contol box in an effort to weed out the issue since a black ice fall in December!

I have motor error, how can it be reset or where is the error? Wheel does not turn battery fully

hi , i fallow this video , but the ebike only work if the light is on in the display , and i have no kmh recorded ...it stay at zero ( i have 48v ebike )

how can I find a manual for all the other settings?

how do you raise the top speed?

Can you are explain all the P numbers

Why does nakto not put any info in their users manual. How do I turn on the headlight??

И сте ли от този вид дисплей? Искам да поръчам

Mine doesn't even turn on properly just have a empty screen with 4 lines like it wants me to put a code or something

What model lcd is this? Is there a manual i can get? I have 17 settings not 15

esiste un manuale di settaggio in italiano?

Damn, I need a new LCD controller

WTF just want to change to the speed to 28mph.. how does one follow a video like this? 😂

Please, how do you reset controller?

На русском есть инструкция?

Unfortunately very strong accent, so very difficult to listen & understand. Not for public presentation, what have to be clear & good English.