H. Kiga. My frind can i bay something and ship to Saudi Arabia

Good work!

Can buy some from you and ship to Australia

Can you help with shipping?

Nice uv light box

Thanks!

@Mitchell Collar tokyohl.com/mycreation/90.html this is the item

Como fazer uma armação desse tipo sabe como?

Jolie travail !!!

Thanks!!

その通りです！Tシャツくんあるあるですよね。マニュアル通りにやって失敗される方多いと思います。

Obviously not op but I do this kind of stuff. You're going to need TRANSPARENT printer paper. I use the ones from Michael's that have adhesive, usually used for crafts. They stick onto the silk screen nicely. youll also need a silk screen. Get them from Amazon. Get one of the smaller ones. Next you need to find your design, or make it, and then print it onto your paper. Next buy your emulsion from Amazon. It's from speedball. It's a two step process. It should have two bottles. EMULSION. Then coat your screen with emulsion, spread evenly with a squeegee. Avoid bubbles, don't lay it on too thick but not too thin either. It should look wet. Let it dry flat but suspended. I recommend stacking too boxes on either side and balancing the screen on top. And let dry in a DARK place. Your garage should be fine. Emulsion works by hardening in the sunlight or any light for that matter. It's a thermal process. After it's dry, stick your paper with design onto the front part of the silk screen. That is, the part with the large dip. The flat side should be down against your shirt later in your process. After you have stuck it on youre going to need a light bulb that gets very hot. Either incandescent or something more intense, like outdoor floods. OP used uv lights which also works nicely but you can use a regular lightbulb. It will be less precise though because lightbulbs vary quite a bit. Florescent and LED wont work because they don't get hot!!! Shop lights work well. Just look it up. Position the lightbulb about 1 foot from the screen and leave it. For about 5 minutes. Peel your paper off and spray it with warm water, not hot, but luke warm. Don't spray too hard or you'll take off the design. Spray where your design was and you should see it is slightly lighter than the rest of the screen. That's because it wasn't burned and won't hang on as easily. Use a sock or microfiber cloth to lightly scrub the back of the screen with spraying the front. Then switch sides and repeat. You should end up with a good print. You're also going to need silk screen paint. Speedball also works. You're going to need a squeegee. Tape up the edges around your screen without covering your design. Get a good line of paint across the top of the screen and bring your squeegee up and down, 1. down 2. up 3. down. You don't want to lay it down more than three swipes or your paint will be too thick on the shirt. Usually a 1.2. swipe is fine. Look at the shirt through the paint and see if there are any spots the paint didn't coat on the shirt. Go for the third swipe if there are blank spots. Don't do more than three!!. If there is still a spot you can use a gifit card as a squeegee in a small area.or just fill it in later with a paint brush, (not recommended tbh). IMPORTANT IMPORTANT: PUT A PIECE OF SMALL CARDBOARD OR POSTER PAPER inside shirt before printing. This will keep the ink from seeping through to the other side. Let hang dry for an hour and throw it in the dryer. Or let dry and iron with parchment paper like OP did in the video.

PUTUTIK NETWORK if u use google chrome it will automatically translate to english

do someone have amazon links to buy the stuff?

@@TexasKen Thank you!

@@lawrence-yx1ew THANK YOU

That exposure box looked real smart and compact! Is it a DIY construction?

Mihai Marcu thx

@@haikopaiko yes

Taiyo seiki?

Of course, it cannot be repositioned in exactly the same position as in the initial state, but the deviation is negligible.

@@necotadotcom When I used to do screen printing, I would use reference marks at the corners. If you put tape on the t-shirt where the reference marks are, and print the reference marks onto the tape you can re-align the screen perfectly!

@@tiggerbiggo He was asking about he took out the silk screen and put it back in. Not the reference marks on the t shirt design itself. Like when you stretch a piece of fabric and it distorts. I agree with the first answer. The distortion won't be too drastic unless you're dealing with 'pixel sized' details.

@@dawniebug784 Right, but surely what I suggested would solve both right? That way it doesn't matter exactly how the film is placed in the frame, just align it with the reference marks

Thanks! In the beginning, it sometimes failed, but after doing so many times, I became able to do well.

@@necotadotcom could you please make a list of what we need to buy to create the same process as you ? I would like to try it so bad

yes but the fastest way if you want 500 of them. For one single shirt screen print is the slowest way.

@@danbarb9728 what about heat press ?

I agreed

ありがとうございます!!

We r u from Camila?

Bon travail

Good job

Following for notifications

Terima kasih!!

I'm interested too ,( from tunisa btw )

yours probably works with UV too, normal incandescent and fluorescent lights also emits UV light, guess he's using pure UV light because its more efficient maybe?

I purchased and used the screen with the emulsion coated. I do not know the type of emulsion.

Wow!! In my country there are not that products. Thanks for your video and your reply. 👍

@@necotadotcom hey man Nice video! Where can i buy the emulsion coated screen?

this is the name of the screen for those who want to know 太陽精機Tシャツ (Taiyo Seiki T-shirt)

it's the standard photo emulsion liquid. You can get specific kinds that setup in different kinds of light. If you've never done it before and don't want the screen cleanings/ drying wait times you can buy screens already coated. I recommend daizo speedball for emulsion easy to use and purchase. Exposure times are short and cleaning is fast. Blick for the ink and speedball for the emulsion.

Damn you want him to Make your shirt too?

you can buy @ amazon japan, shipping is no problem

www.taiyoseiki.com only sold in japan

コメントありがとうございます！ いえとんでもないです欲しかったので勝手に作っちゃいました😅 これからもFWT応援してます！

Thanks!!

Follow answer too

I want to know too

Does anyone know the name of the frame and where to get it?

私も買いました 上手に出来んかった

Kira kira kalo di cuci luntur gak ya? tulisannya bisa kelupas atau pecah retak² gak ya?

@@akbarerlangga9764 engga om , disikat pun masih aman

@@yogisutrisno ini mah sablon ya, baru ngeh saya :'D Soalnya cat yang dipake di video ini, alat alatnya, dan tekniknya keliatan lebih modern daripada di negara kita :D

Iya emang ini prinsip nya sablon manual rubber atau Plastisol , cuma ini lebih simpel n praktis bikin screen nya , tehnik gosok nya sih sama

Iya standar banget ini mah. Ga ada yg aneh kok

www.amazon.co.jp/%E5%A4%AA%E9%99%BD%E7%B2%BE%E6%A9%9F-02-3901-T%E3%82%B7%E3%83%A3%E3%83%84%E3%81%8F%E3%82%93%E3%82%BB%E3%83%83%E3%83%88/dp/B0058QIWK6/ref=cm_cr_arp_d_product_top?ie=UTF8

Seriously?