New Whipple Gen6 3.8 Supercharger and Nitrous Outlet Plate Kit Installation. Jeep TrackHawk Hellcat

Рет қаралды 3,659

6 ай бұрын

Upgraded from a Gen5 Whiple 3.8 to the new Gen 6 also added Nitrous Outlet plate kit. enjoy the video, feel free to drop comment and questions below.
#whipplesupercharger #nitrous #trackhawk #supercharged #spray #4wd #awd #jeep #srt #hellcat

Пікірлер: 34

@SrtifiedHawk 6 ай бұрын

Mad Respect bro. The quality of work and attention to detail is rare. I appreciate you. The video is also very detailed and helpful.

@CmoneyGarage 6 ай бұрын

🫡💪🏾 Thanks for trusting me with the bird.......🙏🏾

@GripGarage 5 ай бұрын

Great video man, keep up the great work. Clean job too!

@CmoneyGarage 5 ай бұрын

Thanks man, appreciate it 🙏🏾 🙌🏾

@RSPDMV 6 ай бұрын

🎉🎉🎉 I’m pumped Nevin

@CmoneyGarage 5 ай бұрын

💪🏾🦅

@TheMegatron673 5 ай бұрын

Very instructive video man.

@CmoneyGarage 5 ай бұрын

🙏🏾🫡

@FastWorldProblems 6 ай бұрын

Nice! That’ll be sick.

@CmoneyGarage 6 ай бұрын

🫡😎

@bamfkn_fd 6 ай бұрын

She is a ripper!

@CmoneyGarage 6 ай бұрын

She sure is.....🦅🚀

@GargoyleDanny 5 ай бұрын

Very nice keep up the good work

@CmoneyGarage 5 ай бұрын

Thank you 🙏🏾🙌🏾

@GargoyleDanny 5 ай бұрын

@@CmoneyGarage keep shining like the King u are

@chakas03 3 ай бұрын

Nice 👍🏼

@CmoneyGarage 3 ай бұрын

🫡

@gavin2465 2 ай бұрын

Awesome video. What is your fuel pump setup?

@CmoneyGarage Ай бұрын

Fore triple hat, 3 525 staged on a hobb switch. 10an feed /8an return. We also have an independent surge tank setup for the nitrous.

@gavin2465 Ай бұрын

@@CmoneyGarage what a bad ass unit!!! Congrats. 1 other question if you dont mind, who makes that intake?

@CmoneyGarage Ай бұрын

Intake is from Modal Works

@Robert68901 Ай бұрын

I would like to see the bracket you made for the front bolt

@CmoneyGarage Ай бұрын

I didn't have to make one...later in the video I found that the kit came with a bracket

@Robert68901 Ай бұрын

@@CmoneyGarage the nitrous kit?

@CmoneyGarage Ай бұрын

Yes

@crider46 17 күн бұрын

Who made the 3d printing intake

@CmoneyGarage 17 күн бұрын

Modal Works

@TENNESSEETRACKHAWK 5 ай бұрын

I hope ur not putting that on a stock stroke motor. That would be incredibly STUPID bro......The 3.8 requires a 426ci or better. If that is NOT what u have then put the 3.0 back on it otherwise ull be SLOWER.....

@SrtifiedHawk 5 ай бұрын

Nothing wrong with the stock displacement. However, this is a built 428 cubic inch motor with billet rods 🙂.

@CmoneyGarage 5 ай бұрын

This build is far from stock.....lol

@TENNESSEETRACKHAWK 5 ай бұрын

@@SrtifiedHawk EVERYTHING is wrong with a stock stroke with a 3.8 learn WTF ur talking about idiot. Hope ur going with a billet crank as well. Thats the one thing everyone skimps out on that and the thitek heads.

@tommy_Marauder 5 ай бұрын

@tennesseetrackhawk you’re talking out your ass.

@chaztaylor76 3 ай бұрын

Yeah you can tell this guys probably got at least 20-30k under that hood at least