That has to be a series of extremely useful tips for those folks who have one of these who have a similar or same NH baler to this machine Ted. Just brilliant helpful advice for dealing with this nightmare problem - it has to be really exasperating for anyone in this situation with a crop needing to be baled!
@tedkahler97387 жыл бұрын
It is sure a pain in the rear... especially when the rain is comming and your messing around with your net wrap!!!
@adamramsey9067 жыл бұрын
Thank you for doing that Ted. I have not had those issues yet, but checking those few things will become part of my start up checklist.
@tedkahler97387 жыл бұрын
Atleast you know in the future if it does happen
@elmcustomharvesting10727 жыл бұрын
I can't find the net wrap on my baler. thanks for the video it is very useful for people that have round balers not Square balers. hope you have a great day
@tedkahler97387 жыл бұрын
YOurs just has that really heavy twine that gets tangled on everything.... should have a wrapper on the back of your big baler ... that would be pretty sweet!
@jimlbeam29 күн бұрын
Thanks just what i was looking for
@levimandel47873 жыл бұрын
Don’t forget about the duckbill adjustment …Your tips are spot on 👍
@tedkahler97382 жыл бұрын
thanks
@achieversgymnasts4 жыл бұрын
thank you for posting...very informative. keep em coming!
@tedkahler97384 жыл бұрын
achieversgymnasts thanks I really appreciate the kind worrs
@SoybeanFarmer33007 жыл бұрын
another point in case of how it is good to understand the operation of your equipment.. well done Ted.
@tedkahler97387 жыл бұрын
Thanks soybean farmer
@allanhartmann65496 жыл бұрын
I was having that exact problem on our NH baler! Extremely helpful video. Thanks!!
@tedkahler97386 жыл бұрын
Were you able to get the problem solved?? If you did what was the problem Thanks for watching
@alanyoung76553 жыл бұрын
Nothing beats experience....good of you too take time to share yours...👍👍
@tedkahler97383 жыл бұрын
thank i appreciate that
@howardyounger54567 жыл бұрын
thanks Ted ive never been around a round baler but interesting to know how they work.
@tedkahler97387 жыл бұрын
I should show more on how they work
@howardyounger54567 жыл бұрын
that would be interesting to me. never ran one or realy seen them run much.
@michellehendrikse72055 жыл бұрын
My baler won't leave enough net through the duck bill and I have to thread it through every bale. Had all the other issues you talked about but not surprising that the baler I brought hadn't been stored well or used for 3 years
@tedkahler97385 жыл бұрын
hope you get it going perfectly... check everthing make sure the roll turns free make sure the brake is adjusted. THe system works well when it works but it can be a pita when it doesnt
@DLKHAY7 жыл бұрын
you starting a PSA series? jk. there is so much going on with all this equipment now a days good to see someone posting their fixes.
@tedkahler97387 жыл бұрын
Yea i need to start videoing more of my little fixes.... just seem i am always in a hurry though!!
@everythingisgreenknowe50942 жыл бұрын
Really handy tips thank you. 👍
@tedkahler97382 жыл бұрын
No problem 👍
@richhalsall48811 ай бұрын
Little late seeing this video, but hopefully you can provide some insight. We have the RB 564, so a red new Holland. It ran great until we changed the netwrap. Now it’ll make the bale but won’t engage or Pick up the netwrap.
@briandavis15783 ай бұрын
Hello, I'm having a issue with my case baler. ( your monitor is the same as mine) in manual mode the it won't retract. No clue. Any help appreciated.
@dantecrenshaw41153 ай бұрын
Hello, I have a br7090 new holland baler and when the wrap gets low, it will start wrapping the bales and will not stop.
@tedkahler97383 ай бұрын
Would guess either brake is too loose or the little wheel that counts the wrap is binding up on something causing it to not touch the roll any longer
@tomservo53474 жыл бұрын
I'm running a 664. Had a helluva time running it yesterday as the net wrap wouldn't get grabbed because parts of the mesh were breaking and wrapping around the roller. I had to stop and cut the mesh off of the metal roller (that keeps the mesh inline with the duckbill) and restart the mesh. Finally ran out of the old roll of mesh and Dad and I put in the new one-and the problem completely went away. One question I have is whenever the duckbill moves in for the bale to catch I'm hearing metal on metal for a second or two like the duckbill is dragging on a roller. Surely this isn't supposed to happen is it? I'm learning the quirks and tricks on the fly with this and I'll gladly take a few mesh problems over the old Vermeer 650F we had that took SO much time to twine wrap, shut off the baler, open gate, close gate, and then pull forward 10 feet to drag up a wad of hay praying the bale would start. This year has been extraordinary for red clover hay as our 664 was gobbling up windrows sometimes 4 feet high. Thanks for the video-there are simply things a manual can't teach that practical experience does. (Oh and don't forget to release the brake catch! I forgot and wrapped a bale at least 4 or 5 times instead of the usual 2 lol.) Things have come a long way from the old Allis Chalmers Rotobaler. (That my Dad still uses. Talk about a baler that requires the most absolutely perfect hay to work.)
@tedkahler97384 жыл бұрын
Tom Servo yea I would guess it’s incerting it too far. Should be a mechanical stop so it doesn’t go in to far Had that happen once and it got caught and did thousands in damage
@scot519Ай бұрын
My bailer for some reason does not wrap, but I keep having an error on the monitor saying actuator. What does that mean?
@tedkahler9738Ай бұрын
@@scot519 more than likely actuator is not going home. Either actuator is going bad or power or sensor problem
@tebfarms9397 жыл бұрын
My Kuhn baler monitor goes insane sometimes but makes great bales
@tedkahler97387 жыл бұрын
Seems some times the newer things just like to make noises once and a while
@AndersonCattleCo7 жыл бұрын
Good vid Dads baler has something wrong in the computer because it won't even do anything if you select net wrap but it isn't worth fixing. It is $5500 just to fix the pick up so we asked what about just buying a new pick up but that is $24,000 lol
@tedkahler97387 жыл бұрын
Is the net moter bad??? or how do you know it is the computer?
@AndersonCattleCo7 жыл бұрын
service man said it was the computer but that doesn't mean he knows anything you know how that goes sometimes they really don't know much. Might check the motor now.
@brandonbewvlogs Жыл бұрын
We have that same kind of Baylor but we're having problems with the hay getting stuck up in it before even goes into the machine itself!?
@tedkahler9738 Жыл бұрын
teeth being weak can cause issues
@SeanC_ Жыл бұрын
Hi Ted. I have a cropcutter 644. When the bale is full it catches the net and starts wrapping. Then an error sounds on the box and the net keeps going. It does not retract the actuator itself. You can manually retract it on the control box and guess when there is enough wrap applied and retract fully and it cuts properly. I have replaced the sensor on the wrap roller. Any idea what to look at next? TIA
@tedkahler9738 Жыл бұрын
Have you tried to calibrate the actuator
@mattthomas5611 ай бұрын
Ted I have question on br 7090 why would the net wrap stop working when there is 1.25 inch of net left on spool I have to re thread the net every time any ideas thanks
@tedkahler973811 ай бұрын
Very possible the counter or the roller that measure the net going on is hung up and not touching the roll. Also possible the brake tention is week and not cutting good as the larger roller has more tention on brake
@cobybertram8849 Жыл бұрын
What would cause the baler not to cut the net wrap all the time. Most of the time I’m having to turn off the pto and turn it back on for it to cut. If I don’t it just keeps wrapping the bale
@tedkahler9738 Жыл бұрын
The knife should or could be in need of sharpening. The spring could need adjusted The brake could also be in need of adjustment. Also make sure the roll is spinning the right way
@IHkid7 жыл бұрын
I've had the brake too loose and wrap the bale about 7 times before I could get everything shut down. Had error code and it fell down on the shaft wrapped up on the pto and short shaft from gearbox to triple sprockets. What a mess.
@tedkahler97387 жыл бұрын
Thats never good..... always a mess when wrap gets wraped in the wrong places!
@suzikue76426 жыл бұрын
I enjoyed your video. very informative. I have a br740A round baler it has a problem im having a hard time tackling. I keep getting a actuator error i did what the book said put independent 12 volts to see if it works and it retracts and extends with power. it will retract with the controller it will not extend. It isn't making any bales. have you had this?
@tedkahler97386 жыл бұрын
i had a br 780 and a 7090 with voltage problems and towards the end of the cord where you hook it up to the battery there is a little black box thing... there is a relay in there like a 30 or 40 amp one. There is just plastic covering it. i have had the relay go bad not letting the power get to the acuator at full voltage cut covering back hooked jumper wire across terminals on relay to test that was the problem replaced the relay and problem went away... very hard to figure out the probems for sure but might be worth a try
@HaydenHostetler4 жыл бұрын
I have the exact same baler baler but its the crop cutter version and this fall late it has started slipping the belts without any hay in the chamber, it also has 0 belt pressure when it does this. so far we have rebuilt one of the pressure cylinders that wasnt holding pressure and put adifferent adjustment valve on off another baler and still the same problem.the baler only has 3600 bales threw it,i was wondering if u had any ideas to try?
@tedkahler97384 жыл бұрын
Hayden Hostetler does it get pressure on belts when hay is in machine. Could be density cylinders over full or belts may need tightened
@HaydenHostetler4 жыл бұрын
yes after it makes a small core everything works as it should u just have to be careful not to plug it first lol
@kaceywilson24825 жыл бұрын
I have a BR 780 when the net wrap gets low it won’t take it you have to pull the net wrap back out of the rolls re-threaded and then I will take it but if you put a brand new roll in it works every time perfect ~Net wrap gifts low again . Any ideas on why this is happening?
@tedkahler97385 жыл бұрын
break is not quite releasing all the way or the roll does not spin free.. when the roll gets smaller it takes more force to get roll to spin
@hernanrodriguez1188 Жыл бұрын
Hola desde Argentina! Tengo una BR7090 que no me corta la red tal vez podes ayudarme
@ronniepearson63055 жыл бұрын
I just bought a used BR780A and having problems with the net and twine starting. I think the actuator is bad is there anyway to check it ?
@tedkahler97385 жыл бұрын
with baler off and even tractor off you can have your net out and hit the wrap button and jump out of cab and spin the wheel that counts the net going on..... keep spinning and it will think that the bale is wrapping and you can watch the actuator cycle. some times its easier to do with two people. not starting could be alot of different things
@jordancarroll26526 жыл бұрын
My BR740A silage special baler will not wrap close to the edges and I have 51 inch net wrap. Any suggestions new holland folks?
@tedkahler97386 жыл бұрын
Jordan Carroll I’m running 64 inch in a br 7090 I’d be willing to help diagnose problem Make sure the net is routed properly (I know I have had it wrong before). Net needs to be comming off top of roll . Make sure all the spreader rollers are turning free have seen them get net wrapped on them and lock up or slow down. I always run the brake much tighter than they say to. So that is something to check. It’s possible the sensor became loose and the net duckbill needs recalibrated. Even possible the linkage became loose and the brake is not engaging as it should either . I could pm my number to you if you would want to talk to me more about anything
@courtneycostello5774 жыл бұрын
What would make the wrap go only to the middle and not all the way out?
@tedkahler97384 жыл бұрын
Roll on backward break not adjusted right or spiral rollers bearings going out
@nealmclain63163 жыл бұрын
We have a New Holland BR 750 Baler and been using twine and want to change to net wrap. What do I need to do to program the baler
@tedkahler97383 жыл бұрын
If you Baler is net ready you have to hit the twine net button and set number of wraps as well as load the net
@paigecarney34764 жыл бұрын
I have a 660 newholland that will sometimes auto tie the wrap but most the time I have to manually push the tie button. Any ideas
@tedkahler97384 жыл бұрын
Paige Carney what does it do when it doesn’t wrap?
@johanbotha7843 жыл бұрын
Hey. I have an br 6090. I am struggling to get it to wrap my edges of my bales
@tedkahler97383 жыл бұрын
I’d suspect the spreading rollls for the net are locked up installed between wrong or not enough brake applied As well as a problem with the actuator on where the net brake is applied
@joelknierim14563 жыл бұрын
We just got a BR750. Many times to won't grab the net wrap to begin wrapping. We have to get under and cut the net wrap to a length and then initiate the wrap again. Any ideas?
@tedkahler97383 жыл бұрын
Is your net spinning free when break is released? Is the setting for tail length too short. Normally when not cutting or starting is because it’s not spinning free when break is off
@joelknierim14563 жыл бұрын
@@tedkahler9738 I will check the brake and spinning. Does the cutting blade need to be sharp or replaced after a while?
@tedkahler97383 жыл бұрын
@@joelknierim1456 I have took knife off and filed back to sharp edge
@ryanstockwell76233 жыл бұрын
@@tedkahler9738 How do I adjust the tail length? My BR7070 is leaving a really short tail and then it struggles to catch the wrap when starting the next bale.
@tedkahler97383 жыл бұрын
@@ryanstockwell7623 have to check the book but I would make sure till is free spinning when. Brake is released first as that caused a lot of issues for me with net not starting
@mdmbike5 жыл бұрын
I have a roll belt 450 and I’ve had trouble with it tomahawking bales. I watch my levels in the cab almost every time it right on but kicks out a tomahawk bale. Any thoughts on a fix ?
@tedkahler97385 жыл бұрын
Mark Miller is the net wrapping on a roller or just making it tomahawk ? If not wrapping does you belts stop turning when you open door. If they do not your door could be opening to slow and making it bind up and writ the net as your dumping the bale
@mdmbike5 жыл бұрын
@@tedkahler9738 Thanks for get back to me. My baler would wrap just great maybe about 5 then tomahawk one then a good one then tomahawk. My belts keep turning when I eject the bale. Im new to this baler but seems to do it more and more. I can do 30 bales and 8 would be tomahawks. Most of my fields are bumpy and not all flat many hills.
@richardbennett80274 жыл бұрын
.
@erickwheeler20173 жыл бұрын
Anybody have any suggestions on a BR 780 every 5-8 bale the net wrap will not wrap the outside edge of the bale And does not cut well Changed the bearings on the cutter as the cutter bar would hang up occasionally Changed the brake pad on the net wrap roll as it was pretty worn Both improved the issue but did not eliminate it Most recently due to a poor net wrap cut pieces of net wrap got mixed in with the drive bearing and caused it to fail Any suggestions are much appreciated
@tedkahler97383 жыл бұрын
Is the roll on the correct way….. is the break mechanism working. It could be possible the sensor is failing or out of adjustment
@fitterjames374 жыл бұрын
Get a pto guard man!!!
@tedkahler97384 жыл бұрын
It was on order... and was put on ... now its traded and gone
@Northeastohio7 жыл бұрын
is this the same as the 648 round bales?
@tedkahler97387 жыл бұрын
is say the 648 is much older not sure of the similarity for sure
@tstaehnke5 жыл бұрын
I have a BR780 net wrap only works in auto intermittently
@tedkahler97382 жыл бұрын
that is never any good did you get it figured out?
@fort86292 жыл бұрын
How do you change your baler from twine to netwrap? It keeps telling me I have an actuator error
@tedkahler97382 жыл бұрын
Button for n monitor. I’d suspect there is something wrong with your actuator if it had an error pop up
@fort86292 жыл бұрын
@@tedkahler9738 thank you for the reply!! I have the actuator moving but It won't move the duck bill..im stumped at the moment.
@bigjb98735 жыл бұрын
my NH 848 baler keeps wrapping the net wrap around the roller and not the bale how do i fix that.
@tedkahler97385 жыл бұрын
Big JB 98 check roller for mud dirt if none of that check out roller for any nicks dings or welder splatters.
@bigjb98735 жыл бұрын
@@tedkahler9738 i have had it all apart before no mud or dings on the roller could it be the knife it hasent been sharpened in years
@tedkahler97385 жыл бұрын
Big JB 98 sure could be knife. Take it out and hand sharpen us what I have done on mine every year
@MartyWhillockАй бұрын
My bailer won't go back to home
@tedkahler9738Ай бұрын
Good chance actuator is bad
@marthahaggard15904 жыл бұрын
What would cause the wrap not to start on a 450ut roll belt?
@tedkahler97384 жыл бұрын
Martha Haggard any error codes?
@marthahaggard15904 жыл бұрын
@@tedkahler9738 no
@tedkahler97384 жыл бұрын
Martha Haggard is it rounded correctly
@tedkahler97384 жыл бұрын
Martha Haggard what exactly does it do
@marthahaggard15904 жыл бұрын
This baler has been doing fine until here lately it just won't start the wrap it rolls off too much wrap on the previous bale and that's the problem, on this baler if it's too much wrap off it want start
@joshuajones73487 жыл бұрын
How to fix new Holland 650 twine baler same issue
@tedkahler97387 жыл бұрын
not very fimillar with twine id guess the knife would need adjusted
@antoniobaker5066 жыл бұрын
the actuator error code keeps coming on and it wont wrap the bale of hay how do i go about fixing this
@tedkahler97386 жыл бұрын
antonio baker can you get the code to clear. Do you have Instagram might be easier to talk through there
@tedkahler97386 жыл бұрын
my name is ted kahler on Instagram... send me a pm on there ill try to help you out
@jennyplummer46134 жыл бұрын
644 bale command plus will not extend duck bill showing er 2 error whatever that is please help thanks
@tedkahler97384 жыл бұрын
Jenny Plummer could low voltage sensor could be bad or actuator could be bad
@jennyplummer46134 жыл бұрын
@@tedkahler9738 thank you sir will check that out
@jennyplummer46134 жыл бұрын
Actuator will chatter but not move where is the low voltage sensor located at and what should it read any other ideas, thanks
@tedkahler97384 жыл бұрын
Jenny Plummer would you like to call me
@tedkahler97384 жыл бұрын
Jenny Plummer I have had it over extend or over retract and get stuck. Had to take bolt out of actuator that holds it to duckbill then turn by hand to get it free re install then re calibrate and if issues continues your actuator clutch is getting bad
@Gustav45 жыл бұрын
Claas much simpler at reliable.
@tedkahler97385 жыл бұрын
Gustav not exactly seeing your point?? Not a dealer for them with ink 200 miles .... be pretty hard to convince me that you will never break down and need dealer support
@user-zu2bw7ig5v6 жыл бұрын
Solution to all of these problems... sell your NH and get a John Deere 😉
@tedkahler97386 жыл бұрын
and then you get rid of these problems and then have the problems deeres have.... every brand has its problems get over it